Whirlpool WAECO 8770 BK, WAECO 8766 BK INSTRUCTION FOR USE
40105514GB.fm Page 1 Tuesday, October 27, 2009 4:44 PM
GB PROGRAMME CHART
A. Programme selector
B. Display
C. “Temperature” button
D. “Variable spin” button
E. “Start delay” button
F. “Start (Pause)” button
G. “Reset/Drain” button
H. “Favourites” button
Programme
White Cotton /
Hygienic +
Cotton
Coloured
Kulørt
Tempe-
rature
Care
Max.
Load
Labels
kg
70 - 95 °C 8.0
20 - 60 °C
8.0
J M
L
K
C
Type of wash/Notes
- Respect the manufacturer’s recommendations on the care label
Normally to heavily soiled bed linen, table linen and underwear, towels, shirts etc. made of
cotton and linen.
At a temperature of 80°C or more, this programme eliminates bacteria, ensuring
sanitization of your laundry. The bacteria removal efficiency has been tested following a
similar methodology to the NF EN 13697 standard of Nov. 2001.
I
}
B
E
DH
I. Programme sequence indication
J. “Door open” indication
G
K. “Child lock” indication
L. “Detergent overdosage” indication
A F
Detergents and additives Selectable options Start delay
Pre-
Main
wash
❉
Softener Clean +
wash
Yes
Clean +
❉❉❉❉❉ ❉ ❉
M. Red failure indications
Pre-
Rinse
wash
Forvask
hold
Skylle-
stop
Intensive
rinse
Ekstra
skyl
Udskudt
start
Variable
spin
Centr.
Spin
Max
Spin
Speed
rpm
max.
Synthetics Syntetisk
Delicates Skåneprogram
Wool Uld
Handwash Håndvask
Lingerie Lingeri
Eco Cotton Øko-bomuld
Sport Sport
Super Eco SuperEco
Daily load Dagligvask
Speed 15 Quick vask 15’
Rinse & Spin
Spin Centrifugering
❉
optional / Yes : dosing required
:
1)
For improved garment care, spin speed is restricted in these programmes.
Skyl &
Centrifugering
20 - 60 °C
20 - 40 °C
20 - 40 °C 2.0
20 - 40 °C 2.0
20 - 30 °C 2.0
60 °C 8.0
20 - 30 °C
20 - 60 °C 8.0
20 - 60 °C
20 - 30 °C 3.0
——
——
Normally soiled blouses, shirts, overalls etc. made of polyester (Diolen, Trevira),
3.5
polyamide (Perlon, Nylon) or blends with cotton.
Curtains and delicate clothing, dresses, skirts, shirts and blouses.
2.5
Only woollens, labelled with the Woolmark and identified as machine washable.
This programme (40°C) is tested and approved by The Woolmark Company for machine
washable wool.
Textiles made of silk, linen, wool and viscose marked as “handwashable”.
This programme (40°C) is tested and approved by The Woolmark Company for
handwashable wool.
This programme is particularly suitable to treat delicate lingerie (use of a laundry net
strongly recommended).
Heavily soiled and robust laundry washable at 60°C such as bed linen, table linen, towels etc.
The extended programme duration enables economic energy and water consumption while
maintaining good washing results.
Normally soiled and sweaty sportswear made of cotton jersey or microfibers.
This programme includes a prewash cycle – you can add detergent also to the prewash
3.5
chamber. Do not add any softener.
Normally to heavily soiled and robust bed linen, table linen and underwear, towels, shirts
etc. made of cotton and linen.
Offers highest economy in energy consumption by prolonged washing duration. Ideal to be run
overnight to additionally profit from the more favourable energy rates. To avoid noise of spinning
at night, set spin speed to “0” and start spin programme in the morning, or define programme
start with “Start delay” accordingly.
Slightly to normally soiled textiles made of cotton and/or synthetics.
6.0
Refreshes briefly worn outer clothing made of cotton, artificial fibers and blends with
cotton. Use lowest recommended detergent amount.
Same as the last rinse and the final spin in the “Cotton” programme.
8.0
In this programme spinning is intensive. Same as the spin cycle in the “Cotton” programme.
