THANK YOU for purchasing this high-quality product. Register your range at www.whirlpool.com. In Canada, register your range
at www.whirlpool.ca.
For future reference, please make a note of your product model and serial numbers. These can be found on the label located
ontheupper right corner of the front frame.
Model Number __________________________________________Serial Number ___________________________________________
Para una versión de estas instrucciones en español, visite www.whirlpool.com.
Para referencia futura, tome nota de los números de modelo y de serie de su producto. Puede encontrarlos en la etiqueta ubicada
en el lado superior derecho del marco frontal del horno.
Table of Contents
RANGE SAFETY .............................................................................2
The Anti-Tip Bracket ....................................................................2
The range will not tip during normal use. However, the range can tip if you apply too much force or weight to the open door without the
anti-tip bracket fastened down properly.
WARNING
Tip Over Hazard
A child or adult can tip the range and be killed.
Verify the anti-tip bracket has been properly installed and engaged per installation instructions.
Re-engage anti-tip bracket if range is moved.
Do not operate range without anti-tip bracket installed and engaged.
Failure to follow these instructions can result in death or serious burns to children and adults.
To verify the anti-tip bracket is installed and engaged:
Anti-Tip
Bracket
Range Foot
State of California Proposition 65 Warnings:
WARNING: This product contains one or more chemicals known to the State of California to cause cancer.
WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other
reproductive harm.
• Slide range forward.
• Look for the anti-tip bracket securely attached to floor or wall.
• Slide range back so rear range foot is under anti-tip bracket.
• See installation instructions for details.
2
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electrical shock,
injury to persons, or damage when using the range, follow
basic precautions, including the following:
■ WARNING:
THE RANGE, THE RANGE MUST BE SECURED BY
PROPERLY INSTALLED ANTI-TIP DEVICES. TO CHECK
IF THE DEVICES ARE INSTALLED PROPERLY, SLIDE
RANGE FORWARD, LOOK FOR ANTI-TIP BRACKET
SECURELY ATTACHED TO FLOOR OR WALL, AND
SLIDE RANGE BACK SO REAR RANGE FOOT IS
UNDER ANTI-TIP BRACKET.
■ CAUTION: Do not store items of interest to children in
cabinets above a range or on the backguard of a range –
children climbing on the range to reach items could be
seriously injured.
■ Proper Installation – Be sure the range is properly installed
and grounded by a qualified technician.
■ Never Use the Range for Warming or Heating the Room.
■ Do Not Leave Children Alone – Children should not be left
alone or unattended in area where the range is in use.
They should never be allowed to sit or stand on any part of
the range.
Wear Proper Apparel – Loose-fitting or hanging garments
■
should never be worn while using the range.
User Servicing – Do not repair or replace any part of the
■
range unless specifically recommended in the manual. All
other servicing should be referred to a qualified technician.
■ Storage in or on the Range – Flammable materials should
not be stored in an oven or near surface units.
■ Do Not Use Water on Grease Fires – Smother fire or flame
or use dry chemical or foam-type extinguisher.
■ Use Only Dry Potholders – Moist or damp potholders on
hot surfaces may result in burns from steam. Do not let
potholder touch hot heating elements. Do not use a towel
or other bulky cloth.
■ DO NOT TOUCH SURFACE UNITS OR AREAS NEAR
UNITS – Surface units may be hot even though they are
dark in color. Areas near surface units may become hot
enough to cause burns. During and after use, do not touch,
or let clothing or other flammable materials contact surface
units or areas near units until they have had sufficient time
to cool. Among those areas are the cooktop and surfaces
facing the cooktop.
■ Use Proper Pan Size – The range is equipped with one or
more surface units of different size. Select utensils having
flat bottoms large enough to cover the surface unit heating
element. The use of undersized utensils will expose a
portion of the heating element to direct contact and may
result in ignition of clothing. Proper relationship of utensil to
burner will also improve efficiency.
■ Never Leave Surface Units Unattended at High Heat
Settings – Boilover causes smoking and greasy spillovers
that may ignite.
■ Make Sure Reflector Pans or Drip Bowls Are in Place –
Absence of these pans or bowls during cooking may
subject wiring or components underneath to damage.
TO REDUCE THE RISK OF TIPPING OF
■ Protective Liners – Do not use aluminum foil to line surface
unit drip bowls or oven bottoms, except as suggested in
the manual. Improper installation of these liners may result
in a risk of electric shock, or fire.
Glazed Cooking Utensils – Only certain types of glass,
■
glass/ceramic, ceramic, earthenware, or other glazed
utensils are suitable for range-top service without breaking
due to the sudden change in temperature.
■ Utensil Handles Should Be Turned Inward and Not Extend
Over Adjacent Surface Units – To reduce the risk of burns,
ignition of flammable materials, and spillage due to
unintentional contact with the utensil, the handle of a
utensil should be positioned so that it is turned inward, and
does not extend over adjacent surface units.
