Whirlpool TT14DKXKQ00 User Manual

TOP-MOUNT

REFRIGERATOR

Use & Care Guide

For questions about features, operation/performance,

parts accessories or service, call:

In Canada, call for assistance 1-800-461-5681, for installation

and service, call: 1-800-807-6777 or visit our website at...

www.estateappliances.com

1-800-253-1301

RÉFRIGÉRATEUR

SUPERPOSÉ

Guide d’utilisation

et d’entretien

Au Canada, pour assistance, composer le 1-800-461-5681, pour

installation ou service 1-800-807-6777 ou visitez notre site web à

www.estateappliances.com

Table of Contents/Table des matières..............................2

2215168

TABLE OF CONTENTS

TABLE DES MATIÈRES

REFRIGERATOR SAFETY.......................................................... 3

Proper Disposal of Your Old Refrigerator....................................3

INSTALLATION INSTRUCTIONS ..................................................4

Unpacking Your Refrigerator .......................................................4

Location Requirements................................................................4

Electrical Requirements ...............................................................5

Connecting the Refrigerator to a Water Source ..........................5

Refrigerator Doors: Removing,

Reversing (optional) and Replacing ............................................. 7

Door Closing and Alignment ........................................................8

Normal Sounds ............................................................................9

REFRIGERATOR USE....................................................................9

Ensuring Proper Air Circulation....................................................9

Setting the Control(s) .................................................................10

Adjusting Control Settings .........................................................10

Ice Maker....................................................................................10

REFRIGERATOR FEATURES ......................................................11

Refrigerator Shelves...................................................................11

Meat Drawer and Cover.............................................................11

Crisper and Crisper Cover .........................................................12

Utility or Egg Bin.........................................................................12

FREEZER FEATURES..................................................................12

Freezer Shelf ..............................................................................12

DOOR FEATURES........................................................................13

Drop-in Door Rails......................................................................13

REFRIGERATOR CARE ...............................................................13

Cleaning......................................................................................13

Changing the Light Bulb ............................................................13

Power Interruptions....................................................................14

Vacation and Moving Care.........................................................14

TROUBLESHOOTING ..................................................................14

ASSISTANCE OR SERVICE.........................................................17

In the U.S.A. ...............................................................................17

In Canada ...................................................................................17

Accessories................................................................................17

WARRANTY .............................................................................. 18

SÉCURITÉ DU RÉFRIGÉRATEUR ...........................................19

Mise au rebut de votre vieux réfrigérateur.................................19

INSTRUCTIONS D’INSTALLATION.............................................20

Déballage de votre réfrigérateur ................................................20

Emplacement d’installation........................................................20

Spécifications électriques ..........................................................21

Raccordement du réfrigérateur à une canalisation d’eau .........21

Portes du réfrigérateur : Démontage,

inversion (option) et réinstallation...............................................23

Fermeture et alignement des portes..........................................25

Sons normaux ............................................................................25

UTILISATION DU RÉFRIGÉRATEUR ..........................................26

Pour s’assurer d’une circulation d’air appropriée......................26

Réglage des commandes ..........................................................26

Ajustement des réglages de commande...................................26

Machine à glaçons .....................................................................27

CARACTÉRISTIQUES DU RÉFRIGÉRATEUR ...........................27

Tablettes du réfrigérateur...........................................................27

Bac à viande et couvercle ..........................................................28

Bac à légumes et couvercle .......................................................28

Casier utilitaire ou oeufrier..........................................................29

CARACTÉRISTIQUES DU CONGÉLATEUR...............................29

Clayette du congélateur.............................................................29

CARACTÉRISTIQUES DE LA PORTE .........................................29

Tringles dans la porte.................................................................29

ENTRETIEN DU RÉFRIGÉRATEUR ............................................30

Nettoyage ...................................................................................30

Remplacement de l’ampoule d’éclairage ..................................30

Pannes de courant .....................................................................31

Entretien avant les vacances ou lors d’un déménagement.......31

DÉPANNAGE.................................................................................32

ASSISTANCE OU SERVICE.........................................................34

Aux États-Unis............................................................................34

Au Canada..................................................................................34

Accessoires ................................................................................34

GARANTIE.................................................................................35

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or

“WARNING.” These words mean:

You can be killed or seriously injured if you don't immediately follow instructions.

can be killed or seriously injured if you don't

You follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

WARNING:

precautions:

■

happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Disconnect power before servicing.

