Whirlpool UXT3036AYB0, UXT4036AS0, UXT4036AB0, UXT4236AYW0, UXT4030AT0 Installation Instructions And Use & Care Manual

30" (76.2 CM) AND 36" (91.4 CM) RANGE HOODS

For questions about features, operation/performance, parts, accessories or service, call: 1-800-253-1301

or visit our website at www, whirlpool,com

In Canada, call 1-800-807-6777 or visit our website at www, whirlpool,ca

HOTTED'ASPIRATIONDE

30"(76,2 CM) ET36"(91,4 CM)

Au Canada, pour assistance, installation ou service, composer

le 1-800-807-6777 ou visiter notre site Web

www,whirlpool,ca

Table of Contents/Table des matieres ............................................................................. 2

ModelsiMod@Jes:
UXT2030AY/UXT2036AY
UXT3030AY/UXT3036AY
UXT4030AY/UXT4036AU

_odeJs/_od@Jes:
UXT4230AY/UXT4236AY

_odeJs/_od@Jes:
UXT5230AY/UXT5236AY

I_PORTANT: READ AND SAVE THESE INSTRUCTIONS.

FOR RESIDENTIAL USE ONLY.

I_PORTANT : URE ET CONSERVER CES iNSTRUCTIONS.

POUR UTIUSATION RES_DENT_ELLE UNJQUE_ENT.

LI3ZMA/W10349965C

TABLEOF CONTENTS TABLEDESMATIERES

RANGE HOOD SAFETY ................................................................. 2

INSTALLATION REQUIREMENTS ................................................ 4

Tools and Parts ............................................................................ 4

Location Requirements ................................................................ 5

Venting Requirements .................................................................. 5

Electrical Requirements ............................................................... 7

INSTALLATION INSTRUCTIONS .................................................. 8

Prepare Location.......................................................................... 8

Install Range Hood ..................................................................... 10

Make Electrical Connection ....................................................... 12

Complete Installation ................................................................. 12

RANGE HOOD USE ...................................................................... 12

Range Hood Controls ................................................................ 13

RANGE HOOD CARE ................................................................... 13

Cleaning ...................................................................................... 13

WIRING DIAGRAM ....................................................................... 15

ASSISTANCE OR SERVICE ......................................................... 17

In the U.S.A................................................................................ 17

In Canada ................................................................................... 17

Accessories ................................................................................ 17

WAR RANTY .................................................................................. 18

SECURITE DE LA HOTTE DE CUlSINIERE ............................... 19

EXIGENCES D'INSTALLATION ................................................... 21

Outils et pieces ........................................................................... 21

Exigences d'emplacement ......................................................... 22

Exigences concernant I'evacuation ........................................... 23

Specifications electriques .......................................................... 24

INSTRUCTIONS D'INSTALLATION ............................................. 25

Preparation de I'emplacement ................................................... 25

Installation de la hotte ................................................................ 27

Raccordement electrique ........................................................... 29

Achever I'installation .................................................................. 29

UTILISATION DE LA Ho'n'E ....................................................... 29

Commandes de lahotte de cuisiniere ....................................... 30

ENTRETIEN DE LA HOTTE .......................................................... 31

Nettoyage ................................................................................... 31

SCHEMA DE CABLAGE ............................................................... 33

ASSISTANCE OU SERVICE ......................................................... 35

Au Canada .................................................................................. 35

Accessoires ................................................................................ 35

GARANTIE ..................................................................................... 36

RANGE HOOD SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow
instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.

2

IMPORTANT SAFETY INSTRUC ONS

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, OR iNJURY TO PERSONS, OBSERVE THE
FOLLOWING:

[] Use this unit only in the manner intended by the

manufacturer, tfyou have questions, contact the
manufacturer.

[] Before servicing or cUeaningthe unit, switch power off at

service panel and lock the service disconnecting means to
prevent power from being switched on accidentally. When
the service disconnecting means cannot be locked,
secureUy fasten a prominent warning device, such as a tag,
to the service panel

[] Installation work and eUectricaUwiring must be done by

qualified person(s) in accordance with all appHcabUecodes
and standards, including fire-rated construction.