■ Do Not Soak Removable Heating Elements – Heating
elements should never be immersed in water.
■ Do Not Cook on Broken Cooktop – If cooktop should
break, cleaning solutions and spillovers may penetrate the
broken cooktop and create a risk of electric shock. Contact
a qualified technician immediately.
■ Clean Cooktop With Caution – If a wet sponge or cloth is
used to wipe spills on a hot cooking area, be careful to
avoid steam burn. Some cleaners can produce noxious
fumes if applied to a hot surface.
Use Care When Opening Door – Let hot air or steam
■
escape before removing or replacing food.
Do Not Heat Unopened Food Containers – Build-up of
■
pressure may cause container to burst and result in injury.
■ Keep Oven Vent Ducts Unobstructed.
■ Placement of Oven Racks – Always place oven racks in
desired location while oven is
cool. If rack must be moved
while oven is hot, do not let potholder contact hot heating
element in oven.
DO NOT TOUCH HEATING ELEMENTS OR INTERIOR
■
SURFACES OF OVEN – Heating elements may be hot even
though they are dark in color. Interior surfaces of an oven
become hot enough to cause burns. During and after use,
do not touch, or let clothing or other flammable materials
contact heating elements or interior surfaces of oven until
they have had sufficient time to cool. Other surfaces of the
appliance may become hot enough to cause burns – among
these surfaces are oven vent openings and surfaces near
these openings, oven doors, and windows of oven doors.
For self-cleaning ranges –
■ Do Not Clean Door Gasket – The door gasket is essential
for a good seal. Care should be taken not to rub, damage,
or move the gasket.
■ Do Not Use Oven Cleaners – No commercial oven cleaner
or oven liner protective coating of any kind should be used
in or around any part of the oven.
■ Clean Only Parts Listed in Manual.
■ Before Self-Cleaning the Oven – Remove broiler pan and
other utensils.
For units with ventilating hood –
■ Clean Ventilating Hoods Frequently – Grease should not
be allowed to accumulate on hood or filter.
■ When flambeing foods under the hood, turn the fan on.
SAVE THESE INSTRUCTIONS
3
FEATURE GUIDE
This manual covers several models. Your model may have some or all of the items listed. Refer to this manual or the Frequently Asked
Questions section of our website at www.whirlpool.com for more detailed instructions. In Canada, reference the Customer Service
section at www.whirlpool.ca.
WARNING
Food Poisoning Hazard
Do not let food sit in oven more than one hour before
or after cooking.
Doing so can result in food poisoning or sickness.
KeypadFeatureInstructions
CLOCKClockThe Clock uses a 12-hour cycle.
1. Check that the oven is off.
2. Press CLOCK.
3. Press the Temp/Time up or down arrow keypad to set the hours. Press CLOCK to switch
to the minutes. Press the Temp/Time up or down arrow keypad to set theminutes.
4. Press CLOCK or the Start keypad.
LIGHTOven cavity lightPress LIGHT to turn the light on and off.
TIMER SET/OFFOven timerThe Timer can be set in hours or minutes up to 9 hours and 59 minutes.
1. Press TIMER SET/OFF.
2. Press the Temp/Time up or down arrow keypad to set the length of time.
3. Press the Start keypad to begin the countdown. If enabled, end-of-cycle tones will sound
at end ofcountdown.
4. Press TIMER SET/OFF to cancel the Timer. Do not press the Cancel keypad because the
oven will turn off.
StartCooking startThe Start keypad begins any oven function. If the Start keypad is not pressed within 10
CancelRange functionThe Cancel keypad stops any function except the Timer, Warm Zone, and Oven Control
TEMP/TIMETemperature
andtime adjust
BAKEBaking and
roasting
seconds, a tone will sound and The Start keypad will blink until pressed or canceled. If Start is
not pressed within 30 seconds after pressing a keypad, the function is canceled and the
time of day is displayed.
Lockout.
The Temp/Time up and down arrow keypads are used to adjust time and
temperaturesettings.
1. Press BAKE.
2. Press the Temp/Time up or down arrow keypad until desired temperature is reached.
Atone will sound if the minimum or maximum temperature is reached.
3. Press the Start keypad.
4. To change the temperature, repeat Step 2. Press the Start keypad.
5. Press the Cancel keypad when nished.
4
KeypadFeatureInstructions
FROZEN BAKEPrepackaged
BROILBroiling1. Position cookware in the oven and close the oven door.
KEEP WARMHold warmFood must be at serving temperature before placing it in the warmed oven.
WARM ZONEWarming zonePress WARM ZONE to select the warming element on the cooktop. Press the Start keypad.
DELAY STARTDelayed startDelay Start is used to enter the starting time for an oven function with a delayed start.
