Whirlpool UXT4036AYB Installation Manual

30" (76.2 CM) AND 36" (91.4 CM) RANGE HOOD

IMPORTANT: READ AND SAVE THESE INSTRUCTIONS. FOR RESIDENTIAL USE ONLY. IMPORTANT : LIRE ET CONSERVER CES INSTRUCTIONS. POUR UTILISATION RÉSIDENTIELLE UNIQUEMENT.

Models/Modèles : UXT4030AY/UXT4036AY

LI3ZB/W10400319D

Installation Instructions and Use & Care Guide

For questions about features, operation/performance, parts, accessories or service, call: 1-800-253-1301

or visit our website at www.whirlpool.com

In Canada, call 1-800-807-6777 or visit our website at www.whirlpool.ca

HOTTE D’ASPIRATION DE

30" (76,2 CM) ET 36" (91,4 CM)

Instructions d’installation et Guide d’utilisation et d’entretien

Au Canada, pour assistance, installation ou service, composer

Table of Contents/Table des matières.............................................................................2

le 1-800-807-6777 ou visiter notre site Web à

www.whirlpool.ca

TABLE OF CONTENTS

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

State of California Proposition 65 Warnings: WARNING: This product contains one or more chemicals known to the State of California to cause cancer. WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

TABLE DES MATIÈRES

RANGE HOOD SAFETY .................................................................2

INSTALLATION REQUIREMENTS................................................4

Tools and Parts ............................................................................4

Location Requirements................................................................4

Venting Requirements..................................................................5

Electrical Requirements ...............................................................5

INSTALLATION INSTRUCTIONS..................................................6

Prepare Location..........................................................................6

Install Range Hood.......................................................................6

Make Electrical Connection .........................................................7

Complete Installation ...................................................................8

RANGE HOOD USE........................................................................8

Range Hood Controls ..................................................................8

RANGE HOOD CARE.....................................................................8

Cleaning........................................................................................8

WIRING DIAGRAM .........................................................................9

ASSISTANCE OR SERVICE.........................................................10

In the U.S.A. ...............................................................................10

In Canada ...................................................................................10

Accessories................................................................................10

WARRANTY ..................................................................................11

RANGE HOOD SAFETY

SÉCURITÉ DE LA HOTTE DE CUISINIÈRE................................12

EXIGENCES D'INSTALLATION...................................................14

Outils et pièces...........................................................................14

Exigences d'emplacement.........................................................14

Exigences concernant l’évacuation ...........................................15

Spécifications électriques ..........................................................15

INSTRUCTIONS D’INSTALLATION.............................................16

Préparation de l'emplacement...................................................16

Installation de la hotte ................................................................16

Raccordement électrique...........................................................17

Achever l’installation ..................................................................18

UTILISATION DE LA HOTTE .......................................................18

Commandes de la hotte de cuisinière .......................................18

ENTRETIEN DE LA HOTTE..........................................................18

Nettoyage ...................................................................................18

SCHÉMA DE CÂBLAGE...............................................................19

ASSISTANCE OU SERVICE.........................................................20

Au Canada..................................................................................20

Accessoires ................................................................................20

GARANTIE.....................................................................................21

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

■ Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the manufacturer.

■ Before servicing or cleaning the unit, switch power off at

service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

■ Installation work and electrical wiring must be done by

qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction.

■ Do not operate any fan with a damaged cord or plug.

Discard fan or return to an authorized service facility for examination and/or repair.

■ Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment manufacturer's guideline and safety standards such as those published by the National Fire Protection Association (NFPA), the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.

■ When cutting or drilling into wall or ceiling; do not damage

electrical wiring and other utilities.

■ Ducted fans must always be vented outdoors. CAUTION: For general ventilating use only. Do not use

to exhaust hazardous or explosive materials and vapors.

CAUTION: To reduce risk of fire and to properly exhaust

air, be sure to duct air outside - do not vent exhaust air into spaces within walls or ceilings, attics or into crawl spaces, or garages.

WARNING: TO REDUCE THE RISK OF FIRE, USE ONLY

METAL DUCTWORK.