[] Do not operate any fan with a damaged cord or plug.

Discard fan or return to an authorized service facility for

examination and!or repair.

[] Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of fuel
burning equipment to prevent backdrafting. Follow the

heating equipment manufacturer's guideline and safety

standards such as those published by the National Fire

Protection Association (NFPA), the American Society for
Heating, Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

[] When cutting or drilling into wall or ceiling; do not damage

electrical wiring and other utilities.

[] Ducted fans must always be vented outdoors.

CAUTION: For general ventilating use only. Do not use
to exhaust hazardous or explosive materials and vapors.

CAUTION: To reduce risk of fire and to properly exhaust
air, be sure to duct air outside - do not vent exhaust air into
spaces within walls or ceilings, attics or into crawl spaces,

or garages.

WARNING: TO REDUCE THE RISK OF FIRE, USE ONLY
METAL DUCTWORK.

WARNING: TO REDUCE THE RISK OF A RANGE TOP

GREASE FIRE:

[] Never leave surface units unattended at high settings.

Boilovers cause smoking and greasy spillovers that may
ignite. Heat oils slowly on low or medium settings.

[] Always turn hood ON when cooking at high heat or when

fiambeing food (i.e. Crepes Suzette, Cherries Jubilee,

Peppercorn Beef Flamb6).

[] Clean ventilating fans frequently. Grease should not be

allowed to accumulate on fan or filter.

[] Use proper pan size. Always use cookware appropriate for

the size of the surface element.

WARNING: TO REDUCE THE RISK OF INJURY TO

PERSONS IN THE EVENT OF A RANGE TOP GREASE
FIRE, OBSERVE THE FOLLOWING: "

[] SMOTHER FLAMES with a close fitting lid, cookie sheet, or

metal tray, then turn off the burner. BE CAREFUL TO
PREVENT BURNS. Ifthe flames do not go out
immediately, EVACUATE AND CALL THE FIRE

DEPARTMENT.

[] NEVER PICK UP A FLAMING PAN - you may be burned.
[] DO NOT USE WATER, including wet dishcloths or towels -

a violent steam explosion will result.

[] Use an extinguisher ONLY if:

- You know you have a class ABC extinguisher, and you
already know how to operate it.

- The fire is small and contained in the area where it
started.

- The fire department is being called.

- You can fight the fire with your back to an exit.

aBased on "Kitchen Fire Safety Tips" published by NFPA.
[] WARNING: To reduce the risk of fire or electrical shock,

do not use this fan with any solid-state speed control
device.

READ AND SAVE THESE INSTRUCTIONS

INSTALLATIONREQUIREMENTS

Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed

here.

Tools needed (all models)

• Drill

• 1V4" (3.0 cm) drill bit

• 1/8"(3.0 mm) drill bit for pilot holes

• Pencil

• Wire stripper or utility knife

• Tape measure or ruler

• Caulking gun and weatherproof caulking compound

• Flat-blade screwdriver

• Phillips screwdriver

• Saber or keyhole saw

• Metal snips

• Compass or 8" (20.3 cm) circle template

Parts Supplied (all models)

• T-10 Torx®tadapter

• T-20 Torx®tadapter

• 4- 4.5 x 13 mm mounting screws
Parts Needed (all models)

• 3 - UL listed wire connectors

• Vent clamps/duct tape as required
For cabinets with recessed bottoms:

• Two 2" (5.1 cm) wide filler strips. Length and thickness
determined by recess dimensions.

• Four flat head wood screws or machine screws with washers
and nuts (to attach filler strips).

Parts needed

• 31/4"x 10" (8.3 x 25.4 cm) rectangular metal vent system

• Wall or roof cap with damper to match vent system

• 1 - 75W max, 120V incandescent light bulb

Models UXT4030AY/UXT4036AY
(recirculation installation only)

Parts needed

• 1 - 75W max, 120V incandescent light bulb

Models UXT4230AY/UXT4236AY
(vented or non-vented [recirculation] installation)

Parts supplied

Remove parts from package. Check that all parts are included.

