Whirlpool W10112488 User Manual

WASHER INSTALLATION INSTRUCTIONS

INSTRUCCIONES PARA LA INSTALACIÓN DE LA LAVADORA

INSTRUCTIONS POUR L’INSTALLATION DE LA LAVEUSE

Table of Contents / Índice / Table des matières

WASHER SAFETY............................................ 1

INSTALLATION REQUIREMENTS ................. 2

Tools and Parts ............................................. 2

Location Requirements................................. 3

Drain System................................................. 3

Electrical Requirements ................................ 4

INSTALLATION INSTRUCTIONS ................... 4

Before You Start............................................ 4

Remove Shipping Materials.......................... 4

Connect Drain Hose...................................... 6

Connect the Inlet Hoses ............................... 6

Secure the Drain Hose.................................. 7

Level the Washer........................................... 7

Complete Installation .................................... 8

SEGURIDAD DE LA LAVADORA.................... 9

REQUISITOS DE INSTALACIÓN .................... 9

Herramientas y piezas................................... 9

Requisitos de ubicación.............................. 10

Sistema de desagüe ................................... 10

Requisitos eléctricos................................... 11

INSTRUCCIONES DE INSTALACIÓN .......... 12

Antes de empezar....................................... 12

Cómo quitar el material de transporte........ 12

Cómo conectar la manguera de desagüe..13

Conecte las mangueras de entrada ........... 13

Asegure la manguera de desagüe.............. 14

Nivele la lavadora........................................ 15

Complete la instalación............................... 16

SÉCURITÉ DE LA LAVEUSE......................... 16

EXIGENCES D’INSTALLATION .................... 17

Outillage et pièces....................................... 17

Exigences d’emplacement ......................... 18

Système de vidange ................................... 18

Spécifications électriques........................... 19

INSTRUCTIONS D’INSTALLATION.............. 19

Avant de commencer.................................. 19

Retrait du matériel d'expédition.................. 19

Raccordement du tuyau de vidange .......... 21

Raccordement des tuyaux

d’arrivée d’eau ............................................ 21

Immobilisation du tuyau de vidange........... 22

Réglage de l’aplomb de la laveuse............. 23

Achever l’installation................................... 24

WASHER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

You can be killed or seriously injured if you don't immediately

DANGER

WARNING

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

follow instructions.

can be killed or seriously injured if you don't

You instructions.

W10112488

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation. The parts supplied are in the washer basket.

Parts needed (not provided with washer):

■ Inlet hoses ■ Flat washers

Alternate Parts

Your installation may require additional parts. For information on ordering, please refer to the toll-free phone numbers on the front page of the Washer User Instructions.

If You Have: You Will Need to Buy:

To ord er:

■ Call the dealer from whom you purchased your washer.

■ Reference the toll-free number on the front page of the

Washer User Instructions.

■ Visit the website on the front page of the Washer User

Instructions.

NOTE: Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Record hose installation or replacement dates for future reference.

Parts supplied:

A. Beaded tie strap B. Front leveling feet with nuts (2) C. Drain hose form

Tools needed for installation:

■ Adjustable or open end

wrench ⁹⁄₁₆" (14 mm)

■ Level

■ Wood block

■ Ruler or measuring tape

■ Pliers that open to 1⁹⁄₁₆"

(3.95 cm)

■ Flashlight (optional)

Laundry tub or standpipe taller

Sump pump system (if not already available)

than 96" (2.4 m)

1" (2.5 cm) diameter standpipe

1¹⁄₄" (3.2 cm) diameter to 1" (2.5 cm) diameter standpipe adapter, Part Number 280130

Overhead sewer Standard 20 gal. (76 L) 39" (99 cm) tall

drain tub or utility sink, sump pump and connectors (available from local plumbing suppliers)

Floor drain Siphon break kit, Part Number 280129;

additional drain hose, Part Number 3357090

Water faucets beyond reach of fill hoses

Drain hose too

2 longer water fill hoses: 6 ft (1.8 m) Part Number 76314, 10 ft (3.0 m) Part Number 350008

Kit Part Number 280131

short

Lint clogged drain Drain protector, Part Number 367031

Location Requirements

19"

(48.3 cm)

(0 cm)

27"

(68.6 cm)

(2.5 cm)

¹⁄₂"

(64.8 cm)

4" (10.2 cm)

14" max. (35.6 cm)

(7.6 cm)

24 in. (155 cm )

48 in. (310 cm )

Selecting the proper location for your washer improves performance and minimizes noise and possible washer “walk.”

