Whirlpool WFE775H0HZ, WFE975H0HZ Installation Manual

INSTALLATION INSTRUCTIONS

30" (76.2 CM) FREESTANDING ELECTRIC RANGES

INSTRUCTIONS D’INSTALLATION POUR CUISINIÈRES

ÉLECTRIQUES AUTOPORTANTES DE 30" (76,2 cm)

INSTRUCCIONES DE INSTALACIÓN ESTUFAS ELÉCTRICAS

INDEPENDIENTES DE 30" (76,2 cm)

Table of Contents

RANGE SAFETY .............................................................................2

INSTALLATION REQUIREMENTS

Tools and Parts Location Requirements Electrical Requirements — U.S.A. Only Electrical Requirements - Canada Only

INSTALLATION INSTRUCTIONS

Unpack Range..............................................................................7

Install Anti-Tip Bracket Electrical Connection — U.S.A. Only

.............................................................................3

................................................................3

.................................................................8

.................................................3

.......................................5

.......................................7

...................................................7

...........................................9

Table des matières

SÉCURITÉ DE LA CUISINIÈRE EXIGENCES D’INSTALLATION

Outils et pièces Exigences d’emplacement Spéciﬁcations électriques – É.-U. seulement Spéciﬁcations électriques

INSTRUCTIONS D’INSTALLATION

Déballage de la cuisinière Installation de la bride antibasculement

...........................................................................18

...................................................17

...................................................18

.........................................................18

............................20

..........................................................21

.............................................22

..........................................................22

....................................23

Verify Anti-Tip Bracket Is Installed and Engaged Level Range Warming Drawer or Premium StorageDrawer Storage Drawer Oven Door Complete Installation Moving the Range

Raccordement électrique – É.-U. seulement Vériﬁer que la bride antibasculement est bien installée et

engagée ......................................................................................28

Réglage de l’aplomb de la cuisinière Tiroir-réchaud ou tiroir de remisage de qualité supérieure Tiroir de remisage Porte du four Terminer l’installation Déplacement de la cuisinière

................................................................................14

..........................................................................15

..................................................................................15

.................................................................15

......................................................................16

.........................................29

.......................................................................30

..............................................................................30

..................................................................30

.....................................................31

......................13

...........................14

.............................24

........29

Índice

SEGURIDAD DE LA ESTUFA.......................................................32

REQUISITOS DE INSTALACIÓN

Herramientas y piezas Requisitos de ubicación Requisitos eléctricos — EE. UU. únicamente Requisitos eléctricos – Solo en Canadá

INSTRUCCIONES DE INSTALACIÓN

Desempaque la estufa Instalación del soporte antivuelco

IMPORTANT:

Save for local electrical inspector's use.

IMPORTANT :

Conserver ces instructions à l’usage de l’inspecteur des installations électriques local.

IMPORTANTE:

Guarde para tener a disposición del inspector de electricidad local.

................................................................33

...............................................................37

.................................................33

.............................................................33

...........................35

....................................36

.........................................37

.............................................38

Conexión eléctrica — EE. UU. únicamente Veriﬁque que el soporte antivuelco esté instalado y

enganchado Nivelación de la estufa Cajón de calentamiento o cajón de

almacenamiento premium .........................................................44

Cajón de almacenamiento Puerta del horno Completar la instalación Cómo mover la estufa

...............................................................................43

...............................39

...............................................................44

.........................................................45

.........................................................................45

............................................................45

................................................................46

W11085337C

RANGE SAFETY

WARNING

Tip Over Hazard

A child or adult can tip the range and be killed.

Install anti-tip bracket to floor or wall per installation instructions.

Slide range back so rear range foot is engaged in the slot of the anti-tip bracket.

Re-engage anti-tip bracket if range is moved.

Do not operate range without anti-tip bracket installed and engaged.

Failure to follow these instructions can result in death or serious burns to children and adults.

Range Foot

Anti-Tip Bracket

To verify the anti-tip bracket is installed and engaged:

• Slide range forward.

• Look for the anti-tip bracket securely attached to floor or wall.

• Slide range back so rear range foot is under anti-tip bracket.

• See installation instructions for details.

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Tools needed

■ Tape measure

■ Flat-blade screwdriver

■ Phillips screwdriver

■ Level

■ Hammer

■ Hand or electric drill

■ Wrench or pliers

■ Marker or pencil

Parts supplied

Check that all parts are included.