COOK TIMETimed cookingCook Time allows the oven to be set to turn on at a certain time of day, cook for a set length
STEAM CLEANSteam cleaning
CONTROL LOCK
(Hold 3 sec)
food
cycle
Oven and
cooktop control
lockout
1. Position the food on a at rack in the oven on rack 3 or 4. See the “Positioning Racks and
Bakeware” section.
NOTE: Cook only one package of frozen food at a time when using Frozen Bake™
Technology.
2. Press FROZEN BAKE LASAGNA or PIZZA.
3. Press the Temp/Time up or down arrow keypad to set the temperature as recommended
on the food packaging.
4. Press COOK TIME.
5. Press the Temp/Time up or down arrow keypad to set the maximum cook time as
recommended on the food packaging.
6. Press the Start keypad. The range will calculate the best cook time based on the current
oven temperature.
NOTE: The cook time that appears in the display is the estimated required cook time as
calculated by the oven control. It may be different than the time you entered. A beep will
alert you to check the food’s doneness with at least 2 minutes remaining on the timer.
Follow the prompts on the display to select more time if desired.
7. Press the Start keypad to start the calculated time.
8. At the end of the cook time, a beep will alert you to check the food’s doneness. When
“End” is displayed and is ashing, you can add more time, if desired. Press the up or
down arrow keypad to set the time, then press START. If more time is not added, the bake
element will turn off.
NOTE: Pressing Cancel will exit the Frozen Bake™ cycle.
9. Press the Cancel keypad when nished.
2. Press BROIL.
3. Press the Temp/Time up or down arrow keypad until desired temperature is reached.
Atone will sound if the minimum or maximum temperature is reached.
4. Press the Start keypad.
5. To change the temperature, repeat Step 3 and press the Start keypad.
6. Press the Cancel keypad when nished.
1. Press KEEP WARM.
2. Press the Temp/Time up or down arrow keypad until desired temperature is reached. A
tone will sound if the minimum or maximum temperature is reached.
3. Press the Start keypad.
4. Press the Cancel keypad when nished.
Press WARM ZONE again to turn off the warming element.
Delay Startshould not be used for foods such as breads and cakes because they may
notbakeproperly.
To set a Timed Cook or a Delayed Timed Cook, see “Cook Time” section.
of time, and/or shut off automatically.
To set a Timed Cook or a Delayed Timed Cook, see “Cook Time” section.
See the “Steam Clean” section for more information and helpful tips for the Steam Clean
feature.
1. Remove all racks and accessories from the oven cavity.
2. Press STEAM CLEAN.
3. Add 12 oz (355 mL) of distilled or ltered water to the oven bottom.
4. Press the Start keypad.
After 50 minutes, “END” will appear in the display to signal the end of the cycle.
5. Press the Cancel keypad to clear the display.
6. Remove any excess water with a sponge or cloth and wipe down oven interior.
1. Check that the oven and cooktop are off.
2. Press and hold CONTROL LOCK for 3 seconds.
3. A tone will sound and a lock will be displayed.
4. Repeat to unlock. No keypads will function with the controls locked.
5
COOKTOP USE
WARNING
Fire Hazard
Turn off all controls when done cooking.
Failure to do so can result in death or fire.
The control knobs can be set to anywhere between Hi and Melt.
Push in and turn to setting.
■ To avoid scratches, do not slide cookware or bakeware across
the cooktop. Aluminum or copper bottoms and rough nishes
on cookware or bakeware could leave scratches or marks on
the cooktop.
■ Do not cook popcorn in prepackaged aluminum containers on
the cooktop. They could leave aluminum marks that cannot be
removed completely.
■ To avoid damage to the cooktop, do not allow objects that
could melt, such as plastic or aluminum foil, to touch any part
of the cooktop.
■ To avoid damage to the cooktop, do not use the cooktop as
acutting board.
■ Use cookware about the same size as the surface cooking
area. Cookware should not extend more than 1/2" (13 mm)
outside the area.
B
A
C
A. Surface cooking area
B. Cookware/canner
C. 1/2" (13 mm) maximum overhang
REMEMBER: When range is in use, the entire cooktop area
may become hot.
Ceramic Glass
The surface cooking area will glow red when an element is on.
Some parts of the surface cooking area may not glow red when an
element is on. This is normal operation. It will also randomly cycle
off and back on again, even while on High, to keep the cooktop
from extreme temperatures.
It is normal for the surface of light-colored ceramic glass to appear
to change color when surface cooking areas are hot. Asthe glass
cools, it will return to its original color.