Replace all panels before operating. Remove doors from your old refrigerator.

■

Use nonflammable cleaner.

■

Keep flammable materials and vapors, such as gasoline, away from refrigerator.

■

Use two or more people to move and install refrigerator.

■

Disconnect power before installing ice maker (on ice maker kit ready models only).

■

Use a sturdy glass when dispensing ice or water (on some models).

SAVE THESE INSTRUCTIONS

Proper Disposal of Your

Old Refrigerator

WARNING

Suffocation Hazard Remove doors from your old refrigerator. Failure to do so can result in death or

brain damage.

IMPORTANT: Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous – even if they will sit for “just a few days.” If you are getting rid of your old refrigerator, please follow these instructions to help prevent accidents.

Before you throw away your old refrigerator or freezer:

Take off the doors.

■

Leave the shelves in place so that children may not easily

■

climb inside.

INSTALLATION

Location Requirements

INSTRUCTIONS

Unpacking Your Refrigerator

WARNING

Excessive Weight Hazard

Use two or more people to move and install refrigerator.

Failure to do so can result in back or other injury.

Removing packaging materials

Remove tape and glue residue from surfaces before turning

■

on the refrigerator. Rub a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry.

Do not use sharp instruments, rubbing alcohol, flammable

■

fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your refrigerator. For more information, see the “Refrigerator Safety” section.

On some models, shelves, bins, door shelf rails, and other

■

feature parts may be packaged in the Interior FeaturePak. Follow the instructions contained in the package for proper assembly.

Depending on your model, to remove the protective

■

(transparent) film that is on the nameplate, which is located on the freezer handle, use your fingernail and peel off the film, starting from one side and peeling to the other.

IMPORTANT:

is located behind the control panel on the ceiling of the refrigerator (on some models). The insert is part of the refrigerator and not part of the packing material. If the insert is removed, ice may migrate down from the freezer and cause icicles to form.

Do not remove the white foam air return insert that

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

■ To ensure proper ventilation for your refrigerator, allow for a

¹⁄₂ in. (12.70 mm) space on each side. Allow 3 in. (7.5 cm) of space between overhead cabinets and

■

refrigerator top.

■ Allow at least 1 in. (25.40 mm) between back of cabinet and

the wall.

3" (7.5 cm)

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for cleaning or service, be sure to protect the floor. Always pull the refrigerator straight out when moving it. Do not wiggle or “walk” the refrigerator when trying to move it, as floor damage could occur.

Cleaning before use

After you remove all of the package materials, clean the inside of your refrigerator before using it. See the cleaning instructions in the “Refrigerator Care” section.

Important information to know about glass shelves and covers:

Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. For your protection, tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use special care when removing them to avoid impact from dropping.

2" (5.08 cm)

If your refrigerator has an ice maker, make sure you leave

■

some extra space at the back for the water line connections. If you are installing your refrigerator next to a fixed wall, leave

■

2 in. (5.08 cm) minimum on the hinge side (depending on your model) to allow for the door to swing open.

Level the refrigerator (see “Door Closing and Alignment”).

■

Do not install the refrigerator near an oven, radiator, or

NOTE:

other heat source, nor in a location where the temperature will fall below 40°F (5°C).

Electrical Requirements

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in

death, fire, or electrical shock.

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical connection:

Recommended grounding method

A 115 Volt, 60 Hz., AC only 15 or 20 ampere fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an extension cord.