■ 3 - 10-32 hex nuts (attached to terminal block)

■ 3 - Terminal lugs

A. Anti-tip bracket B. #12 x 15⁄8" (41 mm) screws (2)

■ Anti-tip bracket must be securely mounted to ﬂoor or wall.

Thickness of ﬂooring may require longer screws to anchor bracket to ﬂoor.

Parts needed

If using a power supply cord kit:

■ A UL listed power supply cord kit marked for use with

ranges. The cord should be rated at 250 volts minimum, 40 amps or 50 amps that is marked for use with nominal 1³⁄8" (3.5 cm) diameter connection opening and must end in ring terminals or open-end spade terminals with upturned ends.

■ A UL listed strain relief.

Check local codes. Check existing electrical supply. See the appropriate “Electrical Requirements” section.

It is recommended that all electrical connections be made by a licensed, qualiﬁed electrical installer.

■ Masking tape

■ 1/4" (6.4 mm) drive ratchet

■ 1/4" (6.4 mm) nut driver

■ 3/8" (9.5 mm) and 5/16"

(8 mm) nut driver

■ 1/8" (3.2 mm) drill bit

(for wood ﬂoors)

■ Tin snips or large wire

cutters (for cutting ground strap if necessary)

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

■ It is the installer’s responsibility to comply with installation

clearances speciﬁed on the model/serial rating plate. The model/serial rating plate is located on the frame behind a top corner of the door or either side of the drawer.

■ To eliminate the risk of burns or ﬁre by reaching over the

heated surface units, cabinet storage space located above the surface units should be avoided. If cabinet storage is to be provided, the risk can be reduced by installing a range hood or microwave hood combination that projects horizontally a minimum of 5" (12.7 cm) beyond the bottom of the cabinets.

■ Cabinet opening dimensions that are shown must be used.

Given dimensions are minimum clearances.

■ The anti-tip bracket must be installed. To install the anti-tip

bracket shipped with the range, see the “Install Anti-Tip Bracket” section.

■ Grounded electrical supply is required. See the appropriate

“Electrical Requirements” section.

IMPORTANT: To avoid damage to your cabinets, check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate, or sustain other damage. This oven has been designed in accordance with the requirements of UL and CSA International and complies with the maximum allowable wood cabinet temperatures of 194° (90°C).

Mobile Home Additional Installation Requirements

The installation of this range must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280). When such standard is not applicable, use the Standard for Manufactured Home Installations, ANSI A225.1/NFPA 501A or local codes.

Mobile home installations require:

■ When this range is installed in a mobile home, it must be

secured per the instructions in this document.

■ Four-wire power supply cord or cable must be used in a

mobile home installation. The appliance wiring will need to be revised. See the “Electrical Connection - U.S.A. Only” section.

Product Dimensions

NOTE: The model may look different than the one pictured.

A. 273/8" (69.5 cm) max. depth with handle B. 461/2" (118.1 cm) overall height (max.) with leveling legs

screwed all the way in*

C. 36" (91.4 cm) cooktop height (max.) with leveling legs screwed

all the way in* D. 297⁄8" (75.9 cm) width E. 255⁄16" (64.3 cm) depth - back of range to front of cooktop** F. Model/serial rating plate (located on the frame behind a top

corner of the door or either side of the drawer)

IMPORTANT: Range must be level after installation. Follow the instructions in the “Level Range” section. Using the cooktop as a reference for leveling the range is not recommended.

*Range can be raised approximately 1" (2.5 cm) by adjusting the leveling legs. **Front of door and drawer may extend further forward depending on styling.

Cabinet Dimensions

Cabinet opening dimensions shown are for 25" (64.0 cm) countertop depth, 24" (61.0 cm) base cabinet depth and 36" (91.4 cm) countertop height.

IMPORTANT: If installing a range hood or microwave hood combination above the range, follow the range hood or microwave hood combination installation instructions for dimensional clearances above the cooktop surface.

A freestanding range may be installed next to combustible walls with zero clearance.

A. 13" (33.0 cm) max. upper cabinet depth B. 30" (76.2 cm) min. opening width C. For minimum clearance to top of cooktop, see NOTE* D. 30

" (76.2 cm) min. opening width

E. Outlet - 8" (20.3 cm) to 22" (55.9 cm) from either cabinet,

" (14.0 cm) max. from ﬂoor

5¹⁄

F. Cabinet door or hinges should not extend into the cutout

* NOTE: 24" (61.0 cm) minimum when bottom of wood or

metal cabinet is covered by not less than 1/4" (6.4 mm) ﬂame retardant millboard covered with not less than No. 28 MSG sheet steel, 0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper.

