Whirlpool TRAK SYMPHONY INSTRUCTION FOR USE
Contents
Quick Reference Guide
Programme Chart
Preparing the Laundry
Selecting a Programme and Options
Starting and Completing a Programme
Changing a Programme
Interrupting a Programme
Daily Maintenance and Cleaning
Instructions for Use
Booklet
Before Using the Dryer / Connections
Precautions and General
Recommendations
Description of the Dryer
Vent Connection
Door Reversibility
Troubleshooting Guide / After-Sales
Service
Before Using the Dryer / Connections
1. Removing the
packaging and check
After unpacking, make sure
that the dryer is
undamaged. If in doubt, do
not use the dryer. Contact
After-Sales Service or your
local retailer.
Keep the packaging
materials (plastic bags,
polystyrene parts, etc.) out
of reach of children, as they
are potentially dangerous.
2. Electrical Connections
Electrical connections must
be carried out by a qualified
technician in compliance
with the manufacturers
instructions and current
standard safety regulations.
Electrical connection must
comply with local Electricity
Board regulations.
Voltage information, power
consumption and the
required fuse protection is
shown on the rating plate
mounted at the rear of the
dryer.
The manufacturer cannot
accept any liability for
personal injury or damage
to property resulting from
failure to adhere to these
instructions.
The dryer must be earthed
as prescribed by law.
Do not use extension leads
or multiple adaptors.
Before any maintenance on
the dryer disconnect it from
the mains supply.
Do not operate the dryer if
it has been damaged during
transport. Contact one of
our After-Sales Service
technicians.
Mains cables must be
replaced by an original
cable and is only to be
carried out by a technician
from After-Sales Service or
an authorized electrician.
After installation access to
the mains plug has to be
guaranteed, or the all-pole
disconnection has to be
possible with a switch.
3. Installation
Do not install your dryer
where it can be subject to
extreme conditions, such as:
poor ventilation,
temperatures around
freezing (or above 35° C).
Remove the protective foil
from the control panel.
Stability:
When installing the dryer
always carefully level the
dryer adjusting the two
feet and check the correct
levelling with a spirit level.
To built in the dryer
For security reason do not
remove the worktop.
Connect the dryer to an
external ventilation system
in order to prevent steam
from damaging your
furniture during the years.
Stacking kit
Your dryer can be stacked
on top of your front
loading washing machine.
To do this, use stacking kit
AMH 752, available at your
dealer.
Minimum housing
dimensions:
Width: 600 mm
Height: 850 mm
Depth: 560 mm
Precautions and General Recommendations
1. Packing
The packing box may be
fully recycled as confirmed
by the recycling symbol.
2. Energy saving tips
Always dry a full load:
depending on the type of
laundry and the
programme/drying time.
By preference use the
maximum spin speed
allowed by your washing
machine, since draining the
water mechanically requires
less energy.
Do not overdry the laundry.
Clean the lint filter after
drying cycle.
every
Place your dryer in a room
with a temperature
between 15° C and 20° C. In
case of higher temperature
ventilate the room.
Always select the correct
programme/drying time for
the load in order to obtain
the desired drying results.
Select the gentle option
only with small loads.
When drying cotton, for
example: dry iron dry and
cupboard dry loads
together. Start with the iron
dry programme/drying time
setting, remove the laundry
to be ironed at the end of
that cycle and dry the
remainder of the load on
the cupboard dry setting.
3. Disposing of packaging
and old appliances
The dryer is built from
reusable materials. The
dryer must be disposed of
in compliance with local
waste disposal regulations.
Before scrapping, cut off
the power cable so that the
dryer cannot be connected
to the mains.
4. Child safety
Children must not be
allowed to play with the
dryer.
5. General
recommendations
Always set the programme/
time selector knob to the
0 position after use. This
prevents the dryer from
being switched on
accidentally.
Before cleaning or carrying
out maintenance, switch off
the dryer and disconnect it
from the mains supply.
To clean the outside of the
dryer, use a neutral
detergent and a damp
cloth.
Do not use abrasive
detergents.
Clean the lint filter at
the end of every drying
cycle:
Open the door.
1.
Pull the filter upwards.
2.
Remove lint using a soft
3.
brush or your fingertips.
Push the filter firmly back
4.
into place.
Wipe away lint from the
door seal and the door
using a damp cloth.
If the lint filter mesh is
clogged, clean it with water
and a soft brush.
If necessary, the power
cable may be replaced with
an identical one obtained
from our After-Sales
Service. The power cable
must only be replaced by a
qualified technician.
EC Declaration of
Conformity
This dryer has been
designed, constructed and
distributed in compliance
with the safety
requirements of EC
Directives:
73/23/EEC Low Voltage
Directive
89/336/EEC EMC Directive
93/68/EEC CE Marking
Directive.
The dryer must be used in
the household for the
described uses.
Loading...