Your washer can be installed in a basement, laundry room, closet, or recessed area. See “Drain System.”

IMPORTANT: Do not install or store the washer where it will be exposed to the weather.

Proper installation is your responsibility.

You will need:

■ A water heater set to deliver 120°F (49°C) water to the washer.

■ A grounded electrical outlet located within 4 ft (1.2 m) of

where the power cord is attached to the back of the washer. See “Electrical Requirements.”

■ Hot and cold water faucets located within 3 ft (90 cm) of the

hot and cold water fill valves, and water pressure of 5-100 psi (34.5-690 kPa). Washers with triple dispensers require 20-100 psi (138-690 kPa) for best performance.

■ A level floor with a maximum slope of 1" (2.5 cm) under entire

washer. Installing the washer on carpeting is not recommended.

■ A sturdy floor to support the washer weight (washer, water

and load) of 315 lbs (143 kgs).

Do not store or operate your washer in temperatures at or below 32°F (0°C). Some water can remain in the washer and can cause damage in low temperatures. See “Washer Care” in the Washer User Instructions for winterizing information.

Recessed area or closet installation

Drain System

The washer can be installed using the standpipe drain system (floor or wall), the laundry tub drain system, or the floor drain system. Select the drain hose installation method you need. See “Tools and Parts.”

Standpipe drain system—wall or floor (views A & B)

The standpipe drain requires a minimum diameter standpipe of 2" (5 cm). The minimum carry-away capacity can be no less than 17 gal. (64 L) per minute. A 1¹⁄₄" (3.2 cm) diameter to 1" (2.5 cm) diameter standpipe adapter kit is available. See “Tools and Parts.”

The top of the standpipe must be at least 39" (99 cm) high and no higher than 96" (244 cm) from the bottom of the washer.

To avoid siphoning, no more than 8" (20.3 cm) of drain hose should be inside the standpipe. Secure drain hose with beaded tie strap.

39"

(99 cm)

The dimensions shown are for the recommended spacing allowed (A and B), except the closet door ventilation openings. The dimensions shown for the closet door ventilation openings (C) are the minimum required.

A. Front view B. Side view C. Closet door with vents

■ Additional spacing should be considered for ease of

installation and servicing.

■ Additional clearances may be required for wall, door and floor

moldings.

■ Additional spacing of 1" (2.5 cm) on all sides of the washer is

recommended to reduce noise transfer.

■ If a closet door is installed, the minimum air openings in the

top and bottom of the door are required (C). Louvered doors with air openings in the top and bottom are acceptable.

■ Companion appliance spacing should also be considered.

Laundry tub drain system (view C)

The laundry tub needs a minimum 20 gal. (76 L) capacity. The top of the laundry tub must be at least 39" (99 cm) above the floor and no higher than 96" (244 cm) from the bottom of the washer.

Floor drain system (view D)

The floor drain system requires a siphon break that may be purchased separately. See “Tools and Parts.”

The siphon break must be a minimum of 28" (71 cm) from the bottom of the washer. Additional hoses might be needed.

To avoid siphoning, no more than 8" (20.3 cm) of drain hose should be below the top of the wash tub. Secure drain hose with beaded tie strap.

39"

(99 cm)

28"

(71 cm)

Electrical Requirements

WARNING

Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

■ A 120 volt, 60 Hz., AC only, 15- or 20-amp, fused electrical

supply is required. A time-delay fuse or circuit breaker is recommended. It is recommended that a separate circuit serving only this appliance be provided.

■ This washer is equipped with a power supply cord having a

3 prong grounding plug.

■ To minimize possible shock hazard, the cord must be plugged

into a mating, 3 prong, grounding-type outlet, grounded in accordance with local codes and ordinances. If a mating outlet is not available, it is the personal responsibility and obligation of the customer to have the properly grounded outlet installed by a qualified electrician.