30" (76.2 cm) minimum clearance between the top of the

cooking platform and the bottom of an uncovered wood or metal cabinet.

Electrical Requirements — U.S.A. Only

If codes permit and a separate ground wire is used, it is recommended that a qualiﬁed electrical installer determine that the ground path and wire gauge are in accordance with local codes.

Do not use an extension cord. Be sure that the electrical connection and wire size are adequate

and in conformance with the National Electrical Code, ANSI/ NFPA 70-latest edition and all local codes and ordinances.

A copy of the above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

WARNING: Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualiﬁed electrician or service technician if you are in doubt as to whether the appliance is properly grounded. Do not modify the power supply cord plug. If it will not ﬁt the outlet, have a proper outlet installed by a qualiﬁed electrician.

Electrical Connection

To properly install your range, you must determine the type of electrical connection you will be using and follow the instructions provided for it here.

Range must be connected to the pr oper electrical voltage and fr equency as speciﬁed on the model/serial rating plate. The model/serial rating plate is located on the frame behind a top corner of the door or either side of the drawer . Refer to the ﬁgures in “Pr oduct Dimensions” in the “Location Requirements” section.

This range is manufactur ed with the neutral terminal

connected to the cabinet. Use a 3-wire, UL Listed, 40 or 50 amp power supply cor d (pigtail) (see the following Range Rating chart). If local codes do not permit ground thr ough the neutral, use a 4-wire power supply cord rated at 250 V, 40 or 50 amps and investigated for use with ranges.

Range Rating* Speciﬁed Rating

of Power Supply Cord Kit and Circuit Protection

120/240 Volts 120/208 Volts Amps

8.8-16.5 KW 7.8 - 12.5 KW 40 or 50**

16.6-22.5 KW 12.6 - 18.5 KW 50

* The NEC calculated load is less than the total connected load

listed on the model/serial rating plate.

** If connecting to a 50 amp circuit, use a 50 amp rated cord

with kit. For 50-amp rated cord kits, use kits that specify use with a nominal 1³⁄8" (34.9 mm) diameter connection opening.

■ A circuit breaker is recommended.

■ The range can be connected directly to the circuit breaker

box (or fused disconnect) through ﬂexible or nonmetallic sheathed, copper, or aluminum cable. See the “Electrical Connection — U.S.A. Only” section.

■ Allow 2 to 3 ft (61.0 to 91.4 cm) of slack in the line so that the

range can be moved if servicing is ever necessary.

■

■ A UL listed conduit connector must be provided at each end

of the power supply cable (at the range and at the junction box).

■ Wire sizes and connections must conform with the rating of

the range.

■ The wiring diagram is located on the Tech Sheet.

■ The Tech Sheet is located on the back of the range inside a

clear plastic bag.

If connecting to a 4-wire system:

This range is manufactured with the ground connected to the neutral by a link. The ground must be revised so the green ground wire of the 4-wire power supply cord is connected to the cabinet. See the “Electrical Connection — U.S.A. Only” section.

Grounding through the neutral conductor is prohibited for new branch-circuit installations (1996 NEC); mobile homes; and recreational vehicles, or an area where local codes prohibit grounding through the neutral conductor.

When a 4-wire receptacle of NEMA Type 14-50R is used, a matching UL listed, 4-wire, 250 volt, 40 or 50 amp, range power supply cord (pigtail) must be used. This cord contains 4 copper conductors with ring terminals or open-end spade terminals with upturned ends, terminating in a NEMA Type 14-50P plug on the supply end.

The fourth (grounding) conductor must be identiﬁed by a green or green/yellow cover and the neutral conductor by a white cover. Cord should be Type SRD or SRDT with a UL listed strain relief and be at least 4 ft (1.22 m) long.

4-wire receptacle (14-50R)

The minimum conductor sized for the copper 4-wire power cord are:

40 amp circuit 2 No.-8 conductors 1 No.-10 white neutral 1 No.-8 green grounding

If connecting to a 3-wire system:

Local codes may permit the use of a UL listed, 3-wire, 250 V, 40 or 50 amp range power supply cord (pigtail). This cord contains 3 copper conductors with ring terminals or open-end spade terminals with upturned ends, terminating in a NEMA Type 10-50P plug on the supply end. Connectors on the appliance end must be provided at the point the power supply cord enters the appliance. This uses a 3-wire receptacle of NEMA Type 10-50R.