• 2 - 3.5 x 9.5 mm screws

• 31/4"x 10" (8.3 x 25.4 cm) rectangular vent connector

Parts needed

• 1 - 75W max, 120V incandescent light bulb

• Wall or roof cap with damper to match vent system
For 7" (17.8 cm) round vented installations:

• 7" (17.8 cm) round metal vent sytem

• 7" (17.8 cm) round damper. For information on ordering, see
the "Accessories" section.

• 7" (17.8 cm) round vent mounting plate. For information on
ordering, see the "Accessories" section.

For 31/4'' x 10" (8.3 x 25.4 cm) rectangular vented installations:

• 31/4"x 10" (8.3 x 25.4 cm) rectangular metal vent system

For non-vented (recirculation) installations:

• Charcoal filter kit. For information on ordering, see the
"Accessories" section.

Models UXT2030AY/UXT2036AY (vented installation)

Parts supplied

Remove parts from package. Check that all parts are included.

• 2 - 3.5 x 9.5 mm screws

• 7" (17.8 cm) round vent mounting plate

Parts needed

• 7" (17.8 cm) round metal vent system

• Wall or roof cap with damper to match vent system

• 1 - 75W max, 120V incandescent light bulb

Models UXT3030AY/UXT3036AY (vented installation)

Parts supplied

Remove parts from package. Check that all parts are included.

• 2 - 3.5 x 9.5 mm screws

• 31/4"x 10" (8.3 x 25.4 cm) rectangular vent connector

Models UXT5230AY/UXT5236AY
(vented or non-vented [recirculation] installation)

Parts supplied

Remove parts from package. Check that all parts are included.

• 2 - 3.5 x 9.5 mm screws

• 31/4"x 10" (8.3 x 25.4 cm) rectangular damper/vent connector

Parts needed

• Wall or roof cap with damper to match vent system

For 7" (17.8 cm) round vented installations:

• 7" (17.8 cm) round metal vent sytem

• 7" (17.8 cm) round damper. For information on ordering, see
the "Accessories" section.

• 7" (17.8 cm) round vent mounting plate. For information on
ordering, see the "Accessories" section.

For 31/4'' x 10" (8.3 x 25.4 cm) rectangular vented installations:

• 31/4"x 10" (8.3 x 25.4 cm) rectangular metal vent system

For non-vented (recirculation) installations:

• Charcoal filter kit. For information on ordering, see the
"Accessories" section.

1-®TORX is a registered trademark of Saturn Fasteners, Inc.

IMPORTANT: Observe all governing codes and ordinances.

• It is the installer's responsibility to comply with installation
clearances specified on the model/serial rating plate. The
model/serial rating plate is located inside the range hood on

the left wall.

• Range hood location should be away from strong draft areas,
such as windows, doors and strong heating vents.

• Cabinet opening dimensions that are shown must be used.
Given dimensions provide minimum clearance. Consult the
cooktop/range manufacturer installation instructions before
making any cutouts.

• Grounded electrical outlet is required. See "Electrical
Requirements" section.

• All openings in ceiling and wall where range hood will be
installed must be sealed.

These range hoods are factory set for vented installations.
Models that are capable of being installed as non-vented
(recirculating) require charcoal filters. See the "Accessories"

section to order charcoal filter kit.

For Mobile Home Installations

The installation of this range hood must conform to the
Manufactured Home Construction Safety Standards, Title 24
CFR, Part 328 (formerly the Federal Standard for Mobile Home
Construction and Safety, title 24, HUD, Part 280) or when such
standard is not applicable, the standard for Manufactured Home
Installation 1982 (Manufactured Home Sites, Communities and
Setups) ANSI A225.1/NFPA 501A*, or latest edition, or with local

codes.