Clean the cooktop after each use to help avoid scratches, pitting,
abrasions, and to condition the glass surface. Ceramic glass
cooktop cleaner and a cooktop scraper are also recommended
for stubborn soils. Do not use abrasive cleaners, cleaning pads,
orharsh chemicals for cleaning. The Cooktop Care Kit Part
Number 31605 contains all of the items needed to clean and
condition your ceramic glass cooktop. Refer to the “Range Care”
section for additional information.
IMPORTANT: To avoid permanent damage to the cooktop surface
and to make soils easier to remove, clean the cooktop after each
use to remove all soils.
■ Avoid storing jars or cans above the cooktop. Dropping
a heavy or hard object onto the cooktop could crack
thecooktop.
■ To avoid damage to the cooktop, do not leave a hot lid on
the cooktop. As the cooktop cools, air can become trapped
between the lid and the cooktop and the ceramic glass could
break when the lid is removed.
■ For foods containing sugar in any form, clean up all spills and
soils as soon as possible. Allow the cooktop to cool down
slightly. Then, while wearing oven mitts, remove the spills
using a scraper while the surface is still warm. If sugary spills
are allowed to cool down, they can adhere to the cooktop and
can cause pitting and permanent marks.
■ Use at-bottomed cookware for best heat conduction and
energy efciency. Cookware with rounded, warped, ribbed,
ordented bottoms could cause uneven heating and poor
cooking results.
■ Determine atness by placing the straight edge of a ruler
across the bottom of the cookware. While you rotate the
ruler, no space or light should be visible between it and
thecookware.
■ Cookware designed with slightly indented bottoms or small
expansion channels can be used.
■ Make sure the bottoms of pots and pans are clean and dry
before using them. Residue and water can leave deposits
when heated.
■ To avoid damage to the cooktop, do not cook foods directly
on the cooktop.
Ceramic Glass Cooktop Cleaning
Clean the cooktop after each use to help avoid scratches, pitting,
abrasions, and to condition the glass surface. Ceramic glass
cooktop cleaner and a cooktop scraper are also recommended
for stubborn soils. Do not use abrasive cleaners, cleaning pads, or
harsh chemicals for cleaning. The Cooktop Care Kit Part Number
31605 contains all of the items needed to clean and condition
your ceramic glass cooktop. Refer to the “Range Care” section for
additional information.
IMPORTANT: To avoid permanent damage to the cooktop surface
and to make soils easier to remove, clean the cooktop after each
use to remove all soils.
6
Cooktop On Indicator Light
The Cooktop On indicator light is located on the display panel.
When any cooktop element on the console panel is turned on,
theCooktop On indicator light will glow.
Hot Surface Indicator Light
On ceramic glass models, the Hot Surface indicator light is located
on the display panel.
The Hot Surface indicator light will glow as long as any surface
cooking area is too hot to touch, even after the surface cooking
area is turned off.
Dual Zone Cooking Element (on some models)
The Dual Zone cooking element offers exibility depending on the
size of the cookware. Single size can be used in the same way as
a regular element. The dual size combines both the single and
outer elements and is recommended for larger size cookware.
AB
A. Dual
B. Single
Melt Cooking Element (on some models)
The Melt cooking element offers exibility due to a wide range of
settings between HI and Melt. The HI heat option can be used to
boil small amounts of liquid quickly. The lowest setting can be
used to prepare sauces and to keep foods at a low temperature.
Use cookware appropriate in size for the Melt element.
AB
The Warm Zone area will not glow red when cycling on. However,
the Cooktop On indicator light will be displayed when the Warm
Zone is in use.
■ Use only cookware recommended for oven and cooktop use.
■ Cover all foods with a lid or aluminum foil. When warming
baked goods, allow a small opening in the cover for moisture
to escape.
■ To avoid damage to the cooktop, do not use plastic wrap
tocover food because the plastic wrap may melt.
■ Use pot holders or oven mitts to remove food.
To Use:
1. To turn on, press WARM ZONE andthenthe Start keypad.
2. To turn off, press WARM ZONE.
Cookware
IMPORTANT: Do not leave empty cookware on a hot surface
cooking area, element, or surface burner.
Ideal cookware should have a at bottom, straight sides, and a
well-tting lid, and the material should be of medium-to-heavy
thickness.
Rough nishes may scratch the cooktop. Aluminum and
coppermay be used as a core or base in cookware. However,
when used as a base, they can leave permanent marks on
thesurfaces.
Cookware material is a factor in how quickly and evenly heat
is transferred which affects cooking results. A nonstick nish
has thesame characteristics as its base material. For example,
aluminum cookware with a nonstick nish will take on the
properties of aluminum.
Cookware with nonstick surfaces should not be used under
thebroiler.
Check for atness by placing the straight edge of a ruler across
the bottom of the cookware. While you rotate the ruler, no space
or light should be visible between it and the cookware.