Before performing any type of installation, cleaning, or

NOTE:

removing a light bulb, turn the control (Thermostat, Refrigerator or Freezer Control depending on the model) to OFF and then disconnect the refrigerator from the electrical source. When you are finished, reconnect the refrigerator to the electrical source and reset the control (Thermostat, Refrigerator or Freezer Control depending on the model) to the desired setting.

Connecting the Refrigerator

to a Water Source

Read all directions carefully before you begin. IMPORTANT:

If operating the refrigerator before installing the water

■

connection, turn ice maker to the OFF position to prevent operation without water.

■ All installations must be in accordance with local plumbing

code requirements.

■ Use copper tubing and check for leaks.

■ Install copper tubing only in areas where temperatures will

remain above freezing. It may take up to 24 hours for your ice maker to begin

■

producing ice.

Tools required:

■ Standard screwdriver

■ ⁷⁄₁₆ in. and ¹⁄₂ in. open-end wrenches or two adjustable

wrenches ¹⁄₄ in. nut driver

■

¹⁄₄ in. drill bit

■

Hand drill or electric drill (properly grounded)

■

Your refrigerator dealer has a kit available with a

NOTE:

¹⁄₄ in. (6.35 mm) saddle-type shut-off valve, a union, and copper tubing. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes. Do not use a piercingtype or ³⁄₁₆ in. (4.76 mm) saddle valve which reduces water flow and clogs more easily.

Cold Water Supply

The ice maker water valve contains a flow washer which is used as a water pressure regulator. The ice maker needs to be connected to a cold water line with water pressure between 30 and 120 psi. If a problem occurs, call your utility company.

Connecting to water line:

Unplug refrigerator or disconnect power.

Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water. Find a ¹⁄₂ in. (12.7 mm) to 1¹⁄₄ in. (3.18 cm) vertical COLD

water pipe near the refrigerator.

Horizontal pipe will work, but the following procedure

NOTE:

must be followed: Drill on the top side of the pipe, not the bottom. This will help keep water away from the drill. This also keeps normal sediment from collecting in the valve.

To determine the length of copper tubing you will need,

measure from connection on lower left rear of refrigerator to water pipe. Add 7 feet (2.1 m) to allow for moving refrigerator for cleaning. Use ¹⁄₄ in. (6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

5. Using a grounded drill, drill a ¹⁄₄ in. (6.35 mm) hole in the cold

water pipe you have selected.

1. Cold Water Pipe

2. Pipe Clamp

3. Copper Tubing

4. Compression Nut

5. Compression Sleeve

6. Shut-Off Valve

7. Packing Nut

6. Fasten shut-off valve to cold water pipe with pipe clamp. Be

sure outlet end is solidly in the ¹⁄₄ in. (6.35 mm) drilled hole in the water pipe and that washer is under the pipe clamp. Tighten packing nut. Tighten the pipe clamp screws carefully and evenly so washer makes a watertight seal. Do not overtighten or you may crush the copper tubing, especially if soft (coiled) copper tubing is used. Now you are ready to connect the copper tubing.

7. Slip compression sleeve and compression nut on copper

tubing as shown. Insert end of tubing into outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten.

8. Place the free end of the tubing into a container or sink, and

turn ON main water supply and flush out tubing until water is clear. Turn OFF shut-off valve on the water pipe. Coil copper tubing.

Connecting to refrigerator: NOTE: The first step for connecting the water line to your

refrigerator is different depending on the type of water valve provided with your refrigerator. See the diagrams below to determine the style of valve you have. (On kit models, assemble water valve to refrigerator per kit instructions.)

1. For Style 1, disconnect the tube clamp on the back of the

product and insert the copper tubing through the clamp, as shown. Remove the tape label from the valve inlet and insert copper tubing until it bottoms out (approximately ³⁄₄ in. [1.9 cm]). Tighten nut by hand as much as possible; then turn the nut an additional ¹⁄₂ turn using a wrench. Do not overtighten. Re-attach the tube clamp and tube to the back of the cabinet. Skip to Step 2.