Product Dimensions

Installation Clearances

A

B

C

E

A. 18" (45.7 cm) min. clearance - upper cabinet to countertop
B. 18" (45. 7 cm) to 24" (61.0 cm) suggested max. - bottom of range

hood to cooking surface

C. 30" (76.2 cm) min. cabinet opening width for 30" (76.2 cm)

models and 36" (91.4 cm) min. cabinet width for 36" (91.4 cm)
models.

D. 13" (33.0 cm) cabinet depth

E. 36" (91.4 cm) base cabinet height

Vent system must terminate to the outdoors, except for non-
vented (recirculating) installations.

Do not terminate the vent system in an attic or other enclosed
area.

Do not use a 4" (10.2 cm) laundry-type wall cap.
Use a 7" (17.8 cm) round metal vent or a 3V4"x 10" (8.3 x

25.4 cm) rectangular metal vent, depending on your model.
Rigid metal vent is recommended. Plastic or metal foil vent is

not recommended.
The length of vent system and number of elbows should be

kept to a minimum to provide efficient performance.

For the most efficient and quiet operation:

• Use no more than three 90° elbows.

• Make sure there is a minimum of 24" (61 cm) of straight vent
between the elbows if more than 1 elbow is used.

• Do not install 2 elbows together.

• Use clamps or duct tape to seal all joints in the vent system.

• The vent system must have a damper. If roof or wall cap has a
damper, do not use damper supplied with the range hood.

• Use caulking to seal exterior wall or roof opening around the
cap.

Cold Weather Installations

An additional back draft damper should be installed to minimize
backward cold air flow and a thermal break should be installed to

minimize conduction of outside temperatures as part of the vent
system. The damper should be on the cold air side of the thermal

break.
The break should be as close as possible to where the vent

system enters the heated portion of the house.

Makeup Air

Local building codes may require the use of makeup air systems
when using ventilation systems greater than specified CFM of air
movement. The specified CFM varies from locale to locale.
Consult your HVAC professional for specific requirements in your

area.

Venting Methods

Vent system can terminate either through the roof or wall. Use
31/4'' x 10" (8.3 x 25.4 cm) rectangular with a maximum vent
length of 35 ft (10.7 m) or 7" (17.8 cm) or larger round vent with a
maximum length of 50 ft (15.2 m) for vent system.

NOTE: Flexible vent is not recommended. Flexible vent creates
both back pressure and air turbulence that greatly reduce

performance.

Roof Venting Wall Venting

A

C

A. 7" (17.8 cm) round vent

through roof

(purchased separately).
31/4''x 10" (8.3 x 25.4 cm)
rectangular vent through the
roof for series UXT30, UXT42
and UXT52 (purchased
separately).

B. Roof cap

(purchased separately)

C. 18" (45.Tcm) min. to

24" (61.0 cm) max. above the

cooking surface.

A. 7" (17.8 cm) round ventout the

top and through the wall
(purchased separately).
31/4''x 10" (8.3 x 25.4 cm)
rectangular vent through the
wall or out the top for series

UXT30, UXT42 and UXT52
(purchased separately).

B. Wall cap

(purchased separately)

C. 18" (45. 7 cm) min. to

24" (61.0 cm) max. above the
cooking surface.

Calculating Vent System Length

To calculate the length of the system you need, add the

equivalent feet (meters) for each vent piece used in the system.

7" (17.8 cm) Round Vent System

Vent Piece Round

45° elbow 2.5 ft

(0.8m)

90° elbow 5.0 ft

(1.5m)

7" (17.8 cm) wall cap 0.0 ft

(o.om)

31/4"x 10" (8.3 cm x 25.4 cm) 4.5 ft
to 7" (17.8 cm) (1.4 m)

31/4"x 10" (8.3 cm x 25.4 cm) 5.0 ft
to 7" (17.8 cm) 90° elbow (1.5 m)

Example vent system

7" (17.8 cm) round

Wall cap

6 ft (1.8 rn) ]_

90 ° e_bow

2 ft (0.6 m)

Maximum Recommended Length = 50 ft (15.2 m)

