Whirlpool TGW 5500 SW User Manual
4gb66005.fm5 Page 12 Monday, January 28, 2002 5:04 PM
Instructions for use
Before using the hob
Installation - Technical information for the
Installer
Electrical connection
Connection to gas supply - RC 3/8 ( ISO 7/1
- RC 3/8)
Energy saving tips
Protecting the environment
Precautions and general recommendations
Care and maintenance
Troubleshooting Guide
After Sales Service
National Safety regulations
12
4gb66005.fm5 Page 13 Monday, January 28, 2002 5:04 PM
Before using the hob
To make the most of your
new appliance, please read
the user instructions
carefully and keep them to
hand for future
consultation.
Installation - Technical information for the Installer
Cooktop
The cooktop must be set
into a worktop between
30 mm and 50 mm deep.
If there is no oven
beneath the cooktop,
insert a separator panel
at a minimum distance
of 20 mm from the
bottom of the hob.
If there is an oven
installed under the
cooktop, make sure that
it is manufactured by us
and equipped with a
cooling system.
Note: After installation, make
sure the cooktop power cable
does not come into contact
with the metal burner box
and the oven (if installed)
with tangential fan below it.
If the cooktop is to be
installed next to a
column unit, leave a
distance of at least
250 mm from the edge
of the hob.
The outer surfaces of
the furniture or
appliances next to the
cooktop must be heat
resistant (heat
protection Y,
according to local
standards).
Installation must comply
with current local
regulations.
In the room where the
cooktop is installed, there
must be enough air to
allow the gas to burn
correctly.
The natural flow of air
must take place through
an adequate opening, that
must be:
- permanent, made on one
of the outside walls of the
room and communicating
with the exterior in the
area away from sources of
pollution;
- built so as to ensure that its
openings, both on the
inside and on the outside,
cannot be obstructed,
intentionally or
accidentally;
- protected by a metal grid
or mesh that does not
reduce its working section;
- situated near the floor
level and positioned so as
not to interfere with the
operation of the fume
exhaust devices.
0
5
n
i
m
13
4gb66005.fm5 Page 14 Monday, January 28, 2002 5:04 PM
Installation - Technical information for the Installer
Assembly
The installation of the
cooktop must be carried
out without grids to
avoid any deformation
of the appliance.
Position the brackets
into the relevant holes
and tighten by means of
the screws supplied.
Make an opening in the
worktop, respecting the
dimensions indicated in
the separate Product
Description Sheet.
Also make sure that
there is a ventilation
opening at both sides of
50 mm min. as shown.
Electrical connection
Apply the gasket
supplied along the
outer perimeter of the
worktop, as shown in
the figure.
Make sure that
ventilation openings
are provided (see
figure).
Position the brackets in
the holes and tighten
with the screws
supplied.
Install the cooktop into
the worktop.
Installation must be carried
out in compliance with the
regulations of the local
electricity supply company.
Make sure that the voltage
indicated on the rating plate
corresponds to the voltage in
your home. Regulations
require that the appliance is
earthed: use conductors
(including the earth
conductor) of the appropriate
size only. The manufacturer
declines all responsibility for
injury to persons or animals
and for damage to property
resulting from failure to
observe the above regulations.
14
The appliance must be
connected to the electricity
supply by means of an all-
pole disconnect switch
with minimum contact gap
of 3 mm.
If necessary, the electrical
power cable must be replaced
exclusively with a power cable
having identical characteristics
to the original supplied by the
manufacturer.
This operation must be
performed by the After Sales
Service or a qualified
electrician.
Warning
cable must be long enough to
allow the cooktop to be
removed from the worktop
and must be positioned so as
to avoid damage or
overheating caused by contact
with the base.
: the power supply
Loading...