WFW9450W
1
"
(25 mm)
(178 mm)
7
"
(178 mm)
7
"
(229 mm)
9
"
(102 mm)
4
"
(25 mm)
1
"
(686 mm)
27
"
(800 mm)
31
1
/2
"
®
5
1"
(1295 mm)
27
"
(686 mm)
38
"
(965 mm)
321/2
"
(813 mm)
1
"
(25 mm)
4
"
(102 mm)
18
" min.
(457 mm)
311/2
"
(800 mm)
1
"
(25 mm)
27
"
(686 mm)
3
" (76 mm)
3
" (76 mm)
48 in.
2
*
(310 cm
2
)
24 in.
2
*
(155 cm
2
)
1
"
(25 mm)
6
" (152 mm)
27
"
(686 mm)
51/2
"**
(140 mm)
1
" ***
(250 mm)
1
" ***
(250 mm)
76
"
(1930 mm)
27
"
(686 mm)
1
"
(25 mm)
1
"
(25 mm)
39
" min.
(990 mm)
3
"
(76 mm)
3
"
(76 mm)
34
" min.
(864 mm)
48 in.2*
(310 cm
2
)
24 in.
2
*
(155 cm
2
)
1
"
(25 mm)
4
"
(102 mm)
311/2
"
(800 mm)
30
" min.
(762 mm)
30
" min.
(762 mm)
28
" min.
(710 mm)
Duet®Steam Washer
PRODUCT MODEL NUMBERS OVERALL DIMENSIONS
WFW9600T,
WFW9450W
Electrical: 120-volt, 60 Hz, AC-only,
15 or 20 amp fused electrical supply. A time-delay
fuse or circuit breaker and separate circuit is
recommended.
RECESSED AREA AND CLOSET INSTALLATIONS
For closet installation, with a door, the minimum ventilation
openings in the top and bottom of the door are required (view B).
Louvered doors with equivalent air ventilation openings are
acceptable.
Washer on Pedestal
Recommended installation spacing for
cabinet installation
For cabinet installation, with a door, the minimum
ventilation openings in the top are required.
A
A. Side view - closet or confined area
B. Closet door with vents
B
Undercounter Installation - Washer Only
Dimensions shown are the recommended spacing.
DRAIN SYSTEM OPTIONS
Standpipe drain system - wall or floor (view A & B)
The standpipe drain requires a minimum diameter standpipe of 2" (50 mm). The
minimum carry-away capacity can be no less than 17 gal. (64 L) per minute.
The top of the standpipe must be at least 30" (762 mm) high and no higher than
96" (2.4 m) from the bottom of
the washer.
Stacked Washer and Dryer
Laundry tub drain system (view A)
The laundry tub needs a minimum
20 gal. (76 L) capacity. The top of
the laundry tub must be at least
30" (762 mm) above the floor.
*Min. top and
bottom air
openings for
closet door.
**External exhaust
elbow requires
additional space.
***Wall, door and
floor molding may
require additional
spacing.
Floor drain system (view B)
The floor drain system requires a siphon break
that may be purchased separately.
The siphon break must be a minimum of 28"
(710 mm) from the bottom of the washer.
Additional hoses might be needed.
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
A
B
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
A
B
Ref. W10254043
05/2009
Loading...