1 - 90 ° elbow
1 - wall cap

8 ft (2.4 m) straight
Length of 7" (17.8 cm) system

= 5.0 ft (1.5 m)
= 0.0 ft (0.0 m)
= 8.0 ft (2.4 m)
= 13.0 ft (3.9 m)

6

31/4"x 10" (8.3 cm x 25.4 cm) Vent System

Vent Piece

31/4"x 10" (8.3 cm x 25.4 cm) 5.0 ft
90° elbow (1.5 m)

31/4"x 10" (8.3 cm x 25.4 cm) 12.0 ft
flat elbow (3.7 m)

31/4"x 10" (8.3 cm x 25.4 cm) 0.0 ft
wall cap (0.0 m)

Example vent system

31/4,, x 10,,

(8.3 x 25.4 cm)

e_bow

6 ft (1.8 rn) _ Wall cap

Maximum Recommended Length = 35 ft (10.7 m)

1 - 90° elbow
8 ft (2.4 m) straight

1 - wall cap
Length of 31/4'' x 10" (8.3 cm x 25.4 cm)

system

= 5.0 ft (1.5 m)
= 8.0 ft (2.4 m)
= 0.0 ft (0.0 m)
= 13.0 ft (3.9 m)

E cQ sfs

Observe all governing codes and ordinances.
Ensure that the electrical installation is adequate and in

conformance with National Electrical Code, ANSI/NFPA 70 (latest
edition), or CSA Standards C22.1-94, Canadian Electrical Code,
Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes

and ordinances.
If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the
ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park

Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

• A 120 volt, 60 Hz., AC only, 15-amp, fused electrical circuit is
required.

• If the house has aluminum wiring, follow the procedure
below:

1. Connect a section of solid copper wire to the pigtail

leads.

2. Connect the aluminum wiring to the added section of

copper wire using special connectors and/or tools

designed and UL listed for joining copper to aluminum.
Follow the electrical connector manufacturer's recommended
procedure. Aluminum/copper connection must conform with

local codes and industry accepted wiring practices.
Wire sizes and connections must conform with the rating of

the appliance as specified on the model/serial rating plate.
The model/serial plate is located behind the filter on the rear
wall of the range hood.

Wire sizes must conform to the requirements of the National
Electrical Code, ANSI/NFPA 70 (latest edition), or CSA
Standards C22.1-94, Canadian Electrical Code, Part 1 and
C22.2 No. 0-M91 (latest edition) and all local codes and

ordinances.

INSTALLATIONINSTRUCTIONS

NOTE: It is recommended that the vent system be installed
before hood is installed.

Before making cutouts, make sure there is proper clearance
within the ceiling or wall for exhaust vent.

1. Disconnect power.

2. Depending on your model, determine which venting method
to use: roof, wall or non-vented (recirculating).

3. Select a flat surface for assembling the range hood. Place
covering over that surface.

4. Lift the range hood and set it upside down onto covered
surface.

5. If cabinet has recessed bottom, add wood filler strips on each
side. Install screws to attach filler strips in locations shown.

Wood filler strips
(recessed cabinet
bottoms only)

To wire through top:

1. Mark a line distance "A" from the right of the centerline on the
underside of the cabinet. Mark the point on this line that is
7/8"(2.2 cm) from back wall. Drill a 1W' (3.2 cm) diameter hole
through the cabinet at this point.

A

%" (2.2 cm}
from wall,

not cabinet
frame

A. 8%" (21.3 cm) for30" (76.2 cm) models

11%" (28.9 cm) for 36" (91.4 cm) models

3" (7.6 ore) Wait

Determine Wiring Hole Location

Cut only one 1V4"(3.2 cm) diameter wiring access hole. See
Step 2 for wiring hole location instructions.

1. Determine and clearly mark a vertical centerline on the wall
and cabinet in the area the vent opening will be made.

A. Centerline

To wire through wall:

1. Mark a line distance "A" from the right of the centerline on the
underside of the wall. Mark the point on this line that
is 7/8"(2.2 cm) from the underside of the cabinet. Drill a
1V4" (3.2 cm) diameter hole through the rear wall at this point.