WARNING: TO REDUCE THE RISK OF A RANGE TOP

GREASE FIRE:

■ Never leave surface units unattended at high settings.

Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings.

■ Always turn hood ON when cooking at high heat or when

flambeing food (i.e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambé).

■ Clean ventilating fans frequently. Grease should not be

allowed to accumulate on fan or filter.

■ Use proper pan size. Always use cookware appropriate for

the size of the surface element.

WARNING: TO REDUCE THE RISK OF INJURY TO

PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING:

■ SMOTHER FLAMES with a close fitting lid, cookie sheet, or

metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.

■ NEVER PICK UP A FLAMING PAN - you may be burned.

■ DO NOT USE WATER, including wet dishcloths or towels -

a violent steam explosion will result.

■ Use an extinguisher ONLY if:

– You know you have a class ABC extinguisher, and you

already know how to operate it.

– The fire is small and contained in the area where it

started. – The fire department is being called. – You can fight the fire with your back to an exit.

Based on "Kitchen Fire Safety Tips" published by NFPA.

■ WARNING: To reduce the risk of fire or electrical shock,

do not use this fan with any solid-state speed control device.

INSTALLATION REQUIREMENTS

†®TORX is a registered trademark of Saturn Fasteners, Inc.

(2.5 cm)

4¹⁵⁄₁₆"

(12.5 cm)

6⁹⁄₁₆" (16.7 cm) or 9⁹⁄₁₆" (24.4 cm)

29¹⁵⁄₁₆" (76.0 cm) or 35¹⁵⁄₁₆" (91.0 cm)

18⁵⁄₈"

(47.3 cm)

1¹⁄₂"

(3.8 cm)

(22.9 cm)

(5.1 cm)

⁷⁄₈"

(2.2 cm)

Tools and Parts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Tools needed

■ Drill

■ 1¹⁄₄" (3.0 cm) drill bit

■ ¹⁄₈" (3.0 mm) drill bit for pilot holes

■ Pencil

■ Wire stripper or utility knife

■ Tape measure or ruler

■ Caulking gun and weatherproof caulking compound

■ Flat-blade screwdriver

■ Phillips screwdriver

■ Saber or keyhole saw

Parts Supplied

■ T-10 Torx

■ 4 - 4.5 x 13 mm mounting screws

Parts Needed

■ 3 - UL listed wire connectors

■ 1 - 75W max, 120V incandescent light bulb

For cabinets with recessed bottoms:

■ Two 2" (5.1 cm) wide filler strips. Length and thickness

determined by recess dimensions.

■ Four flat head wood screws or machine screws with washers

and nuts (to attach filler strips).

®†

adapter

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

■ It is the installer’s responsibility to comply with installation

clearances specified on the model/serial rating plate. The model/serial rating plate is located inside the range hood on the left wall.

■ Range hood location should be away from strong draft areas,

such as windows, doors and strong heating vents.

■ Cabinet opening dimensions that are shown must be used.

Given dimensions provide minimum clearance. Consult the cooktop/range manufacturer installation instructions before making any cutouts.

■ This range hood is recommended for use with cooktops with

a maximum total rating of 40,000 BTUs or less.

■ Grounded electrical outlet is required. See “Electrical

Requirements” section.

■ All openings in ceiling and wall where range hood will be

installed must be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the Manufactured Home Construction Safety Standards, Title 24 CFR, Part 328 (formerly the Federal Standard for Mobile Home Construction and Safety, title 24, HUD, Part 280) or when such standard is not applicable, the standard for Manufactured Home Installation 1982 (Manufactured Home Sites, Communities and Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local codes.

Product Dimensions

Installation Clearances

A. 18" (45.7 cm) min. clearance - upper cabinet to countertop B. 24" (61.0 cm) minimum - bottom of range hood to cooking

surface

C. 30" (76.2 cm) min. cabinet opening width for 30" (76.2 cm)

models and 36" (91.4 cm) min. cabinet width for 36" (91.4 cm)

models D. 12" (30.5 cm) minimum cabinet depth E. 36" (91.4 cm) base cabinet height

Electrical Requirements

Observe all governing codes and ordinances. Ensure that the electrical installation is adequate and in

conformance with National Electrical Code, ANSI/NFPA 70 (latest edition), or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes and ordinances.