■ If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the ground path is adequate.

■ Do not ground to a gas pipe.

■ Check with a qualified electrician if you are not sure the

washer is properly grounded.

■ Do not have a fuse in the neutral or ground circuit.

GROUNDING INSTRUCTIONS

For a grounded, cord-connected washer:

This washer must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electrical shock by providing a path of least resistance for electric current. This washer is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

WARNING:

grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded.

Do not modify the plug provided with the appliance – if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

For a permanently connected washer:

This washer must be connected to a grounded metal, permanent wiring system, or an equipment grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the appliance.

Improper connection of the equipment-

INSTALLATION INSTRUCTIONS

Before You Start

WARNING

Excessive Weight Hazard Use two or more people to move and install washer. Failure to do so can result in back or other injury.

NOTE: To avoid floor damage, set the washer onto cardboard before moving across floor.

Remove Shipping Materials

Removing the shipping material is necessary for proper operation. If the shipping material is not removed, the washer will make excessive noise.

1. Move the washer to within approximately 3 ft (90 cm) of its

final location.

2. The washer must be in the upright position and not tilted

before removing the shipping material.

3. Locate the yellow shipping materials on the rear of the

machine, near the bottom. Follow the steps for your particular model, either the one with the straight power cord and cord restraint or the looped power cord version.

Straight power cord

1. Remove power plug and yellow strap from machine base to

release the rear leveling system.

4. To remove the power cord from the cord restraint, push the

power cord in, press TAB, and then pull the power cord out.

Looped power cord

2. Firmly grasp the power cord and pull to completely remove

the power cord, cord restraint, and pin from the rear panel.

3. Confirm that the power cord restraint (A), and pin (B) are

removed.

A. Power cord restraint B. Pin

1. Firmly grasp the yellow shipping strap and pull until both ends

are completely removed from washer.

2. Check that two (2) cotter pins were removed with the shipping

strap.

Connect Drain Hose

Proper connection of the drain hose protects your floors from damage due to water leakage. Read and follow these instructions.

The drain hose is connected to your washer and is stored inside the washer cabinet.

Remove drain hose from washer cabinet

Gently pull the corrugated drain hose out of the washer from the top of the hose. Continue to pull the hose until the end emerges. Do not force excess drain hose back into the rear of the washer.

Laundry tub drain or standpipe drain

Connecting the drain hose form to the corrugated drain hose

Connect the Inlet Hoses

The washer must be connected to the water faucets using new inlet hoses (not provided). Do not use old hoses.

Insert new flat washers into each end of the inlet hoses. Firmly seat the washers in the couplings.

A. Coupling B. Washer

Connect the inlet hoses to the water faucets

Make sure the washer basket is empty.

1. Attach hose to the hot water faucet. Screw on coupling by

hand until it is seated on the washer.

Attach hose to the cold water faucet. Screw on coupling by hand until it is seated on the washer.

3. Using pliers, tighten the couplings with an additional

two-thirds turn.

A. Drain hose reliefs

1. Feed end of drain hose into one end of form. Place end of

drain hose form into the drain hose relief.

2. Bend the hose over the top of the form and feed into the other

end of the form.

To keep drain water from going back into the washer:

■ Do not force excess drain hose into standpipe. Hose should

be secure but loose enough to provide a gap for air.

■ Do not lay excess hose on the bottom of the laundry tub.

Floor drain

Do not install the drain hose form on to the corrugated drain hose. You may need additional parts. See Floor drain under “Tool s a n d Parts.”

Tighten the couplings with an additional two-thirds turn.

NOTE: Do not overtighten or use tape or sealants on the valve. Damage to the valves can result.

Clear the water lines

■ Run water through both faucets and inlet hoses, into a laundry

tub, drainpipe or bucket, to get rid of particles in the water lines that might clog the inlet valve screens.

■ Check the temperature of the water to make sure that the hot

water hose is connected to the hot water faucet and that the cold water hose is connected to the cold water faucet.