?

Centerline

A. 8%" (21.3 cm) for30" (76.2 cm) models

11%" (28.9 cm) for 36" (91.4 cm) models

Style I - Cut Openings for 3¼" x 10" (8.3 cm x 25.4 cm)
Rectangular Vent System

Roof Venting

To make a 41/4'' x 101/2'' (10.8 cm x 26.7 cm) rectangular cutout

on the underside of cabinet top and bottom:

1. Mark lines 1/2"(1.3 cm) and 43/4" (12.1 cm) from the back wall
on the centerline of the underside of cabinet.

2. Mark lines 51¼'' (13.3 cm) to the right and left of the centerline
on the underside of cabinet.

3. Use saber or keyhole saw to cut a rectangular opening for
vent.

8

4. Repeat steps 1-3 for the underside of the top of the cabinet.

i i' I'

c ti

Cabinet

cm)

*From watt, not cabinet frame

Wall Venting
To make a 31/2'' x 101/2'' (8.9 cm x 26.7 cm) rectangle in the

wall:

1. Make 2 lines by measuring 3/8"(0.9 cm) and 37/8"(9.8 cm)
down from underside of cabinet and mark on the centerline
on the back wall.

2. Mark lines 51¼"(13.3 cm) to the right and left of the centerline
on the wall.

3. Use saber or keyhole saw to cut a rectangular opening in the
wall for the vent.

51/4" 5V4"

(13.3 cm) (13.3 cm)

Style 2 - Cut Openings for 31/4'' x 10" (8.3 x 25.4 cm)
Rectangular Vent to Round Vent Transition

Roof Venting
To make a 41/4''x 101/2'' (10.8 cm x 26.7 cm) rectangular cutout

on the underside of cabinet bottom:

1. Mark lines 1/2"(1.3 cm) and 43/4"(12.1 cm) from the back wall
on the centerline of the underside of cabinet.

2. Mark lines 51¼'' (13.3 cm) to the right and left of the centerline
on the underside of cabinet.

3. Use saber or keyhole saw to cut a rectangular opening for
vent.

12.1 cm) /

5V4" \

(13.3 cm)

*From watt, not cabinet frame

To make a circular vent opening on the underside of the
cabinet top:

1. Mark a centerline on the underside of the top of cabinet.

2. Mark a line 5" (12.7 cm) from the back wall on the underside
of the top of cabinet.

3. Use a compass or a circle template to draw a circle with a
diameter that is 1¼,,(0.64 cm) larger than the vent.

4. Use saber or keyhole saw to cut the circular vent opening.

Circutar vent opening

//'

/i

*From wall, not

cabinet frame

J

Cabinet

cutouts

Style 3 - Cut Openings for 7" (17.8 cm) Round Vent

To make a circular vent openings on the underside of the

cabinet top and bottom:

1. Mark a centerline on the underside of the top of cabinet.

2. Mark a line 5" (12.7 cm) from the back wall on the underside
of the top and bottom of cabinet.

3. Use a compass or a circle template to draw a circle with a
diameter that is 1¼,,(0.64 cm) larger than the vent.

4. Use saber or keyhole saw to cut the circular vent opening.

17V4" (18.4 cm) diam.

cabinet cutouts

*From wail not

cabinet frame

Install Vent System

1. Install vent through the vent opening in upper cabinet or wall.
Complete venting system according to the selected venting

method. See "Venting Requirements" section.

2. Use caulking to seal exterior wall or roof opening around the
cap.

1.

2.

3.

,, a¸ ,, _ ,

_,,_S_3_{?_,_,_ _{_s_ _

Lift the range hood up under cabinet and determine final &
location by centering beneath cabinet. Mark on the underside
of cabinet the location of the 4 keyhole mounting slots on the
range hood. Set range hood aside on a covered surface.

A

\

A. Keyhole slot

Use V8"(3 mm) drill bit and drill 4 pilot holes as shown.

A

A.Drill pilot hole

Install the 4 - 4.5 mm x 13 mm mounting screws in pilot
holes. Leave about V4" (6.4 cm) space between screw heads
and cabinet to slide range hood into place.