3-wire receptacle (10-50R)

Electrical Requirements - Canada Only

INSTALLATION INSTRUCTIONS

WARNING

Electrical Shock Hazard

Electrically ground range.

Failure to do so can result in death, fire, or electrical shock.

If codes permit and a separate ground wire is used, it is recommended that a qualiﬁed electrical installer determine that the ground path is adequate and wire gauge are in accordanc with local codes.

Be sure that the electrical connection and wire size are adequate and in conformance with CSA Standard C22.1, Canadian Electrical Code, Part 1 - latest edition, and all local codes and ordinances.

A copy of the above code standards can be obtained from:

Canadian Standards Association

178 Rexdale Blvd.

Toronto, ON M9W 1R3 CANADA

■ Check with a qualiﬁed electrical installer if you are not sure

the range is properly grounded.

Unpack Range

WARNING

Excessive Weight Hazard

Use two or more people to move and install range.

Failure to do so can result in back or other injury.

1. Remove shipping materials, tape, and ﬁlm from range.

2. Remove oven racks and parts package from inside oven.

3. Do not remove the shipping base at this time.

A. Shipping base

4. On Ranges Equipped with a Storage Drawer:

Remove the storage drawer. See the “Storage Drawer” section. Use a 1/4" (6.4 mm) drive ratchet to lower the rear leveling legs one-half turn. Use a wrench or pliers to lower front leveling legs one-half turn.

Range Ratings* Speciﬁed Rating of Power

120/240 Volts 120/208

8.8 - 16.5 KW

16.6 - 22.5 KW

The NEC calculated load is less than the total connected load

listed on the model/serial/rating plate.

**If connecting to a 50 amp circuit, use a 50 amp rated cord with

kit. For 50 amp rated cord kits, use kits that specify use with a

nominal 1³⁄

■ A time-delay fuse or circuit breaker is recommended.

■ This range is equipped with a CSA International Certiﬁed

Power Cord intended to be plugged into a standard 14-50R wall receptacle. Be sure the wall receptacle is within reach of range’s ﬁnal location.

Volts

7.8 -

12.5 KW

12.6 -

18.5 KW

" (34.9 mm) diameter connection opening.

Supply Cord Kit and Circuit Protection

Amps

40 or 50** 50

A. 1/4" (6.4 mm) drive ratchet B. Rear leveling leg

On Ranges Equipped with a Warming Drawer or Premium Storage Drawer:

On ranges equipped with a warming drawer or premium storage drawer, the rear legs cannot be accessed by removing the warming drawer or premium storage drawer. It will be necessary to adjust the rear legs from outside the range. Use wrench or pliers to lower the front and rear leveling legs one-half turn.

C. Wrench or pliers D. Front leveling leg

■ Do not use an extension cord.

A. Rear leveling leg B. Wrench or pliers C. Front leveling leg

Install Anti-Tip Bracket

WARNING

Floor Mounting

Tip Over Hazard

A child or adult can tip the range and be killed.

Install anti-tip bracket to floor or wall per installation instructions.

Slide range back so rear range foot is engaged in the slot of the anti-tip bracket.

Re-engage anti-tip bracket if range is moved.

Do not operate range without anti-tip bracket installed and engaged.

Failure to follow these instructions can result in death or serious burns to children and adults.

1. Remove the anti-tip bracket from where it is taped inside the

storage drawer or warming drawer.

2. Determine which mounting method to use: ﬂoor or wall.

If you have a stone or masonry ﬂoor, you can use the wall mounting method. If you are installing the range in a mobile home, you must secure the range to the ﬂoor.

3. Determine and mark centerline of the cutout space. The

mounting can be installed on either the left side or right side of the cutout. Position mounting bracket against the wall in the cutout so that the V-notch of the bracket is 129⁄16" (31.9 cm) from centerline as shown.

Rear position

Wall Mounting

5. Using the Phillips screwdriver, mount anti-tip bracket to

the wall or ﬂoor with the two #12 x 15⁄8" (41 mm) screws provided.

6. Move range close enough to opening to allow for ﬁnal

electrical connections. Remove shipping base, cardboard, or hardboard from under range.