If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

■ A 120 volt, 60 Hz., AC only, 15-amp, fused electrical circuit is

required.

■ If the house has aluminum wiring, follow the procedure

below:

1. Connect a section of solid copper wire to the pigtail

leads.

2. Connect the aluminum wiring to the added section of

copper wire using special connectors and/or tools designed and UL listed for joining copper to aluminum.

Follow the electrical connector manufacturer's recommended procedure. Aluminum/copper connection must conform with local codes and industry accepted wiring practices.

■ Wire sizes and connections must conform with the rating of

the appliance as specified on the model/serial rating plate. The model/serial plate is located behind the filter on the rear wall of the range hood.

■ Wire sizes must conform to the requirements of the National

Electrical Code, ANSI/NFPA 70 (latest edition), or CSA Standards C22. 1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes and ordinances.

Venting Requirements

These range hoods are factory set for non-vented (recirculating) installations and come with a charcoal filter. See the “Accessories” section to order charcoal filter kit.

INSTALLATION INSTRUCTIONS

Cabinet bottom

Wall

3" (7.6 cm)

Wood filler strips (recessed cabinet bottoms only)

3" (7.6 cm)

Centerline

2" (5.1 cm) from wall, not cabinet frame

Centerline

⁷⁄₈" (2.2 cm)

¹⁄₄"

(6.4 mm)

Prepare Location

NOTE: Before making cutouts, make sure there is proper

clearance within the ceiling or wall.

1. Disconnect power.

2. Select a flat surface for assembling the range hood. Place

covering over that surface.

3. Lift the range hood and set it upside down onto covered

surface.

4. If cabinet has recessed bottom, add wood filler strips on each

side. Install screws to attach filler strips in locations shown.

Determine Wiring Hole Location

To wire through wall:

1. Mark a line distance “A” from the right of the centerline on the

underside of the wall. Mark the point on this line that is ⁷⁄₈" (2.2 cm) from the underside of the cabinet. Drill a 1¹⁄₄" (3.2 cm) diameter hole through the rear wall at this point.

A. 8³⁄₈" (21.3 cm)

Install Range Hood

1. Lift the range hood up under cabinet and determine final

location by centering beneath cabinet. Mark on the underside of cabinet the location of the 4 keyhole mounting slots on the range hood. Set range hood aside on a covered surface.

Cut only one 1¹⁄₄" (3.2 cm) diameter wiring access hole.

1. Determine and clearly mark a vertical centerline on the wall

and cabinet in the area the vent opening will be made.

A. Centerline

To wire through top:

1. Mark a line distance “A” from the right of the centerline on the

underside of the cabinet. Mark the point on this line that is 2" (5.1 cm) from back wall. Drill a 1¼" (3.2 cm) diameter hole through the cabinet at this point.

A. Keyhole slot

2. Use ¹⁄₈" (3 mm) drill bit and drill 4 pilot holes as shown.

A. Drill pilot hole

3. Install the 4 - 4.5 mm x 13 mm mounting screws in pilot

holes. Leave about ¹⁄₄" (6.4 mm) space between screw heads and cabinet to slide range hood into place.

Non-vent (recirculating) installations - Do not remove any knockouts.

A. 8³⁄₈" (21.3 cm)

Power Supply Cable Installation

WARNING

Electrical Shock Hazard Disconnect power before servicing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock.

WARNING

Fire Hazard Electrically ground the blower. Use copper wire. Connect ground wire to green ground screw in

terminal box. Failure to do so can result in death, fire, or

electrical shock.

1. For direct wire installations, run the home power supply cable

according to the National Electric Code or CSA standards and local codes and ordinances. There must be enough wiring from the fused disconnect (or circuit breaker) box to make the connection in the hood electrical terminal box.