1
2
3
4
1
5
6
7
2
8
9
3
1 0
1 1
1 2
4
1 3
1 4
5
1 5
1 6
6
1 7
1 8
1 9
7
2 0
A. Melt option
B. Hi heat option
Warm Zone
WARNING
Food Poisoning Hazard
Do not let food sit in oven more than one hour before
or after cooking.
Doing so can result in food poisoning or sickness.
Use the cooktop Warm Zone to keep cooked foods warm. One
hour is the recommended maximum time to maintain food quality.
Do not use it to heat cold foods.
The Warm Zone can be used alone or when any of the other
surface cooking areas are being used.
7
Use the following chart as a guide for cookware material
characteristics.
CookwareCharacteristics
Aluminum■ Heats quickly and evenly.
■ Suitable for all types of cooking
■ Medium or heavy thickness is best
formost cooking tasks.
■ May leave aluminum residue which may
be diminished if cleaned immediately
after cooking.
Cast iron■ Heats slowly and evenly.
■ Good for browning and frying
■ Maintains heat for slow cooking.
■ Rough edges or burrs may scratch
thecooktop.
Ceramic or
ceramic glass
■ Follow manufacturer’s instructions.
■ Heats slowly, but unevenly.
■ Ideal results on low-to-medium heat
settings
■ May scratch the cooktop.
Copper■ Heats very quickly and evenly.
■ May leave copper residue which may be
diminished if cleaned immediately after
cooking.
■ Can leave a permanent stain or bond
tothe cooktop if overheated.
Earthenware■ Follow manufacturer’s instructions.
■ Use on low heat settings.
■ May scratch the cooktop.
Porcelain
enamel-on-steel
or castiron
■ See stainless steel or cast iron.
■ Porcelain enamel bakeware without the
metal base may bond to the cooktop if
overheated.
Stainless steel■ Heats quickly, but unevenly.
■ A core or base of aluminum or copper
on stainless steel provides even heating.
Use at-bottomed cookware for best cooking results and energy
efciency. The cookware should be about the same size as the
cooking area outlined on the cooktop. Cookware should not
extend more than 1/2" (13 mm) outside the area.
Home Canning
Canning can be performed on a glass smoothtop cooking surface
or traditional coil element cooktop. When canning for long periods,
alternate the use of surface cooking areas or elements between
batches. This allows time for the most recently used areas to cool.
■ Center the canner on the largest surface cooking area or
element. On electric cooktops, canners should not extend
more than 1/2" (13 mm) beyond the surface cooking area
orelement.
■ Do not place canner on two surface cooking areas or elements
atthe same time.
■ On ceramic glass models, use only at-bottomed canners
toavoid damage to the cooktop and elements.
■ For more information, contact your local agricultural extension
ofce or refer to published home canning guides. Companies
that manufacture home canning products can also offer
assistance.
8
OVEN USE
Odors and smoke are normal when the oven is used the rst few
times or when it is heavily soiled.
IMPORTANT: The health of some birds is extremely sensitive
tothe fumes given off. Exposure to the fumes may result in
deathto certain birds. Always move birds to another closed
andwell-ventilated room.
Electronic Oven Controls
Control Display
The display will ash when powered up or after a power loss.
Press the Cancel keypad to clear. When oven is not in use, the
time of day isdisplayed.
Fahrenheit and Celsius
The temperature is preset to Fahrenheit but can be changed
toCelsius.
To change: Press and hold the Temp/Time up arrow keypad for
5seconds. “°C”or“°F” will appear on the display. Repeat to
change back.
To exit mode, press the Cancel keypad.
Keypress Tones
Activates or turns off the tones when a keypad is pressed.
To change: Press and hold LIGHT for 5 seconds. Repeatto
change back.
To exit mode, press the Cancel keypad.
Demo Mode
IMPORTANT: This feature is intended for use on the sales oor
with 120 V power connection and permits the control features
to be demonstrated without heating elements turning on. If this
feature is activated, the oven will not work.
To change: Press the Cancel keypad, the Cancel keypad, the
Temp/Time up arrow keypad, TIMER SET/OFF. Repeat to change
back and end Demo mode.
Tones
Tones are audible signals, indicating the following:
Basic Functions
One Tone
■ Valid keypad press
■ Oven is preheated (long tone).
■ Function has been entered.
■ Reminder, repeating every 20 seconds after the end-of-cycle
tones
Three Tones
■ Invalid keypad press
Four Tones
■ End of cycle
Oven Temperature Control
IMPORTANT: Do not use a thermometer to measure oven
temperature. Elements will cycle on and off as needed to provide
consistent temperature but may run slightly hot or cool at any
point in time due to this cycling. Most thermometers are slow
to react to temperature change and will not provide an accurate
reading due to this cycling.
The oven provides accurate temperatures; however, it may cook
faster or slower than your previous oven, so the temperature can
be adjusted to personalize it for your cooking needs. It can be
changed in Fahrenheit or Celsius.