Connect the inlet hoses to the washer

A B

A. Cold water inlet valve B. Hot water inlet valve

1. Attach the hot water hose to the bottom inlet valve.

2. Attaching the hot water coupling first makes it easier to

tighten connection with pliers.

3. Screw on coupling by hand until it is seated on the washer.

Secure the Drain Hose

1. Remove the shipping material from the power cord. Drape the

power cord over the console.

2. Remove any cardboard used to move washer.

Beaded tie strap

3. Wrap the drain hose to the laundry tub leg, drain standpipe or

inlet hoses, with the beaded tie strap. Push fastener into the nearest hole in the beaded tie strap. See view A or B.

CBA

4. Using pliers, tighten the couplings with an additional

two-thirds turn. NOTE: Do not overtighten or use tape or sealants on the

valve. Damage to the valves can result.

5. Attach the cold water hose to the top inlet valve.

6. Screw on coupling by hand until it is seated on the washer.

7. Using pliers, tighten the couplings with an additional

two-thirds turn. NOTE: Do not overtighten or use tape or sealants on the

valve. Damage to the valves can result.

Check for leaks

Turn on the water faucets and check for leaks. A small amount of water might enter the washer. You will drain this later.

NOTE: Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Record hose installation or replacement dates for future reference.

■ If you connect only one water hose, you must cap off the

remaining water inlet port.

■ Periodically inspect and replace hoses if bulges, kinks, cuts,

wear, or leaks are found.

If the washer faucets and the drain standpipe are recessed, put the formed end of the drain hose into the standpipe. Tightly wrap the tie strap around the water inlet hoses and the drain hose. See view C.

Level the Washer

Properly leveling your washer avoids excessive noise and vibration.

Install the Front Leveling Feet

1. Prop up the front of the washer about 4" (10.2 cm) with a

wood block or similar object. The block needs to support the weight of the washer.

(10.2 cm)

A. Threaded holes for feet

2. Screw the locknut onto each foot to within 1" (2.5 cm) of the

(2.5 cm)

foot base.

3. Screw the feet into the threaded holes at the front corner of

the washer until the nuts touch the washer. Twist the feet to install.

NOTE: Do not tighten the nuts until the washer is level.

4. If the washer is not level, move the washer out slightly, tip

back, prop up the front of the washer with the wood block and adjust the feet up or down as necessary by twisting the feet. Turn the feet clockwise to raise the washer or counterclockwise to lower the washer. Repeat steps 1 through 4 until washer is level.

5. After the washer is in the final location and level, use a ⁹⁄₁₆" or

14 mm open-end wrench to turn the nuts counterclockwise on the feet tightly against the washer cabinet.

IMPORTANT: If the nuts are not tight against the washer cabinet, the washer may vibrate.

4. Tilt the washer back and remove the wood block. Gently lower

the washer to the floor.

Steps in Final Location

1. Slide the washer to its final location.

2. Tilt the washer forward until the rear of the washer is at least

4" (10.2 cm) off the floor. You may hear the self-adjusting rear feet click into place. Lower the washer to the floor.

(10.2 cm)

A. Self-adjusting feet

3. Check the levelness of the washer by placing a level on the

top edges of the washer, first side to side, then front to back.

Complete Installation

1. Check the electrical requirements. Be sure that you have the

correct electrical supply and the recommended grounding method. See “Electrical Requirements.”

2. Check that all parts are now installed. If there is an extra part,

go back through the steps to see which step was skipped.

3. Check that you have all of your tools.

4. Check that the yellow shipping materials were completely

removed from the lower back of the washer.

5. Dispose of/recycle all packaging materials.

6. Check that the water faucets are on.

7. Check for leaks around faucets and inlet hoses.

WARNING

Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

8. Plug into a grounded 3 prong outlet.

9. Remove the protective film on the console and any tape

remaining on the washer.

10. Read “Washer Use” in the Washer User Instructions.

11. To test and to clean your washer, measure ¹⁄₂ of the normal

recommended amount of powdered or liquid detergent and pour it into the washer basket or detergent dispenser (on some models). Close the lid. Select any cycle, and then pull the cycle control knob out to start the washer. Allow it to complete one whole cycle.

+ 16 hidden pages