For optional power supply cord kit installations, follow the instructions in the “Make Electrical Connections” section.

NOTES:

■ Do not reconnect power until the installation is complete.

■ Use only with range hood cord connection kits that have

been investigated and found acceptable for use with this model range hood.

2. Remove the screw from the terminal box cover. Remove

terminal box cover and set aside.

A. Terminal box cover B. Screw

Make Electrical Connection

1. Disconnect power.

3. Remove the power supply knockout from the top or rear of

the vent hood (depending on the incoming location of your home power supply cable) and install a UL listed or CSA approved ¹⁄₂" strain relief.

A. Power supply knockout

4. Using 2 or more people, lift the hood into final position. Feed

enough electrical wire through the ½" UL listed or CSA approved strain relief to make connections in the terminal box. Tighten the strain relief screws.

5. Position the range hood so that the large end of the keyhole

slots are over the mounting screws. Then push the hood toward the wall so that the screws are in the neck of the slots. Tighten the mounting screws, making sure the screws are in the narrow neck of slots.

A. White wires B. Black wires C. UL listed wire connector D. Green (or bare) ground wire

2. Use UL listed wire connectors and connect white wires (A)

together.

3. Use UL listed wire connectors and connect black wires (B)

together.

E. Home power supply cable or

power cord accessory kit

F. UL listed or CSA approved

½" strain relief

G. Green ground screw

4. Connect green (or bare) ground wire from power supply to

green ground screw in terminal box and securely tighten.

5. Install terminal box cover.

6. Reconnect power.

Complete Installation

Off

On Low

Off

High

1. Install the 75W (max.) Incandescent light bulb. See

“Replacing the Incandescent Light Bulb” in the “Range Hood Care” section.

2. Replace grease filter if removed. See the “Range Hood Care”

section.

RANGE HOOD USE

The range hood is designed to remove smoke, cooking vapors and odors from the cooktop area. For best results, start the hood before cooking and allow it to operate several minutes after the cooking is complete to clear all smoke and odors from the kitchen.

The hood controls are located on the top of the range hood.

A. Incandescent light housing and cover B. Charcoal filter retainer C. Grease filter

3. Check the operation of the range hood fan and light. See

“Range Hood Use” section. If range hood does not operate, check to see whether a

circuit breaker has tripped or a household fuse has blown. Disconnect power and check wiring connections.

NOTE: To get the most efficient use from your new range hood, read the “Range Hood Use” section.

Range Hood Controls

A. On/Off light switch B. Fan speed switch

Operating the light

Push the light switch to the right to turn the light Off. Push the light switch to the left to the turn the light On.

Operating the fan

Push the fan switch to the left for Low speed. Push the fan switch to the right for High speed. Push the fan switch to the middle for Off.

IMPORTANT: Clean the hood and grease filters frequently according to the following instructions. Replace grease filter before operating hood.

Exterior Surfaces:

IMPORTANT: Do not use soap-filled scouring pads, abrasive

cleaners, Cooktop Polishing Creme, steel wool, gritty washcloths or paper towels.

To avoid damage to the stainless steel, do not use cleaners that contain chlorine.

Cleaning Method:

■ Rub in direction of grain to avoid scratching or damaging the

surface.

■ For stainless steel models, Stainless Steel Cleaner and Polish

Part Number 31462A (not included): See “Assistance or Service” section to order.

■ Liquid detergent or all-purpose cleaner:

Rinse with clean water and dry with soft, lint-free cloth.

■ Glass cleaner to remove fingerprints.

RANGE HOOD CARE

Cleaning

Charcoal Filter

The charcoal filter is not washable. It should last up to 6 months with normal use.

Replace the old charcoal filter with a new charcoal filter. For information on ordering, see the “Accessories” section.

To replace filter:

1. Remove screw from the filter retainer.

2. Turn the filter retainer to release filter.

A. Filter retainer

3. Reinstall the filter by placing the back edge in the channel at

rear of hood. Push filter into place, turn the filter retainer to secure filter to range hood.

4. Replace screw in the filter retainer.

+ 16 hidden pages