To Adjust Oven Temperature:
1. Press and hold the Temp/Time down arrow keypad for
5seconds until the ovendisplay shows the current setting,
forexample “0°FCAL” or “00.”
2. Press the Temp/Time up or down arrow keypad toincrease
or to decrease the temperature in 5°F (3°C) amounts. The
adjustment can be set between 30°F (18°C) and-30°F(-18°C).
3. Press the Start keypad.
Sabbath Mode
(on some models)
For guidance on usage and a complete list of models with
Sabbath mode, visit www.star-k.org.
The Sabbath mode sets the oven to remain on in a Bake setting
until turned off. A Timed Bake can also be set to keep the oven on
for only part of the Sabbath. The Oven Control Lockout feature will
be disabled during the Sabbath mode. After the Sabbath mode is
set, no tones will sound, the display will not show the temperature,
the Kitchen Timer mode will be canceled (ifactive), and only the
following keypads will function:
■ Temp/Time up and down arrow keypads
■ Cancel
When the oven door is opened or closed, the oven light will not
turn on or off and the heating elements will not turn on or off.
When power is restored after a power failure, the oven will return
to Sabbath mode and remain Sabbath compliant with the bake
elements off until the Cancel keypad is pressed.
Pressing the Cancel keypad at any time returns the oven to the
normal cooking mode (not Sabbath compliant).
Before entering the Sabbath mode, it must be decided if the oven
light is to be on or off for the entire Sabbath mode period. If the
light is on when entering Sabbath mode, it will remain on for the
entire time Sabbath mode is in use. If the light is off when entering
Sabbath mode, it will remain off for the entire time Sabbath mode
is in use. Opening the oven door or pressing LIGHT will not affect
the oven light once Sabbath mode has been entered.
On the Holiday, the oven temperature can be changed once the
oven is in Sabbath mode by pressing the Temp/Time up or down
arrow keypad. The oven temperature will change 25°F (14°C) each
time the Temp/Time up and down arrow keypads are pressed.
Press the Start keypad to activate the new temperature. The
display will not change and there will be no sounds during this
adjustment.
9
To Activate and Bake Using Sabbath Mode:
1. Press BAKE.
2. Press the Temp/Time up or down arrow keypad.
3. Press the Start keypad.
4. Press and hold TIMER SET/OFF for 5 seconds. “SAb” will ash
in the display.
5. Press the Start keypad while “SAb” is ashing to enter
Sabbath mode; otherwise, the entire cycle cancels out. “SAb”
will stop ashing and remain on in the display. The oven is now
in Sabbath mode and is Sabbath compliant.
Pressing the Cancel keypad at any time returns the oven to the
normal cooking mode (not Sabbath compliant).
NOTE: If “SAb” does not appear in your display, the Sabbath
mode is not active. After Sabbath mode is deactivated, you must
activate Sabbath mode by completing steps 1 through 5.
To Set a Timed Bake Using Sabbath Mode
(onsomemodels):
1. Press BAKE.
2. Press the Temp/Time up or down arrow keypad to enter
atemperature other than the one displayed.
3. Press COOK TIME. The Cook Time oven indicator light
willlight up.
4. Press the Temp/Time up or down arrow keypad to enter
acooktimelength.
5. Press the Start keypad.
6. Press and hold TIMER SET/OFF for 5 seconds. “SAb” will ash
in the display.
7. Press the Start keypad while “SAb” is ashing to enter
Sabbath mode; otherwise, the entire cycle cancels out. “SAb”
will stop ashing and remain on in the display. The oven is now
in Sabbath mode and is Sabbath compliant. The Bake, On,
andCook Time indicator lights will be displayed.
When the set cook time ends, the oven will shut off automatically
and the indicator lights will turn off, indicating the end of the cycle.
Pressing the Cancel keypad at any time returns the oven to the
normal cooking mode (not Sabbath mode compliant).
NOTE: If “SAb” does not appear in your display, the Sabbath
mode is not active. After Sabbath mode is deactivated, you must
activate Sabbath mode by completing steps 1 through 5.
To Set a Delayed Timed Bake Using Sabbath Mode
(onsome models):
WARNING
Food Poisoning Hazard
Do not let food sit in oven more than one hour before
or after cooking.
Doing so can result in food poisoning or sickness.
1. Press BAKE.
2. Press the Temp/Time up or down arrow keypad to enter
atemperature other than the one displayed.
3. Press COOK TIME. The Cook Time oven indicator light
willlight up.
4. Press the Temp/Time up or down arrow keypad to enter
acooktimelength.
5. Press DELAY START. The Delay indicator light will light up.
6. Press the Temp/Time up or down arrow keypad to enter astart
time.
7. Press the Start keypad.
8. Press and hold TIMER SET/OFF for 5 seconds. “SAb” will ash
in the display.