8.0
The wool and handwash cycles of this machine have been tested and approved by The Woolmark Company for the washing of
Woolmark garments labelled as “machine wash” or “hand wash” provided that the garments are washed according to the
instructions on the garment label and those issued in this programme chart. M0702
Yes
❉
❉
—
—
—
—
❉
—
—
—
——
❉❉❉❉❉ ❉ ❉
Yes
Yes
Yes
Yes
Yes
Yes
———
Yes
Yes
Yes
❉
❉
❉
❉
❉
❉
❉
❉
❉
—
❉❉
——
——
——
——
——
——
——
——
—
—
❉
—
❉
—
❉
❉❉ ❉ ❉
❉❉ ❉ ❉
❉❉ ❉ ❉
❉❉ ❉ ❉
—
❉
❉❉ ❉ ❉
—— — — — — —
max.
❉❉
❉❉
❉❉
❉❉
❉❉
❉❉
1000
1000
400
400
max.
max.
max.
max.
max.
max.
max.
1)
1)
5019 401 05514
1)
1)
Black process 45.0° 150.0 LPI
40105514GB.fm Page 2 Tuesday, October 27, 2009 4:44 PM
The Sensor Technology automatically adapts Programme Time, Water and Energy consumption to the size of your wash load.
CONSUMPTION DATA
Programme
Temp e r ature
(°C)
White Cotton / Hygiene + 95 8.0 82
Cotton Coloured 60 8.0 59 1.36 2:20
Cotton Coloured 40 8.0 77 0.75 2:05
Synthetics 60 3.5 46
Synthetics 40 3.5 42 0.50 1:20
Delicates 30 2.5 60 0.40 0:45
Wool 40 2.0 60 0.60 0:45
Handwash 40 2.0 45 0.60 0:40
Lingerie 30 2.0 45 0.35 0:36
Eco Cotton
***
60 8.0 59 1.04 4:00
Sport 30 3.5 54 0.55 1:34
Super Eco 60 8.0 75 0.95 4:00
Daily load 40 6.0 73 0.60 1:00
Speed 15 30 3.0 30 0.20 0:15
Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home
may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.
The time indicated on the display can deviate from the values in the table, because it takes into account the operation conditi ons
*
applicable at that time.
To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
**
Reference Programme for Energy Label (with separator in detergent dispenser removed for use of powder detergent).
***
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
Add detergent as indicated on the front page and as described in
the chapter “Detergent and Additives” in your Instructions for Use
(remove separator in detergent dispenser for use of powder
detergent if necessary).
Turn the programme selector to the desired programme; the light
of the
“Start (Pause)”
indicated on the display can be altered by pressing the
speed
“Temperature” button or the “Variable spin” button.
button blinks. The
temperature
SELECT ANY DESIRED OPTION
When the combination of programme and additional option(s) is
not possible, the indication lights switch off automatically.
Unsuitable combinations of options are deselected automatically.
“Clean+” button
• Choose this option if you use an in-wash additive for stain removal
(powder , for example “Vanis h”) - it will optimize the additive’s
efficiency to get better wash performance and stain removal.
• Choose temperature of 30 or 40°C and use with maximum load.
• Add an appropriate amount of in-wash additive for stain
removal (powder) to the main wash chamber, together with
your detergent (only use powder detergent with this option).
Respect the manufacturer’s dosing instructions.
• Prolongs the programme by approx. 10 to 15 minutes.
• Appropriate for use of stain removers and bleaches on oxygen
basis.
Chlorine or perborate bleaches must not be used!
“Prewash” button
• Only for heavily soiled loads (for example sand, granular dirt)
sensible. Increases the cycle time by approximately 15 min.
• Do not use liquid detergent for the main wash when activating
the “Prewash” option.
and
Load
Water
(kg)
spin
(l)
(kWh)
2.40 2:20
**
0.85 1:35
**
“Rinse hold” button
• The laundry remains in the last rinse water, without
progressing to the fnal spin cycle, to avoid creasing and
prevent colours from changing.
• The programme stops to “Rinse hold” when the “Rinse hold”
symbol on the display blinks; the light of the
button blinks as well.
(Pause)”
• To terminate the “Rinse hold” by draining the water, without
any spinning, press the
• To terminate the “Rinse hold” by spinning the laundry, press
the "Variable spin" button to select the desired spin speed and
then
“Start (Pause)”
• Do not leave the laundry to soak for too long in the “Rinse hold”.
“Intensive rinse” button
• More water is added and rinse cycle is prolonged.
• This option is particularly suitable for areas with very soft water or
for washing baby linen, and helps people with allergies.
“Variable spin” button
• Every programme has a predefined spin speed.
• Press the button to set another spin speed.
• If spin speed “0” is selected, the final spinning is cancelled but
intermediate spin peaks remain during rinse. The water is
drained out only.
