WHIRLPOOL SW8 1Q XW Daily Reference Guide
Quick guide
high temp.
med-high temp.
medium temp.
med-low temp.
low temp.
high temp.
med-high temp.
medium temp.
med-low temp.
low temp.
on - o
EN
THANK YOU FOR BUYING A WHIRLPOOL PRODUCT
In order to receive a more complete assistance, please
register your product on www . whirlpool . eu/ register
PRODUCT DESCRIPTION
FIRST TIME USE
Wait at least two hours, after the installation, before connecting the
appliance to the power supply.
Connect the appliance to the power supply and turn the thermostat
knob to switch on the appliance.
CONTROL PANEL
1.
4.
Before using the appliance carefully read the Safety
Instruction.
After turning the appliance on, you must wait for 4‑6 hours for the
correct storage temperature to be reached for a normally lled
appliance. Position the antibacterial anti‑odour lter in the fan as
demonstrated in the lter packaging (if available).
1. 6Th Sense
2. Fast Cooling button
3. Temperature button
4. Indicator LEDs
2.
3.
6TH SENSE
This function automatically works to ensure the optimal conditions to
preserve the stored food.
th
Sense” function is automatically activated when:
The “6
• a large amount of food is loaded into the refrigerator
• the refrigerator door is left open for a long time
• a prolonged power failure takes place, causing the internal
temperature of the appliance to increase to values that cannot
guarantee safe storage of food.
FAST COOLING BUTTON
The use of the Fast Cooling function is recommended:
• to increase the cooling speed of the refrigerator compartment
when placing a very high quantity of food within it,
To activate the Fast Cooling function, press and hold for 3seconds the
Temperature button on the control panel till all the 3 LEDs will turn on.
The function is automatically deactivated after 6 hours and return to
previous selected set point. The function can be manually deactivated
by pressing and holding for 3 seconds the Temperature button on the
control panel.
TEMPERATURE BUTTON
Press the Temperature button on the control panel to adjust the
temperature from the warmest through the lower to the coldest level.
Pressing the Temperature button, the temperature setting will change
cyclically. At rst plug‑in of appliance temperature setpoint is present
at medium position (factory setting).
Following table shows temperature setpoints::
High temp.
Note: Displayed set points correspond to the average temperature
throughout the whole refrigerator.
INDICATOR LEDS
To display the current temperature setpoint or the Fast Cooling
function.
REFRIGERATOR LIGHT
The light system inside the refrigerator compartment uses LEDs light,
allowing a better lightning as well as a very low energy consumption.
If the LED light system does not work, please contact the Service to
replace it.
Important: The refrigerator compartment light switches on when the
refrigerator door is opened. If the door is kept open for more then 8
minutes the light will be automatically switched o.
FAN
The fan improves temperature distribution inside the refrigerator
compartment, allowing better preservation of stored food. By default,
the fan is switched on. It is advisable to keep the fan switched on, so
that the “6
th
Sense” function can work properly and also when the
ambient air temperature is above 27 ‑ 28°C or if you notice drops of
water on the glass shelves or in sever humidity
conditions. To turn o the fan press the button of fan.
Please note that when the fan is switched on it will not
continuously work. The fan will start/stop working
depending on the temperature and/or humidity level
inside the fridge. It is therefore absolutely normal if the
fan does not move even if the fan is switched on.
Led ON Led OFF
Med‑high temp.
Medium temp.
Med‑low temp.
Low temp.
UTILISATION AND MAINTENANCE OF THE WATER DISPENCER AND FILTER
WATER DISPENSER
FIRST USE
The rst time you use the water dispenser or after a long period left
not used wash the tank and the lter with water. The water dispenser
provides fresh, ltered water, without the need of opening the
refrigerator door. This will reduce the number of times the door is
opened, thus also reducing energy consumption of the product.
To ll the tank, rotate the cap in the direction of the arrow.
1. Water tank (g. 1)
The water tank is made of antibacterial material. This prevents
and reduces the proliferation of bacteria. An internal container,
with an active carbon ltered ensures water ltration. To ll the
tank: rotate the water inlet towards you and ll with water, using
a jug or other suitable container. Once the tank is full, close the
water inlet by moving it back to its original position. Always
use drinking water only: any other liquid may impair product
performance.
FITTING AND REPLACING THE ACTIVE CARBON FILTER
The water lter should be removed from the foil bag (found in the
crisper drawer (item 7). Follow the instructions provided with the lter.
Important: If the lter is left dry for an extended period of time, its
performance may be reduced. Immerse the lter in water for a few
seconds to reinstate optimum performance.
(g. 4) remove the internal container and the lter, and wash them
4.
separately. When washing the lter, only use clean water (no
detergent or sharp tools). To clean the disk lter, rst remove it
from the container.
Fig. 3
Tank
Fig. 1
Obtaining ltered water (g. 2)
2.
After lling the tank, the water may not be immediately available. This
is because the ltering process may require a few minutes (depending
on the amount of water in the tank). To dispense water: with the
refrigerator door closed, press the water dispenser tab with the glass.
If for safety reason water delivery must be prevented, simply press the
stop at the back of the tab. To release water delivery, move the stop
back to its original position. It is recommended to drink the supplied
water from the dispenser in 6 hours
Stop
Water drip tray
Cleaning the water tank (g. 3-4-5-6-7-8)
3.
Periodically clean the water tank with running water. Twice a year
it is recommended to keep healthy the unit using specic products
based on diluted chlorine that not modify the material properties
and rinse with current water.
To clean the tank, proceed as follows: (g. 3) release and remove
the water tank by lifting it and pulling towards you. Place the tank
on a at surface, remove and wash the top cover.
Note: the tank must be retted in its position as soon as possible, to
prevent the refrigerator from overheating.
WATER FILTER DURATION
To ensure optimum performance you should change the water lter
according with the following table:
Water consumption (average) Filter duration
.
Activation
device
Fig. 2
Fig. 4
(g. 5) for a more thorough cleaning, remove the valve cap (the
5.
tting connecting the tank to the refrigerator) by rotating it
anticlockwise. Clean the cap.
Important: do not pull on the valve body (g. 6).
Fig. 5
(g. 7) replace the valve cap by rotating clockwise.
6.
Fig. 7
(g. 8) t the tank back in place by placing it between the lateral
7.
guides of the door and pushing it in position, ensuring that the
valve is back in its original seat. Check that the there are no gaps
between the rubber seal of the tank and the door.
Fig. 8
Filter replacement is not covered by product warranty. To order more
water lter cartridges, please contact your after‑sales service.
Fig. 6
3.0 l/day 4 months
4.5 l/day 3 months
6.0 l/day 2 months
Loading...