9. Press the Start keypad while “SAb” is ashing to enter
Sabbath mode; otherwise, the entire cycle cancels out. “SAb”
will stop ashing and remain on in the display. The oven is now
in Sabbath mode and is Sabbath compliant. The On and Delay
indicator lights will be displayed.
When the start time is reached, the Bake, On, and Cook Time
indicator lights will automatically turn on. When the set cook time
ends, the oven will shut off automatically and the indicator lights
will turn off, indicating the end of the cycle.
Pressing the Cancel keypad at any time returns the oven to the
normal cooking mode (not Sabbath mode compliant).
NOTE: If “SAb” does not appear in your display, the Sabbath
mode is not active. After Sabbath mode is deactivated, you must
activate Sabbath mode by completing steps 1 through 5.
Keep Warm
WARNING
Food Poisoning Hazard
Do not let food sit in oven more than one hour before
or after cooking.
Doing so can result in food poisoning or sickness.
IMPORTANT: Food must be at serving temperature before placing
it in the warmed oven. Food may be held up to 1 hour; however,
breads and casseroles may become too dry if left in the oven
during the Keep Warm function. For best results, coverfood.
The Keep Warm feature allows hot cooked foods to stay at
servingtemperature.
To Use:
1. Press KEEP WARM.
2. Press the Temp/Time up or down arrow keypad until desired
temperature is reached. A tone will sound if the minimum or
maximum temperature is reached.
3. Press the Start keypad.
4. Place food in the oven.
5. Press the Cancel keypad when nished.
NOTE: The temperature may be changed at any time by pressing
the Temp/Time up or down arrow keypad to reach the desired
temperature and then pressing the Start keypad.
10
Aluminum Foil
IMPORTANT: To avoid permanent damage to the oven bottom
nish, do not line the oven bottom with any type of foil or liner.
For best cooking results, do not cover entire oven rack with foil
because air must be able to move freely.
Positioning Racks and Bakeware
IMPORTANT: To avoid permanent damage to the porcelain
nish, do not place food or bakeware directly on the oven door
orbottom.
Bakeware
To cook food evenly, hot air must be able to circulate. Allow
2"(5cm) of space around bakeware and oven walls. Make
surethatno bakeware piece is directly over another.
Racks
■ Position racks before turning on the oven.
■ Do not position racks with bakeware on them.
■ Make sure racks are level.
To move a rack, pull it out to the stop position, raise the front
edge, and then lift out. Use the following illustration asa guide.
5
4
3
2
1
The oven has seven positions for a at rack, as shown in the
previous illustration and the following table.
Baking Cookies and Layer Cakes on Two Racks
Baking Layer Cakes
For best results when baking cakes on two racks, use the Bake
function, a at rack in rack position 4, and a at rack in rack
position 2. Place the cakes on the racks as shown. Keep at least
3" (7.6 cm) of space between the front of the racks and the front
cakes.
Baking Cookies on Two Racks
For best results when baking cookies on two racks, use the Bake
function and place at racks in positions 2 and 5.
Oven Vent
A
A. Oven vent
The oven vent releases hot air and moisture from the oven
andshould not be blocked or covered. Blocking or covering the
oven vent will cause poor air circulation, affecting cooking and
cleaning results. Do not set plastics, paper, or other items that
could melt or burn near the oven vent.
Flat Rack PositionType of Food
5Broiling/searing meats, hamburgers,
steaks, or toast.
4Broiling thicker cuts of meat, poultry, sh
3 or 4Frozen prepackaged foods, most baked
goods, and casseroles.
1 or 2Large roasts or poultry
Multiple Rack Cooking
Two-rack: Use rack positions 2 and 4 or 2 and 5.
Baking and Roasting
Preheating
When beginning a Bake cycle, the oven will begin preheating
after Start is pressed. The oven will take approximately 12 to
15 minutes to reach 350°F (177°C) with all of the oven racks
provided with your oven inside the oven cavity. Higher
temperatures will take longer to preheat. The preheat cycle
rapidly increases the oven temperature. The actual oven
temperature will go above your set temperature to offset the heat
lost when your oven door is opened to insert food. This ensures
that when you place your food in the oven, the oven will begin at
the proper temperature. Insert your food when the preheat tone
sounds. Do not open the door during preheat before the tone
sounds.
Oven Temperature
While in use, the oven elements will cycle on and off as needed
to maintain a consistent temperature, but they may run slightly
hot or cool at any point in time due to this cycling. Opening the
oven door while in use will release the hot air and cool the oven
which could impact the cooking time and performance. It is
recommended to use the oven light to monitor cooking progress.