For Style 2, disconnect the tube clamp on the back of the product and insert copper tubing through the clamp as shown. Attach the copper tube to the valve inlet using a compression nut and sleeve as shown. Tighten the compression nut. Do not overtighten. Re-attach the tube clamp and tube to the back of the cabinet. Move to Step 2.

2. Turn shut-off valve ON. Check For Leaks. Tighten any connections (including connections at the valve) or nuts that leak.

Style 1

1. Tube Clamp

2. Copper Tubing

3. Compression Nut

4. Valve Inlet

Style 2

1. Tube Clamp

2. Copper Tubing

3. Compression Nut

3. The ice maker is equipped with a built-in water strainer. If

local water conditions require periodic cleaning or a well is your source of water supply, a second water strainer should be installed in the ¹⁄₄ in. (6.35 mm) water line. Obtain a water strainer from your nearest appliance dealer. Install at either tube connection.

4. Plug in refrigerator or reconnect power.

Refrigerator Doors: Removing, Reversing (optional) and Replacing

TOOLS NEEDED: ⁵⁄₁₆ in. hex-head socket wrench, No. 2 Phillips screwdriver, flat-head screwdriver, ⁵⁄₁₆ in. open-end wrench, flat 2 in. putty knife.

IMPORTANT: Before you begin, turn the refrigerator control OFF, unplug refrigerator or disconnect power. Remove food from doors.

Door Removal &

Replacement

Top Hinge

1. 5/16" Hex-Head Hinge Screws

2. Top Hinge

3. Spacer

Center Hinge

1. Door Stop

2. Door Stop Screw

3. Spacer

4. Center Hinge

5. 5/16" Hex-Head Hinge Screws

6. Spacer

Bottom Hinge

Door Swing Reversal (optional)

1. Cabinet Hinge Hole Plugs

1. Door Hinge Hole Plug

1. Flat-Head Handle Screws

2. Freezer Handle

1-2

1-1

/16" Hex-Head Hinge

Screws and Washers

1. Door Stop

2. Spacer

3. Door Stop Screw

4. Bottom Hinge

5. 5/16" Hex-Head Hinge Screws

1. Door Handle Sealing Screws

Front View

1. Door Stop Screw

2. Door Stop

Side View

1. Door Handle Seal Screw Front

1. Flat-Head Handle Screw

2. Refrigerator Handle

3. Handle Screw

4. Screw Cover

Door and hinge removal

in. Hex-Head Hinge Screw

⁵⁄₁₆

Unplug refrigerator or disconnect power.

Keep both doors closed until you are ready to lift them free

from the cabinet.

Provide additional support for the doors while the

NOTE:

hinges are being moved. Do not depend on the door magnets to hold the doors in place while you are working.

Remove the parts for the top hinge as shown in Top Hinge

graphic. Lift the freezer door free from the cabinet.

Remove the parts for the center hinge as shown in the Center

Hinge graphic. Lift the refrigerator door free from the cabinet.

Remove the parts for the bottom hinge as shown in the

Bottom Hinge graphic.

IMPORTANT: If you want to reverse your doors so that they open in the opposite direction, follow these steps. If you are not reversing the doors, see “Door and Hinge Replacement.”

Door reversal (optional)

Door Stop Screw Door Hinge Hole Plug

Door Handle Sealing Screw Cabinet Hinge Hole Plug

Flat-Head Handle Screw Door Handle Screw Cover

Door Handle Seal Screw Front Round-Head Handle Screw

Cabinet

Remove

move them to opposite side (see Graphic 1-1). Remove cabinet hinge hole plugs from cabinet top and move

them to opposite side hinge holes as shown (see Graphic 1-

2).