6.

Remove metal grease filters. See the "Range Hood Care"
section.

NOTE: Depending on your model, you will have either a
7" (17.8 cm) round vent mounting plate or 3-1/4" x 10"
(8.3 x 25.4 cm) rectangular vent connector on the inside your
range hood. Some models are recirculation (non-vented only)
and will not have a vent damper.

Remove the 7" (17.8 cm) round vent mounting plate and the
3-1/4" x 10" (8.3 x 25.4 cm) rectangular vent connector
attached with screws or taped on the inside your range hood.

1i4uu

(6.4 ram)

4. Remove damper knockouts depending on your model.

C

A. Round vent knockout
B. Top rectangular vent knockout

C. Rear rectangular vent knockout

Round vent system installations - Remove top rectangular
and round vent knockouts.

Rectangular vent system installations - For roof
installations, remove the top rectangular vent knockout. For
wall installations, remove the rear rectangular vent knockout.

Non-vent (recirculating) installations - Do not remove any
knockouts.

7,

B

A. 7" (17.8 cm) round vent mounting plate

B. Screws

C. 3 _" X 10" (8.3 X24.4 cm) rectangular vent connector

Install 7" (17.8 cm) round vent mounting plate or 3-1/4" x 10"
(8.3 x 25.4 cm) vent connector, depending on your vent
system installation. Attach to range hood 6.5 x 9.5mm screws
provided and remove tape from damper flap.

NOTE: On some models, the 7" (17.8 cm) round vent
mounting plate is not supplied. An optional 7" (17.8 cm)
round damper is also available as an accessory. For
information on ordering, see the "Accessories" section.

!

_A

B

D

E

A. 7" (17.8 cm) Round damper (see "Accessories" section)
B. Sheet metal screws

C. 7" (17.8 cm) round vent mounting plate

D. Round vent knockout

E. Rectangular vent knockout

10

NOTE: The 7" (17.8 cm) round vent mounting plate and
31/4'' x 10" (8.3 x 25.4 cm) rectangular vent connector can
be installed up to 1" (2.5 cm) on either side of the hood

center to accommodate off center ductwork.

C

I

B

A. Vertical connector

B. 6.5 x 9.5 mm screws
C. Vent knockouts
D. Horizontal connector

If a vent damper is installed with a wall cap with damper,
check to make sure they do not interfere with each other.
Remove the vent connector damper flap if they interfere.

Non-vented (recirculating) installations - No vent
attachments. The UXT42 and UXT52 series models

require the removal of the recirculation cover plate.
Remove the two screws from the recirculation cover plate

and remove.

A

Power Supply Cable Installation

1. For direct wire installations, run the home power supply cable
according to the National Electric Code or CSA standards
and local codes and ordinances. There must be enough
wiring from the fused disconnect (or circuit breaker) box to

make the connection in the hood electrical terminal box.
For optional power supply cord kit installations, follow the

instructions included with the power supply cord kit.
NOTE: Do not reconnect power until the installation is

complete.

2. Remove the screw from the terminal box cover. Remove
terminal box cover and set aside.

A. Terminal box cover

B. Screw

3=

Remove the power supply knockout from the top or rear of
the vent hood (depending on the incoming location of your
home power supply cable) and install a UL listed or CSA
approved 1/2"strain relief.

A

A. Recirculation cover plate
B. Screws

A. Power supply knockout

4. Using 2 or more people, lift the hood into final position. Feed
enough electrical wire through the 1/2"UL listed or CSA

approved strain relief to make connections in the terminal
box. Tighten the strain relief screws.

5. Position the range hood so that the large end of the keyhole
slots are over the mounting screws. Then push the hood

toward the wall so that the screws are in the neck of the slots.
Tighten the mounting screws, making sure the screws are in

the narrow neck of slots.

6. Connect ventwork to hood. Seal joints with vent clamps or
duct tape to make secure and airtight.

7. Check that back draft dampers work properly.

11