Temperature Management System
The Temperature Management System electronically regulates the
oven heat levels during preheat and bake to maintain a precise
temperature range for optimal cooking results. The bake and broil
elements or burners cycle on and off in intervals. On convection
range models, the fan will run while preheating and may be cycled
on and off for short intervals during bake to provide the best
results. This feature is automatically activated when the oven is
in use.
11
Before baking and roasting, position racks according to the
WARNING
“Positioning Racks and Bakeware” section. When roasting, it is
not necessary to wait for the oven preheat cycle to end before
putting food in unless it is recommended in the recipe.
Broiling
When broiling, preheat the oven for two minutes before putting
food in unless recommended otherwise in the recipe. Position
food on grid in a broiler pan, then place it in the center of the oven
rack.
IMPORTANT: Close the door to ensure proper broiling
temperature.
Changing the temperature when broiling allows more precise
control when cooking. The lower the broil setting is, the slower the
cooking. Thicker cuts and unevenly shaped pieces of meat, sh,
and poultry may cook better at lower broil settings. Use racks 4
or 5 for broiling. Refer to the “Positioning Racks and Bakeware”
section for more information.
On lower settings, the broil element will cycle on and off to
maintain the proper temperature.
■ For best results, use a broiler pan and grid. It is designed to
drain juices and help avoid spatter and smoke.
If you would like to purchase a broiler pan, one may be
ordered. Please refer to the “Accessories” section for
moreinformation.
NOTE: Odors and smoke are normal the rst few times the oven
isused or if the oven is heavily soiled.
Cook Time
Food Poisoning Hazard
Do not let food sit in oven more than one hour before
or after cooking.
Doing so can result in food poisoning or sickness.
To Set a Timed Cook:
1. Press BAKE. The Bake indicator light will light up.
2. Press the Temp/Time up or down arrow keypad to enter
atemperature other than the one displayed.
3. Press COOK TIME. The cook time oven indicator light will
lightup.
4. Press the Temp/Time up or down arrow keypad to enter the
length of time to cook.
5. Press the Start keypad. The display will count down the time.
When the time ends, the oven will shut off automatically.
6. Press the Cancel keypad to clear the display.
To Set a Delayed Timed Cook:
Before setting, make sure the clock is set to the correct time
of day. See the “Clock” keypad feature in the “Feature Guide”
section.
1. Press BAKE.
2. Press the Temp/Time up or down arrow keypad to enter
atemperature other than the one displayed.
3. Press COOK TIME. The cook time oven indicator light will
lightup.
4. Press the Temp/Time up or down arrow keypad to enter
thelength of time to cook.
5. Press DELAY START. The delay oven indicator light will light
up.
6. Press the Temp/Time up or down arrow keypad to enter
thetime of day to start.
7. Press the Start keypad.
When the start time is reached, the oven will automatically turn
on. The temperature and/or time settings can be changed anytime
after pressing the Start keypad by repeating steps 1 through 7.
When the set cook time ends, the oven will shut off automatically.
8. Press the Cancel keypad to clear the display.
RANGE CARE
Steam Clean
IMPORTANT: Do not use oven cleaners or any other additives with
Steam Clean.
The Steam Clean feature is designed for light oven cavity bottom
cleaning and is not intended to clean heavy or difcult soils. Use
the Steam Clean feature as soon as possible after spills occur. The
longer a spill sits and dries in the oven, the more difcult it may be
to remove.
Allow the range to cool to room temperature before using the
Steam Clean feature. If your oven cavity is above 170°F (77°C),
“HOT” will appear in the display and the Steam Clean feature will
not activate until it cools down.
■ Remove all racks and accessories from the oven cavity.
■ For best results, pour 12 oz (355 mL) of distilled or ltered
water onto the oven bottom.
■ The Steam Clean feature will take a total of 50 minutes. “End”
will appear in the display at the end of the cycle.
IMPORTANT: Since the water in the oven bottom is hot, do not
open the oven door during the Steam Clean cycle.
Press the Cancel keypad at any time to end the cycle. The display
will return to the time of day.
Helpful Hints
■ Once the Steam Clean cycle is complete, remove all remaining
water and debris in the bottom of the oven with a sponge or
cloth.
■ Wipe any remaining moisture from the oven door interior, oven
cavity interior sides, and cooktop.
■ Use a soft brush or nylon scrubber to wipe the oven interior.
This may help with more stubborn stains.
■ If any soil remains, run a second Steam Clean cycle to help
loosen debris for easier removal.
■ Use the Steam Clean on small spills such as cheese or sauce
from pizza or snacks, or drips from casseroles.
■ Food spills containing sugar, proteins, or starches may require
vigorous scrubbing to remove most of the debris.
■ It is recommended to use distilled or ltered water, as tap
water may leave mineral deposits on the oven bottom. Use a
cloth soaked with vinegar or lemon juice to remove any mineral
deposits that may be left after the Steam Clean cycle.
12
Loading...
+ 28 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.