Freezer door

Remove freezer handle assembly as shown. Keep all parts

together (see Graphic 2). Remove door hinge hole plug. Move to opposite side as

shown (see Graphic 3). Remove door handle sealing screws. Move to opposite side

of freezer door as shown (see Graphic 4). Remove door stop. Move to opposite side of freezer door as

shown (see Graphic 5). Position freezer handle on opposite side of freezer door.

Assemble handle on door as shown (see Graphic 2). Tighten all screws. Set aside door until hinges and refrigerator

compartment door are in place.

in. hex-head hinge screws from handle side and

⁵⁄₁₆

Refrigerator door

Remove the screw cover (see Graphic 6).

Remove refrigerator handle assembly as shown. Keep all

parts together (see Graphic 6). Remove door hinge hole plug from refrigerator door. Move to

opposite side hinge hole as shown (see Graphic 3). Remove door handle sealing screws. Move to opposite side

of refrigerator door as shown (see Graphic 4). Remove door handle seal screw front. Move to opposite side

of refrigerator door as shown (see Graphic 7). Remove door stop. Move to opposite side of refrigerator door

as shown (see Graphic 5). Position refrigerator handle on opposite side of the

refrigerator door as shown (see Graphic 6). Drive top two screws in handle first. Align lower portion of handle and drive bottom screw.

Replace screw cover (see Graphic 6).

Tighten all screws. Set aside refrigerator door until bottom

hinge is installed on product.

Door and hinge replacement

Graphic may be reversed if door swing is reversed.

NOTE:

Replace the parts for the bottom hinge as shown. Tighten

screws. Replace the refrigerator door.

Provide additional support for the doors while the

NOTE:

hinges are being moved. Do not depend on the door magnets to hold the doors in place while you are working.

Assemble the parts for the center hinge as shown and tighten

all screws (see Center Hinge graphic). Replace the freezer door.

Assemble the parts of the top hinge as shown (see Top Hinge

graphic). Do not tighten screws completely. Line up the doors so that the bottom of the freezer door

aligns evenly with the top of the refrigerator door. Tighten all screws.

Final Steps

Check all holes to make sure that hole plugs and screws are

in place. Plug in refrigerator or reconnect power.

Reset the controls (see “Setting the Controls” section).

Door Closing and Alignment

Your refrigerator has two front adjustable rollers – one on the right and one on the left. If your refrigerator seems unsteady or you want the doors to close easier, adjust the refrigerator's tilt using the instructions below:

Roll out the refrigerator and use a level to check the floor at

the back from side-to-side. If needed, use shims to level the back of the refrigerator if it is uneven. Roll the refrigerator back into place with the rear rollers on top of any shim(s) used so that the rear of the refrigerator is level.

With the rear already level and the refrigerator in place, use

the bottom leveling screws to level the refrigerator from sideto-side. They are part of the front roller assemblies, which are found at the base of the refrigerator on either side.

Having someone push against the top of the

NOTE:

refrigerator takes some weight off the leveling screws and rollers. This makes it easier to adjust the screws.

Style 1

Style 2

■ Your refrigerator is designed to run more efficiently to keep

your food items at the desired temperature. The high efficiency compressor may cause your new refrigerator to run longer than your old one, and you may hear a pulsating or high-pitched sound.

Water dripping on the defrost heater during a defrost cycle

■

may cause a sizzling sound. You may hear the evaporator fan motor circulating the air

■

through the refrigerator and freezer compartments.

■ As each cycle ends, you may hear a gurgling sound due to

the refrigerant flowing in your refrigerator.

■ Contraction and expansion of the inside walls may cause a

popping noise. You may hear air being forced over the condenser by the

■

condenser fan.

■ You may hear water running into the drain pan during the

defrost cycle.

REFRIGERATOR USE

Ensuring Proper Air Circulation

In order to ensure proper temperatures, you need to permit air flow between the refrigerator and freezer sections. As shown in the illustration, cool air enters through the bottom of the freezer section and moves up. Most of the air then flows through the freezer section vents and recirculates under the freezer floor. The rest of the air enters the refrigerator section through the top vent.