Energy
Approx. Programme Duration
(hours : minutes)
“Start (Pause)”
to start the spin cycle.
SAVE YOUR FAVOURITE PROGRAMMES
If there is a programme setting which you use frequently, the
appliance offers the possibility to save one setting for each
programme so that it can be used again by just pushing one button.
• Select the desired programme, temperature, spin speed and
option(s), push and hold the
seconds. The lamp of the
then lights up - the programme setting is saved.
“Favourites”
“Favourites”
button shortly blinks and
*
“Start
button.
button for at least 3
Next time you want to use your individual programme setting,
select the programme, shortly push the
start by pushing
If you want to replace the saved programme setting by another
one, proceed as already described above.
“Start (Pause)”
“Favourites”
.
button and
START DELAY
The “Start delay” allows to run the machine at the consumer’s
convenience, for example at night when electricity is cheaper. Do
not use liquid detergent when activating the “Start delay”.
• Select programme, temperature, spin speed and options.
• Press the Start delay button to select one of the delay time
steps between 0:30 and 23:00 hours.
•Press the
• The time delay indication disappears when the programme
To cancel the “Start delay”
..before you press the “Start (Pause)” button:
• Press the
..after having pressed the “Start (Pause)” button:
Press the
from the display; press
programme immediately.
“Start (Pause)”
becomes solid.
The countdown of the delay time begins; the clock symbol next to
the delay time and the colon between hours and minutes blink.
starts and it is replaced by the remaining programme time.
“Reset/Drain”
“0:00” - the delay time disappears after a few secon ds.
“Start (Pause)”
button; the light stops blinking and
button, or set the start delay time to
button - the delay time disappears
“Start (Pause)”
again to start the selected
“DOOR OPEN” INDICATION
Before starting and after end of a programme, the symbol lights to
show that the door can be opened. As long as a wash programme is
running, the door remains locked and must on no account be forced
open. In case you have to open it urgently during a running
programme, refer to “Reset a running programme before the end”.
PROGR AMME START
Open the tap and press the
“Start (Pause)”
sequence indicator shows the current programme phase, running
from left to right through wash, rinse, spin, drain. In some phases, the
remaining programme time is newly calculated - if this is the case, the
“green intelligence sensor” on the display will fade,
and the remaining time is replaced by an animation.
“Start (Pause)”
button light becomes constant. The programme
button; the blinking
CHILD LOCK
Activating the child lock prevents children from starting a wash
cycle or changing the settings of a running programme. The child
lock cannot be activated or deactivated when the programme
selector is in the “Off/O” position. To activate the child lock:
• Turn the programme selector to a programme position, or run
a programme as usual.
• Press the “Temperature” and the “Variable spin” button
simultaneously for at least 3 seconds. The “Child lock” symbol
will shortly blink and then light up to indicate that the
child lock is active.
The programme setting cannot be changed anymore; the only change
possible is to switch the washer off by turning the programme selector
to the “Off/O” position. To deactivate the child lock, proceed in the
same way as for activating it.
RED FAILURE INDICATIONS
If one of the red failure indications on the display lights up, refer to
the “Troubleshooting Guide” in your “Instructions for Use”.
PROGRAMME END
• The display shows “End”, and the “Door open” indication
lights up.
1. Turn the programme selector to the “Off/O” position.
2. Close the water tap.
3. Open the door and unload the machine.
• Leave the door ajar to allow the drum to dry.
• If you do not turn the programme selector to the “Off / O”
position, all lights of the control panel go out after a few minutes
to save energy - only “End” will remain on the display.
DETERGENT OVERDOSAGE INDICA TION
The symbol will light up at the end of the programme if you used
too much detergent. Use less detergent next time. If the symbol
lights up and the display shows “Fod”, too much foam interrupted
the wash process; refer to the “Troubleshooting Guide” in your
Instructions for Use.
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
1. Press the
2. Select the new programme, temperature, any options and
3. Press the
“Start (Pause)”
The light blinks.
another spin speed if you want.
“Start (Pause)”
continues at the same position where the previous programme was
interrupted. Do not add detergent for this programme.
button to pause the programme.
button again. The new programme
RESET A RUNNING PROGRAMME BEFORE
THE END
The
“Reset/Drain”
•Press the
animation appears on the display. Any existing water is drained
out before the door can be opened.
button cancels a programme before the end.
“Reset/Drain”
button for at least 3 seconds; an
5019 401 05514
Black process 45.0° 150.0 LPI
Loading...