7. Move range into its ﬁnal location, making sure rear leveling

leg slides into anti-tip bracket.

8. Move range forward onto shipping base, cardboard, or

hardboard to continue installing the range using the following installation instructions.

Front position

Diagonal (2 options)

Centerline

A. 129⁄16" (31.9 cm) B. Bracket V-notch

4. Drill two 1/8" (3 mm) holes that correspond to the bracket

holes of the determined mounting method. See the following illustrations.

Electrical Connection — U.S.A. Only

Power Supply Cord

1. Disconnect power.

2. Remove the terminal block cover screws located on the back

of the range. Pull the cover down and toward you to remove cover from range.

Direct Wire

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Use 8 gauge copper or 6 gauge aluminum wire.

Electrically ground range.

Failure to follow these instructions can result in death, fire, or electrical shock.

Remove the top 10-32 hex nut from each of the 3 terminal blocks and set aside.

A. Two mounting tabs each side B. Terminal block cover C. Hex-head screws

3. Depending on your model, remove the plastic tag holding

three 10-32 hex nuts from the middle post of the terminal block.

REMOVE PLASTIC TAG AND

PLACE NUTS ONTO THE BLOCKS

4. Add strain relief. Style 1: Power supply cord strain relief

■ Remove the knockout for the power supply cord.

■ Assemble a UL Listed strain relief in the opening.

A. UL Listed strain relief

■ Tighten strain relief screw against the power supply cord.

Style 2: Direct wire strain relief

3/8"

■ Remove the knockout as needed for the ﬂexible conduit

connection.

■ Assemble a UL listed conduit connector in the opening.

A. Removable retaining nut B. Conduit

■ Tighten strain relief screw against the ﬂexible conduit.

If your home has: And you will be

Go to Section:

connecting to:

3-wire direct A circuit breaker

box or fused

(1.0 cm)

(7.6 cm)

disconnect

3-wire connection: Direct wire

4-wire connection: Power Supply Cord

Use this method for:

■ New branch-circuit installations (1996 NEC)

■ Mobile homes

■ Recreational vehicles

■ In an area where local codes prohibit grounding through the

neutral

1. Part of metal ground strap must be cut out and removed.

5. Complete installation following instructions for your type of

electrical connection:

4-wire (recommended) 3-wire (if 4-wire is not available)

Electrical Connection Options

2. Use a Phillips screwdriver to remove the ground-link screw

from the back of the range. Save the ground-link screw and

A. Metal ground strap B. Discard C. Ground-link screw

the end of the ground link under the screw.

If your home has: And you will be

connecting to:

4-wire receptacle (NEMA type 14-50R)

A UL Listed,

250 volt minimum,

Go to Section:

4-wire connection: Power supply cord

3. Feed the power supply cord through the strain relief on the

cord/conduit plate on bottom of range. Allow enough slack to easily attach the wiring to the terminal block.

40 amp, range

power supply cord

4-wire direct A circuit breaker

box or fused

(1.0 cm)

(12.7 cm)

disconnect

4-wire connection: Direct wire

3-wire receptacle (NEMA type 10-50R)

A UL Listed,

250 volt minimum,

40 amp, range

power supply cord

3-wire connection: Power supply cord

A. Terminal block B. Ground-link screw C. UL listed strain relief D. Power supply cord wires

4. Use a Phillips screwdriver to connect the green ground wire

3/8"

from the power supply cord to the range with the groundlink screw and ground-link section. The ground wire must be attached ﬁrst.

5. Use 3/8" (9.5 mm) nut driver to connect the neutral (white)

wire to the center terminal block post with one of the 10–32 hex nuts.

2. Use 3/8" (9.5 mm) nut driver to connect the neutral (white)

wire to the center terminal block post with one of the 10–32 hex nuts.

A. 10–32 hex nut B. Ground-link screw C. Line 2 (red)

D. Green ground wire E. Neutral (center) wire F. Line 1 (black)

6. Connect line 2 (red) and line 1 (black) wires to the outer

terminal block posts with 10-32 hex nuts.

7. Securely tighten hex nuts. NOTE: For power supply cord replacement, use only a

power cord rated at 250 volts minimum, 40 amps or 50 amps

that is marked for use with nominal 1³⁄

" (3.5 cm) diameter connection opening, with ring terminals and marked for use with ranges.