3. Depending on your model, to level your refrigerator you may

either turn the screw clockwise to raise that side of the refrigerator or turn the screw counterclockwise to lower that side. Place a level on top of the refrigerator to check adjustments.

4. If the doors do not close on their own, you will need to raise

the front of the refrigerator so it is slightly higher than the back. To do this, turn both leveling screws clockwise ¹⁄₂ turn.

IMPORTANT: Be sure to turn both screws an equal amount or the refrigerator will no longer be level side-to-side.

5. Open doors and check if they close automatically. If not,

repeat steps 3 and 4.

6. Using a level, check to see if the refrigerator is still level side-

to-side. Readjust if necessary.

Normal Sounds

Your new refrigerator may make sounds that your old one didn’t make. Because the sounds are new to you, you might be concerned about them. Most of the new sounds are normal. Hard surfaces, like the floor, walls, and cabinets, can make the sounds seem louder than they actually are. The following describes the kinds of sounds and what may be making them.

If your product is equipped with an ice maker, you will hear a

■

buzzing sound when the water valve opens to fill the ice maker for each cycle.

The defrost timer will click when the automatic defrost cycle

■

begins and ends. Also, the Thermostat Control (or Refrigerator Control depending on the model) will click when cycling on and off.

Rattling noises may come from the flow of refrigerant, the

■

water line, or items stored on top of the refrigerator.

Do not block any of these vents with food packages. If the vents are blocked, airflow will be prevented and temperature and moisture problems may occur.

IMPORTANT: Because air circulates between both sections, any odors formed in one section will transfer to the other. You must thoroughly clean both sections to eliminate odors. To prevent odor transfer and drying out of food, wrap or cover foods tightly. (See the “Refrigerator Features” section for details.)

Setting the Control(s)

WARMER

COLDER

RECOMMENDED SETTING

REFRIGERATOR

WARMER

COLDER

RECOMMENDED SETTING

FREEZER

For your convenience, your refrigerator control(s) are preset at the factory. When you first install your refrigerator, make sure that the control(s) are still preset to the mid-settings as shown.

NOTE: To turn your refrigerator off, turn the refrigerator control to

the word OFF or until the word OFF appears. Your product will not cool when the refrigerator control is set to OFF.

Mid-setting “3”

Adjusting Control Settings

The mid-settings indicated in the previous section should be correct for normal household usage. The controls are set correctly when milk or juice is as cold as you like and when ice cream is firm.

If the temperature is too warm or too cold in the refrigerator or freezer, first check the air vents to be sure they are not blocked.

If you need to adjust temperatures, use the settings listed in the chart below as a guide. On models with two controls, adjust the refrigerator temperature first. Wait at least 24 hours between

adjustments and then re-check the temperatures.

CONDITION/REASON: ADJUSTMENT:

Mid-setting “3”

WARMER

1 2

REFRIGERATOR

RECOMMENDED SETTING

4 5

COLDER

WARMER

FREEZER

RECOMMENDED SETTING

COLDER

1 2

4 5

Mid-setting “4”

REFRIGERATOR

IMPORTANT:

Give your refrigerator time to cool down completely before

■

adding food. It is best to wait 24 hours before you put food into the refrigerator.

If you add food before the refrigerator has cooled completely,

■

your food may spoil. Adjusting the Refrigerator and Freezer Controls to a higher (colder) than recommended setting will not cool the compartments any faster.

