Whirlpool UXT4030AA, UXT3030AA, UXT3036AA, UXT2036AA, UXT2030AA User Manual

UXT3030AA SERIES	UXT4030AA	SERIES
UXT3036AA	UXT4036AA
product visit	ECONOMY RANGE HOOD UXT2036AA SERIES
To register this

www.broan.com INSTALLATION INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

! INTENDED FOR DOMESTIC COOKING ONLY. !

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1.Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty.

2.Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

3.Installation work and electrical wiring must be done by a qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction codes and standards.

4.Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment manufacturer's guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.

5.When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

6.Ducted fans must always be vented to the outdoors.

7.Do not use this range hood with an additional speed control device.

8.To reduce the risk of fire, use only metal ductwork.

9.Use with approved cord-connection kit only.

10.This unit must be grounded.

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

1.Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings.

2.Always turn hood ON when cooking at high heat or when cooking flaming foods.

3.Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter.

4.Use proper pan size. Always use cookware appropriate for the size of the surface element.

WARNING

TO REDUCE THE RISK OFINURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING:*

1.SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.

2.NEVER PICK UP A FLAMING PAN - You may be burned.

3.DO NOT USE WATER, including wet dishcloths or towels - a violent stream explosion will result.

4.Use an extinguisher ONLY if:

A.You know you a Class ABC extinguisher and you already know how to operate it.

B.The fire is small and contained in the area where it started.

C.The fire department is being called.

D.You can fight the fire with your back to an exit.

*Based on “Kitchen Firesafety Tips” published by NFPA.

CAUTION !

1.For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors.

2.To avoid motor bearing damage and noisy/and or unbalanced impellers, keep drywall spray, construction dust, etc. off power unit.

3.For best capture of cooking impurities, your range hood should be mounted 18-24" above the cooking surface.

4.Please read specification label on product for further information and requirements.

TOOLS AND MATERIALS REQUIRED

Drill, electric or ratchet drive

1/8" drill bit for drilling pilot holes

1-1/4" wood bit for drilling electrical wiring access hole

One straight blade and one phillips head screwdriver

Pliers

Pencil and ruler and/or tape measure

Saber saw or keyhole saw for cutting 1" x 2" wood strips to length and cutting wall or cabinet openings

Caulking, metal snips, duct tape, duct (with elbows and transition, if necessary) and roof or wall cap, as required

Electrical wiring and supplies of type to comply with local codes

The following materials are required only for installations on recessed bottom kitchen cabinets:

Two 1" x 2" x 12" (approximate length) wood strips (purchase locally)

Four 1-1/4" long flat head wood screws (purchase locally)

INSTALLER: Leave This Manual With Homeowner HOMEOWNER: Use and Care Information on Page 6

PLANNING DUCTWORK INSTALLATION

(This section for UXT2030AA, UXT2036AA, UXT3030AA, and UXT3036AA hoods only. UXT4030AA and UXT4036AA hoods skip this section and go on to "Prepare the Hood".)

Begin planning ductwork by deciding where duct will run between the range hood and the outside. For best performance, use the shortest possible duct run and a minimum numaber of elbows. There are several choices shown - FIGS. A - F below.

FIG. A

Ducting directly through the wall (for range hoods mounted on an exterior wall). Shown are two ways to duct through an outside wall. If a wall cap is used directly off the back of the hood, special care must be taken to make sure that the damper in the damper/duct connector on the hood damper in the wall cap do not interfere with each other when the hood is operating. This could result in either inadequate air delivery or backdrafts. If this condition does exist, remove the hood damper flap. Sometimes when using a wall cap it is easier to duct vertically and then use an elbow as shown FIG. B.

In more complex ducting situations, a 3-1/4" x 10" rectangular ducting range hood (UXT3030AA and UXT3036AA hoods) can be converted to a round duct by means of a transition.

FIG. C. Straight up through the roof using 7" round duct (for single story installations - UXT2030AA and UTX2036AA only)

FIG. D. Ducting straight up through the roof using 3¼" x 10" rectangular duct. (For single story installations UXT3030AA and UXT3036AA hoods only.)

FIG. E. Ducting between the ceiling joists (for multi-story installations) or through the soffit space above the cabinets (where the soffit connects to an outside wall).

PREPARE THE HOOD

FIG. F. Straight up through the roof using 6" round duct (for single-story installations).

1.Unpack hood and check contents. You should receive:

1- Aluminum Filter (UXT3030AA, UXT3036AA, UXT2030AA and UXT2036AA hoods only)

1- 3¼" x 10" Damper/Duct Connector (mounted inside of hood for shipping only) ((UXT3030AA and UXT3036AA

hoods only)

1- Ductfree Filter (UXT4030AA and UXT4036AA hoods only)

2.Remove wiring box cover. Under cover find:

1- Plastic Bag containing loose mounting hardware

FIG. 1

KEYHOLE SLOTS

DUCTFREE FILTER (UXT4030AA & UXT4036AA HOODS ONLY)

ALUMINUM FILTER (UXT3030AA, UXT3036AA, UXT2030AA, UXT2036AA)

WIRING

BOX

COVER

	DAMPER/DUCT CONNECTOR
2	(UXT3030AA & UXT3036AA HOODS ONLY)

PREPARE THE HOOD - CONT.

3. Remove top or rear electrical knockout. (FIG. 2)	5. (UXT3030AA AND UXT3036AA ONLY). Install damper/duct
FIG. 2	connector over opening made in STEP 4. Use #8B sheet metal
	screws provided. (FIG. 3)
	UXT2030AA and UXT2036AA hoods ONLY) Install Model 87
	damper (purchase separately) over opening in top of hood.

FIG. 3

4.(UXT3030AA and UXT3036AA hoods ONLY) Remove duct knockout. Insert screwdriver under edge of knockout, break tabs, and peel knockout back with pliers. (FIG. 3)

PREPARE THE INSTALLATION LOCATION

Omit STEP 1 if hood will be installed under cabinets with flush	FIG. 4
bottom.

1.(For installation on recessed bottom cabinets only)

Attach a wood filler strip at each side of recessed are under cabinet. Use two 1" x 2" strips cut to length. If recess is deeper than 1" use thicker strips. Attach strips with 1-1/4'' wood screws, 3" from end end of strip. See FIG. 4.

2.Measure and mark the following (FIGS. 5A & 5B): a.) Electrical wiring opening in wall or cabinet.

b.) Duct opening in wall or cabinet. (UXT2030AA, UXT2036AA, UXT3030AA, and UXT3036AA ONLY)

FIG. 5A	FIG. 5B
	UXT3030AA
	UXT3036AA
	UXT4030AA
	UXT4036AA
	UXT2030AA
	UXT2036AA
	3