8. Tighten strain relief screws.

9. Replace terminal block access cover.

3-wire connection: Power Supply Cord

Use this method only if local codes permit connecting chassis ground conductor to neutral wire of power supply cord.

1. Feed the power supply cord through the strain relief on the

cord/conduit plate on bottom of range. Allow enough slack to easily attach the wiring to the terminal block.

A. 10–32 hex nut B. Line 2 (red) C. Ground-link screw

D. Neutral (white) wire E. Line 1 (black)

3. Connect line 2 (red) and line 1 (black) wires to the outer

terminal block posts with 10-32 hex nuts.

4. Securely tighten hex nuts. NOTE: For power supply cord replacement, use only a

power cord rated at 250 volts minimum, 40 amps or 50 amps

that is marked for use with nominal 1³⁄

" (3.5 cm) diameter connection opening, with ring terminals and marked for use with ranges.

5. Tighten strain relief screws.

6. Replace terminal block access cover.

Direct Wire Installation: Copper or Aluminum Wire

This range may be connected directly to the fuse disconnect or circuit breaker box. Depending on your electrical supply, make the required 3-wire or 4-wire connection.

1. Strip outer covering back 3" (7.6 cm) to expose wires. Strip

the insulation back 3/8" (9.5 mm) from the end of each wire.

(1.0 cm)

(7.6 cm)

2. Allow enough slack in the wire to easily attach the wiring

terminal block.

3. Complete electrical connection according to your type of

electrical supply (4-wire or 3-wire connection).

4-wire Connection: Direct Wire

Use this method for:

A. Terminal block B. Ground-link screw C. UL listed strain relief D. Power supply cord wires - large opening

■ New branch-circuit installations (1996 NEC)

■ Mobile homes

■ Recreational vehicles

■ In an area where local codes prohibit grounding through the

neutral

1. Part of metal ground strap must be cut out and removed.

A B

A. Metal ground strap B. Discard C. Ground-link screw

2. Use a Phillips screwdriver to remove the ground-link screw

from the back of the range. Save the ground-link screw and the end of the ground link under the screw.

3. Pull the wires through the strain relief on bottom of range.

Allow enough slack to easily attach wiring to the terminal block.

Bare Wire Torque Speciﬁcations

Attaching terminal lugs to the terminal block - 20 lbs-in. (2.3 N-m)

Wire Awg Torque

8 gauge copper 25 lbs-in. (2.8 N-m) 6 gauge aluminum 35 lbs-in. (4.0 N-m)

5. Use a hex or Phillips screwdriver to connect the bare (green)

ground wire to the range with the ground-link screw and ground-link section. The ground wire must be attached ﬁrst and must not contact any other terminal.

6. Use 3/8" nut driver to connect the neutral (white) wire to the

center terminal block post with one of the 10–32 hex nuts.

A. Terminal block B. Ground-link screw C. Cord/conduit plate D. Bare (green) ground wire

E. Line 2 (red) wire F. Neutral (white) wire G. Line 1 (black) wire

4. Attach terminal lugs to line 1 (black), neutral (white), and

line 2 (red) wires. Loosen (do not remove) the setscrew on the front of the terminal lug and insert exposed wire end through bottom of terminal lugs. Securely tighten setscrew to torque as shown in the following Bare Wire Torque Speciﬁcations chart.

A. 10–32 hex nut B. Line 2 (red) C. Bare (green) ground wire D. Ground-link screw

E. Neutral (white) wire F. Line 1 (black) G. Terminal lug

7. Connect line 2 (red) and line 1 (black) wires to the outer

terminal block posts with 10-32 hex nuts.

8. Securely tighten hex nuts.

9. Replace terminal block access cover.

3-wire connection: Direct Wire

Use this method only if local codes permit connecting ground conductor to neutral supply wire.

1. Pull the wires through the conduit on cord/conduit plate on

bottom of range. Allow enough slack to easily attach the wiring to the terminal block.

A. Terminal lug B. Setscrew C. Line 2 (red) wire D. Neutral (white) wire E. Line 1 (black) wire

A. Terminal block B. Ground-link screw C. Cord/conduit plate

D. Line 2 (red) wire E. Bare (green) ground wire F. Line 1 (black) wire

2. Attach terminal lugs to line 2 (red), bare (green) ground, and

line 1 (black) wires. Loosen (do not remove) the setscrew on the front of the terminal lug and insert exposed wire end through bottom of terminal lugs. Securely tighten setscrew to torque as shown in the following Bare Wire Torque Speciﬁcations chart.