FREEZER

REFRIGERATOR section too warm

Door opened often, large

■

amount of food added or room

Adjust REFRIGERATOR or TEMPERATURE Control one setting higher

temperature very warm

FREEZER section too warm/ice not made fast enough

■ Door opened often, or large

Adjust FREEZER or TEMPERATURE Control one setting higher

amount of food added or very cold room temperature (can’t cycle often enough)

■ Heavy ice usage

REFRIGERATOR section too cold

■ Controls not set correctly for

your conditions

FREEZER section too cold

Controls not set correctly for

■

your conditions

Adjust REFRIGERATOR or TEMPERATURE Control one setting lower

Adjust FREEZER or TEMPERATURE Control one setting lower

Ice Maker

(on some models - Accessory)

To turn the ice maker on/off: NOTE: Do not force the wire shut-off arm up or down.

To turn the ice maker on, simply lower the wire shut-off arm.

■

NOTE: Your ice maker has an automatic shut-off. As ice is made, the ice cubes will fill the ice storage bin and the ice cubes will raise the wire shut-off arm to the OFF (arm up) position.

To manually turn the ice maker off, lift the wire shut-off arm to

■

the OFF (arm up) position and listen for the click to make sure the ice maker will not continue to operate.

MAX

NORMAL

To increase ice production rate:

Normal Ice Production: In normal ice production mode, the

■

ice maker should produce approximately 8 to 12 batches of ice in a 24-hour period. If ice is not being made fast enough, turn the Freezer Control toward a higher (colder) number in half number steps. (For example, if the control is at 3, move it to between 3 and 4.) Wait 24 hours and, if necessary, gradually turn the Freezer Control to the highest setting, waiting 24 hours between each increase.

Maximum Ice Production (on some models): In maximum

■

ice production, the ice maker should produce approximately 16 to 20 batches of ice in a 24-hour period. If your refrigerator has the maximum ice production feature, push the switch to MAX.

REMEMBER:

■ Allow 24 hours to produce the first batch of ice. Discard the

first three batches of ice produced. The quality of your ice will be only as good as the quality of

■

the water supplied to your ice maker. Avoid connecting the ice maker to a softened water supply. Water softener chemicals (such as salt) can damage parts of the ice maker and lead to poor quality ice. If a softened water supply cannot be avoided, make sure the water softener is operating properly and is well maintained.

Do not store anything on top of the ice maker or in the ice

■

storage bin.

Refrigerator Shelves

(Glass shelves on some models)

The shelves in your refrigerator are adjustable to match your individual storage needs.

Storing similar food items together in your refrigerator and adjusting the shelves to fit different heights of items will make finding the exact item you want easier. It will also reduce the amount of time the refrigerator door is open, and save energy.

To remove and replace a shelf:

1. Remove items from the shelf.

2. Slide the shelf straight out to the stop.

3. Depending on your model, lift back or front of the shelf past

the stop. Slide shelf out the rest of the way.

4. Replace the shelf by sliding the back of the shelf into the

track in the wall of the cabinet.

5. Guide the front of the shelf into the shelf track. Be sure to

slide the shelf in all the way.

REFRIGERATOR FEATURES

Your model may have some or all of these features. Features that can be purchased separately as product accessories are labeled with the word “Accessory.” Not all accessories will fit all models. If you are interested in purchasing one of the accessories, please call the toll-free number on the cover or in the “Assistance or Service” section.

Important information to know about glass shelves and covers:

Meat Drawer and Cover

(on some models)

To remove and replace the meat drawer:

1. Slide meat drawer out to the stop.

2. Lift front of meat drawer with one hand while supporting

bottom of drawer with other hand. Slide drawer out the rest of the way.

3. Replace the drawer by sliding it back in fully past the drawer

stop.

To remove and replace the meat drawer cover (Glass meat drawer cover on some models):

1. Remove the meat drawer.

2. Push the cover back to release the rear clips from the shelf.

Tilt the cover up at the front, and pull it forward.

3. Replace the meat drawer cover by fitting the notches and

clips on underside of the cover over the rear and center crossbars on the shelf.

4. Lower cover into place and pull the cover forward to secure

the rear clips onto the shelf.

5. Replace the meat drawer.

+ 25 hidden pages