A. Terminal lug B. Setscrew C. Line 2 (red) wire D. Bare (green) ground wire E. Line 1 (black) wire

Bare Wire Torque Speciﬁcations

Attaching terminal lugs to the terminal block - 20 lbs-in. (2.3 N-m)

Verify Anti-Tip Bracket Is Installed

and Engaged

On Ranges Equipped with a Storage Drawer:

1. Remove the storage drawer. See the “Storage Drawer”

section.

2. Use a ﬂashlight to look underneath the bottom of the range.

3. Visually check that the rear range foot is inserted into the slot

of the anti-tip bracket.

On Ranges Equipped with a Warming Drawer or Premium Storage Drawer:

1. Place the outside of your foot against the bottom front of the

warming drawer or premium storage drawer, and grasp the lower right or left side of the control panel as shown.

NOTE: If your countertop is mounted with a backsplash, it may be necessary to grasp the range higher than is shown in the illustration.

Wire Awg Torque

8-gauge copper 25 lbs-in. (2.8 N-m) 6-gauge aluminum 35 lbs-in. (4.0 N-m)

3. Use 3/8" nut driver to connect the bare (green) ground wire

to the center terminal block post with one of the 10–32 hex nuts.

A. 10–32 hex nut B. Line 2 (red) C. Ground-link screw

D. Bare (green) ground wire E. Line 1 (black) F. Terminal lug

4. Connect line 2 (red) and line 1 (black) wires to the outer

terminal block posts with 10-32 hex nuts.

5. Securely tighten hex nuts.

6. Replace terminal block access cover.

2. Slowly attempt to tilt the range forward.

If you encounter immediate resistance, the range foot is engaged in the anti-tip bracket.

3. If the rear of the range lifts more than 1/2" (12.7 mm) off the

ﬂoor without resistance, stop tilting the range and lower it gently back to the ﬂoor. The range foot is not engaged in the anti-tip bracket.

IMPORTANT: If there is a snapping or popping sound when lifting the range, the range may not be fully engaged in the bracket. Check to see if there are obstructions keeping the range from sliding to the wall or keeping the range foot from sliding into the bracket. Verify that the bracket is held securely in place by the mounting screws.

4. Slide the range forward, and verify that the anti-tip bracket is

securely attached to the ﬂoor or wall.

5. Slide range back so the rear range foot is inserted into the

slot of the anti-tip bracket.

IMPORTANT: If the back of the range is more than 2" (5.1 cm) from the mounting wall, the rear range foot may not engage the bracket. Slide the range forward and determine if there is an obstruction between the range and the mounting wall. If you need assistance or service, refer to the “Assistance or Service” section of the Use and Care Guide, or the “Warranty” section of the User Instructions, for contact information.

6. Repeat steps 1 and 2 to ensure that the range foot is

engaged in the anti-tip bracket. If the rear of the range lifts more than 1/2" (12.7 mm) off

the ﬂoor without resistance, the anti-tip bracket may not be installed correctly. Do not operate the range without antitip bracket installed and engaged. Please reference the “Assistance or Service” section of the Use and Care Guide, or the “Warranty” section of the User Instructions, to contact service.

Level Range

Determine if you have AquaLift® Technology or Steam Clean by referring to the “Range Care” section of the User Instructions.

For Ranges with AquaLift® Technology or Steam Clean:

1. Place level on the oven bottom as indicated in one of the two

ﬁgures below depending on the size of the level. Check with the level: side to side and front to back.

2. If range is not level, pull range forward until rear leveling leg

is removed from the anti-tip bracket.

3. Follow the directions in Style 1 or Style 2, depending on the

style of drawer supplied with the range.

For Ranges without AquaLift® Technology or Steam Clean:

1. Place a standard ﬂat rack in the oven.

2. Place level on the rack and check levelness of the range, ﬁrst

side to side; then front to back.

Warming Drawer or Premium Storage

Drawer

(on some models)

Remove all items from inside the warming drawer or premium storage drawer, and allow the range to cool completely before attempting to remove the drawer.

To Remove:

1. Open the warming drawer or premium storage drawer to its

fully open position.

2. Using a ﬂat-blade screwdriver, gently loosen the warming

drawer or premium storage drawer from the glide alignment notch and lift up the drawer alignment tab from the glide.

A. Flat-blade screwdriver B. Drawer alignment tab C. Drawer glide notch

3. Repeat Step 2 on the other side. The warming drawer or

premium storage drawer is no longer attached to the drawer glides. Using both hands, pick up the warming drawer or premium storage drawer to complete the removal.

3. If range is not level, pull range forward until rear leveling leg

is removed from the anti-tip bracket.

4. Follow the directions in Style 1 or Style 2, depending on the

style of drawer supplied with the range.

Style 1: Ranges Equipped with a Storage Drawer:

Use a 1/4" (6.4 mm) drive ratchet, wrench or pliers to adjust leveling legs up or down until the range is level. Push range back into position. Check that rear leveling leg is engaged in the anti-tip bracket.

Style 2: Ranges Equipped with a Warming Drawer or Premium Storage Drawer:

Use a wrench or pliers to adjust leveling legs up or down until the range is level. Push range back into position. Check that rear leveling leg is engaged in the anti-tip bracket.

NOTE: Range must be level for satisfactory baking performance and best cleaning results using AquaLift® Technology and Steam Clean functions.

To Replace:

1. Align the forward drawer notches with the notches in the

drawer glides on both sides. Place the rear alignment tabs into the drawer glides on both sides.

A. Drawer alignment tab B. Drawer glide notch

2. Push the warming drawer or premium storage drawer in all

the way.

3. Gently open and close the warming drawer or premium

storage drawer to ensure it is seated properly on the glides on both sides.

Storage Drawer

(on some models)

The storage drawer can be removed. Before removing, make sure drawer is cool and empty.

To Remove:

1. Pull the storage drawer straight back to the drawer stop.

A. Drawer stop notch

2. Lift up the front of the drawer and pull the drawer out.

To Replace:

1. Lift up the front of the drawer and place the rear of the

drawer inside the range so that the drawer stop notch is behind the drawer glide.

2. Lower the drawer so that the edge of the slide rail drops into

the slot in the drawer glide.

3. Slowly push the drawer into the range.

3. Close the oven door as far as it will shut.

4. Lift the oven door while holding both sides.

Continue to push the oven door closed and pull it away from the oven door frame.

To Replace:

1. Insert both hanger arms into the door.

2. Open the oven door.

You should hear a “click” as the door is set into place.

3. Move the hinge levers back to the locked position. Check

that the door is free to open and close. If it is not, repeat the removal and installation procedures.

A. Engage drawer glide.

NOTE: When properly installed, the rear slides on the bottom of the drawer will engage the base rails and the drawer will not tip when items are placed in the drawer.

Oven Door

For normal range use, it is not suggested to remove the oven door. However, if removal is necessary, make sure the oven is off and cool. Then, follow these instructions. The oven door is heavy.

To Remove:

1. Open oven door all the way.

2. Pinch the hinge latch between two ﬁngers and pull forward.

Repeat on other side of oven door.

A. Hinge latch

Complete Installation

1. Check that all parts are now installed. If there is an extra

part, go back through the steps to see which step was skipped.

2. Check that you have all of your tools.

3. Dispose of/recycle all packaging materials.

4. Check that the range is level. See the “Level Range” section.

5. Use a mild solution of liquid household cleaner and warm

water to remove waxy residue caused by shipping material. Dry thoroughly with a soft cloth. For more information, read the “Range Care” section of the Use and Care Guide or User Instructions or User Instructions.

6. Read the “Range Use” section in the range Use and Care

Guide or User Instructions.

7. Plug power cord into appropriate outlet. Turn power on.

8. Turn on surface burners and oven. See the Use and Care

Guide or User Instructions for speciﬁc instruction on range operation.

If range does not operate, check the following:

■ Household fuse is intact and tight; or circuit breaker has not

tripped.

■ Range is plugged into a grounded outlet.

■ Electrical supply is connected.

IMPORTANT: If the range control displays an “F9” or “F9, E0” error code, the electrical outlet in the home may be miswired. Contact a qualiﬁed electrician to verify the electrical supply.

■ See the “Troubleshooting” section in the Use and Care Guide

or User Instructions.

When the range has been on for 5 minutes, check for heat. If range is cold, turn off the range and contact a qualiﬁed technician.

+ 33 hidden pages

Whirlpool WFE775H0HZ, WFE975H0HZ Installation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual