Whirlpool SCS3017RQ05, GLT3057RB02, W3CG3014XS00, W3CG3014XW00, SCS3617RS04 Installation Guide

...
INSTALLATIONINSTRUCTIONS
30" (76 CM) AND 36" (91.4 CM)
GAS BUILT-INCOOKTOP
INSTRUCTIONS D'I_ISTALLATION
DE LA TABLEDECUISSON A GAZ ENCASTREEDE
30" (76,2 CM) ET36" (91,4 CM)
TableofContents/Table desmati@res
COOKTOP SAFETY ........................................................................ 1
INSTALLATION REQUIREMENTS ................................................ 2
INSTALLATION INSTRUCTIONS .................................................. 5
WIRING DIAGRAM ......................................................................... 9
SECURITI :!:DE LA TABLE DE CUISSON .................................... 10
EXIGENCES D'INSTALLATION ................................................... 11
Outillage et pieces ...................................................................... 11
Exigences d'emplacement ......................................................... 11
Specifications electriques .......................................................... 13
Specifications de I'alimentation en gaz ..................................... 13
INSTRUCTIONS D'INSTALLATION ............................................. 15
Preparation de la table de cuisson pour I'installation ................ 15
Installation de la table de cuisson .............................................. 15
Raccordement au gaz ................................................................ 16
Fixation de la table de cuisson au plan de travail ...................... 17
Achever I'installation .................................................................. 18
SOHI_MAS DE CABLAGE ............................................................ lg
COOKTOP SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.
iMPORTANT:
Installer: Leave installation instructions with the homeowner.
Homeowner: Keep installation instructions for future reference.
iMPORTANT :
Installateur : Remettre les instructions d'installation au preprietaire. Propdetaire : Conserver les instructions d'installation pour reference ulterieure.
W10131955A
may result causing property damage, personal injury or death,
I WARNING: If the information in this manual is not followed exactly, a fire or explosion I
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance,
- WHAT TO DO IF YOU SMELL GAS:
Do not try to light any appliance,
Do not touch any electrical switch,
Do not use any phone in your building,
Immediately call your gas supplier from a neighbor's phone, Follow the gas supplier's
instructions,
If you cannot reach your gas supplier, call the fire department,
- Installation and service must be performed by a qualified installer, service agency or the gas supplier,
In the State of Massachusetts, the following installation instructions apply:
Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by the State of Massachusetts.
If using a ball valve, it shall be a T-handle type.
A flexible gas connector, when used, must not exceed 3 feet.
I
I
INSTALLATIONREQUIREMENTS
Gather the required tools and parts before starting installation. Tools needed
Tape measure
Flat-blade screwdriver
1¾6"combination wrench
Pipe wrench
Wrench or pliers
Parts supplied
Gas pressure regulator
Burner grates
Burner caps
Clamping brackets (2)
21/2'' (6.4 cm) clamping screws (2)
Parts needed
Check local codes and consult gas supplier. Check existing gas supply and electrical supply. See "Electrical Requirements" and "Gas Supply Requirements" sections.
Marker or pencil
Pipe-joint compound resistant to LP gas
Noncorrosive leak-detection solution
IMPORTANT: Observe all governing codes and ordinances. Do not obstruct flow of combustion and ventilation air.
It is the installer's responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located on the underside of the cooktop base.
oo
o
o A
S
A. Model/serial rating plate
To eliminate the risk of burns or fire by reaching over heated surface units, cabinet storage space located above the surface units should be avoided. If cabinet storage is to be provided, the risk can be reduced by installing a range hood that projects horizontally a minimum of 5" (12.7 cm) beyond
the bottom of the cabinets. The cooktop should be installed in a location away from
strong draft areas, such as windows, doors and strong heating vents or fans.
Allopeningsinthewallorfloorwherecooktopistobe installedmustbesealed.
Cabinetopeningdimensionsthatareshownmustbeused. Givendimensionsareminimumclearances.
Groundedelectricalsupplyisrequired.See"Electrical Requirements"section.Propergassupplyconnectionmust beavailable.See"GasSupplyRequirements"section.
Thecooktopisdesignedtohangfromthecountertopbyits sideorrearflanges.
Thegasandelectricsupplyshouldbelocatedasshownin "InstallationClearances"sectionsothattheyareaccessible withoutrequiringremovalofthecooktop.
Providecutoutinrightrearcornerofcutoutenclosureas showntoprovideclearanceforgasinlet,powersupplycord, andtoallowtheratinglabeltobevisible.
IMPORTANT:Toavoiddamage,checkwithyourbuilderor cabinetsuppliertomakesurethatthematerialsusedwillnot discolor,delaminateorsustainotherdamage.
Mobile Home - Additional Installation Requirements The installation of this cooktop must conform to the
Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280). When such standard is not applicable, use the Standard for Manufactured Home Installations, ANSI A225.1/NFPA 501A or with local codes.
In Canada, the installation of this cooktop must conform with the current standards CAN/CSA-A240-1atest edition, or with local
codes.
Curved-edge glass cooktops
y........................B.....................
A. 21_" (53.7 cm) B. 30_6" (77.0 cm) on 30" (76.2 cm) models,
36_J' (92.3 cm) on 36" (91.4 cm) models
C. 2z_'' (7.3 cm)
Installation Clearances
I_-_ A I
M
Product Dimensions
Metal Cooktops
A. 21_" (53.4 cm)
B. 31 z_6"(79.8 cm) on 30" (76.2 cm) models,
37_G" (95.4 cm) on 36" (91.4 cm) models
C. 2 _" (7.3 cm)
Straight-edge glass cooktops
A
A. 20_G" (51.5 cm) B. 30_6" (76.8 cm) on 30" (76.2 cm) models,
36_6" (92.5 cm) on 36" (91.4 cm) models
C. 2 _" (7.3 cm)
A. 30" (76.2 cm) on 30" models," 36" (91.4 cm) on 36" models B. Combustible area above countertop (shown by dashed box
above)
C. 30" (76.2 cm) minimum clearance between top of coektop
platform and bottom of unprotected wood or metal cabinet
(24" [61 cm] minimum clearance if bottom of wood or metal cabinet is protected by not less than V4"[0.6 cm] flame
retardant mlllboard covered with not less than No. 28 MSG sheet steel, 0.015" [0.04 cm] stainless steel, or
0.024 [0.06 cm] aluminum or 0.020 [0.05 cm] copper)
D. 13" (33 cm) recommended upper cabinet depth
E. 2_" (5.4cm) F 19" (48.3 cm)
G. 18" (45.7 cm) minimum clearance from upper cabinet to
countertop within minimum horizontal clearances to cooktop
H. Grounded outlet - Locate within 24" (61 cm) of right rear
corner of cutout
C
L 29" (73.7 cm) on 30" models; 35_/4'' (89.5 cm) on 36" models
J. 8_" (21.3 cm) minimum distance to nearest left and right side
combustible surface
K. 2_" (7.3 cm) minimum distance to rear combustible surface
L. Gas line opening - Wall: anywhere 5" (12.7 cm) below
underside of countertop. Cabinet floor: anywhere within
6" (!5.2 cm) of rear wall is recommended
M. 24" (61 cm) minimum countertop depth is required
NOTES: After making the countertop cutout, some installations may require notching down the base cabinet side walls to clear
the cooktop base. To avoid this modification, use a base cabinet with sidewalls wider than the cutout.
Ifcabinethasadrawer,a4"(10.2cm)depthclearancefromthe countertoptothetopofthedrawer(orotherobstruction)inbase cabinetisrequired.Thedrawerdepthmayneedtobeshortened toavoidinterferingwiththeregulator.
Ifinstallingarangehoodormicrowavehoodcombinationabove thecooktop,followtherangehoodormicrowavehood
combinationinstallationinstructionsfordimensionalclearances abovethecooktopsurface.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong. Do not use an adapter.
Do not use an extension cord, Failure to follow these instructions can result in death,
fire, or electrical shock.
IMPORTANT: The cooktop must be electrically grounded in
accordance with local codes and ordinances, or in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70 or Canadian Electrical Code, CSA C22.1,
This cooktop is equipped with an electronic ignition system that will not operate if plugged into an outlet that is not properly
polarized. If codes permit and a separate ground wire is used, it is
recommended that a qualified electrical installer determine that the ground path is adequate.
A copy of the above code standards can be obtained from:
National Fire Protection Association
One Batterymarch Park
Quincy, MA 02269
CSA International
8501 East Pleasant Valley Road
Cleveland, Ohio 44131-5575
A 120 volt, 60 Hz, AC only, 15-amp, fused electrical circuit is required. A time-delay fuse or circuit breaker is also
recommended. It is recommended that a separate circuit serving only this cooktop be provided.
Electronic ignition systems operate within wide voltage limits, but proper grounding and polarity are necessary. Check that
the outlet provides 120-volt power and is correctly grounded.
The wiring diagrams are provided with this cooktop. See "Wiring Diagrams" section.
.,upp I/Reo sn ,menh
Explosion Hazard
Use a new CSA International approved gas supply line.
install a shut-off valve. Securely tighten all gas connections.
if connected to LP, have a qualified person make sure
gas pressure does not exceed 14" (36 cm) water column.
Examples of a qualified person include: licensed heating personnel,
authorized gas company personnel, and authorized service personnel,
Failure to do so can result in death, explosion, or fire.
Observe all governing codes and ordinances. IMPORTANT: This installation must conform with all local codes
and ordinances. In the absence of local codes, installation must conform with American National Standard, National Fuel Gas
Code ANSI Z223.1 - latest edition or CAN/CGA B149 - latest edition.
IMPORTANT: Leak testing of the cooktop must be conducted according to the manufacturer's instructions.
Type of Gas
Natural Gas:
This cooktop is design-certified by CSA International for use with Natural gas or, after proper conversion, for use with LP gas.
This cooktop is factory set for use with Natural gas. To convert to LP gas, see the Gas Conversion instructions
provided in the literature package. The model/serial rating plate located on the underside of the cooktop base has
information on the types of gas that can be used. If the types of gas listed do not include the type of gas available, check
with the local gas supplier.
LP Gas conversion: Conversion must be done by a qualified service technician.
No attempt shall be made to convert the cooktop from the gas specified on the model/serial rating plate for use with a different
gas without consulting the serving gas supplier. See the Gas Conversion instructions provided in the literature package.
Gas Supply Line
Provide a gas supply line of 3/4"(1.9 cm) rigid pipe to the cooktop location. A smaller size pipe on longer runs may result in insufficient gas supply. Pipe-joint compounds that resist the action of LP gas must be used. Do not use TEFLON _t tape. With LP gas, piping or tubing size can be r/2" minimum. Usually, LP gas suppliers determine the size and materials used in the system.
1-®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.
Flexible metal appliance connector:
If local codes permit, use a 1/2"or %" I.D. flexible stainless steel tubing gas connector, designed by CSA to connect the cooktop to the rigid gas supply line.
A 1/2"male pipe thread is needed for connection to the female pipe threads of the inlet to the cooktop pressure
regulator.
Do not kink or damage the flexible metal tubing when moving the cooktop.
Rigid pipe connection:
The rigid pipe connection requires a combination of pipe fittings to obtain an in-line connection to the cooktop. The
rigid pipe must be level with the cooktop connection. All strains must be removed from the supply and fuel lines so
cooktop will be level and in line.
Gas Pressure Regulator
The gas pressure regulator supplied with this cooktop must be used. The inlet pressure to the regulator should be as follows for proper operation:
Natural Gas:
Minimum pressure: 5" (12.7 cm) WCP Maximum pressure: 7" to 14" (17.8 cm to 35.5 cm) WCP
LP Gas:
Minimum pressure: 11" (27.9 cm) WCP Maximum pressure: 14" (35.5 cm) WCP Contact local gas supplier if you are not sure about the inlet
pressure.
Burner Input Requirements
Input ratings shown on the model/serial rating plate are for elevations up to 2,000 ft (609.6 m).
For elevations above 2,000 ft (609.6 m), ratings are reduced at a rate of 4% for each 1,000 ft (304.8 m) above sea level (not
applicable for Canada).
Must include a shutoff valve: The supply line must be equipped with a manual shutoff
valve. This valve should be located in the same room but external to the cooktop. It should be in a location that allows ease of opening and closing. Do not block access to shutoff
valve. The valve is for turning on or shutting off gas to the cooktop.
B
A. Gas supply line B. Shutoff valve "open" position
C. To cooktop
INSTALLATIONINSTRUCTIONS
Excessive Weight Hazard
Use two or more people to move and install cooktop. Failure to do so can result in back or other injury.
Gas Supply Pressure Testing
Line pressure testing above 1/2psi gauge (14" WCP)
The cooktop and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2psi (3.5 kPa).
Line pressure testing at 1/2psi gauge (14" WCP) or lower The cooktop must be isolated from the gas supply piping system
by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to
or less than 1/2psi (3.5 kPa).
2.
Remove foam strip from literature package. Remove backing from foam strip. Apply foam strip adhesive-side down around bottom of cooktop, flush with edge.
NOTE: The foam strip protects the underside of the cooktop glass from debris and helps the cooktop sit flat on uneven
counters.
Decide on the final location for the cooktop. Avoid drilling into or severing existing wiring during installation.
On Glass Cooktop models only:
1. Using 2 or more people, place the cooktop upside down on a covered surface.
A. Cooktop base B. Foam strip C. Cooktop
Style 1: Cooktop over undercounter built-in oven IMPORTANT: Clamping brackets should not be used.
1. Using 2 or more people, place cooktop right side up into the
cutout, NOTE: Make sure that the front edge of the cooktop is
parallel to the front edge of the countertop. If repositioning is needed, lift entire cooktop up from cutout to avoid scratching the countertop.
Style 2: Cooktop over cabinets
1. Determine whether your cabinet construction provides clearance for installing clamping brackets at cooktop base ends. This is the recommended location. Clamping brackets can be installed on the front and back of cooktop base bottom, if necessary.
A.Attachment screw holes for optional front and back
location.
B. Clamping bracket (endlocations recommended) C. Cooktop base bottom
D.Attachment screw
E.Attachment screw location (recommended)
2. The clamping brackets can be installed before or after the cooktop is placed into the cutout. Complete the following steps for the option you choose.
4. Attach brackets to cooktop base bottom with bracket attachment screws using the bracket mounting holes selected in Step 2.
5. Rotate brackets so they do not extend beyond edge of cooktop base.
6. Tighten screws just enough to hold brackets in place when cooktop is put in cutout.
7. Using 2 or more people, turn the cooktop right side up and place in cutout.
NOTE: Make sure that the front edge of the cooktop is parallel to the front edge of the countertop. If repositioning is needed, lift entire cooktop up from cutout to avoid scratching the countertop.
8=
Loosen the screws and rotate the brackets so that they are perpendicular to the edge of the cooktop base and extend beyond its edge. Securely tighten screws.
Installing Brackets After Placing Cooktop in Cutout
Using 2 or more people, place cooktop right side up into the cutout.
NOTE: Make sure that the front edge of the cooktop is parallel to the front edge of the countertop. If repositioning is needed, lift entire cooktop up from cutout to avoid scratching the countertop.
2=
Remove the attachment screws for the selected bracket locations from the bottom of the cooktop base.
3.
Select bracket mounting holes that will allow the bracket to extend far enough out from the cooktop for the installation of 21/2'' (6.4 cm) clamping screws.
G
A
Installing Brackets Before Placing Cooktop in Cutout
1. Using 2 or more people, place the cooktop upside down on a
covered surface.
2. Remove the attachment screws for the selected bracket locations from the bottom of the cooktop base.
3. Select bracket mounting holes that will allow the bracket to extend far enough out from the cooktop for the installation of 21/2'' (6.4 cm) clamping screws. See "Attach Cooktop to Countertop" for illustration of clamping screw installation.
i
I
I
J
A
A. Edge of cooktop base bottom B. Clamping bracket
A. Cooktop B. Cooktop base
C. Attachment screw D. Clamping bracket (extends far enough beyond
cooktop base to allow installation of clamping
screws)
E.2V2" (6.4 cm) clamping screw (to be installed in
"Attach Ceektep to Countertop")
E Countertop
G. Foam seal
4.
Attach brackets to cooktop base bottom with bracket attachment screws using the bracket mounting holes selected in Step 3. Securely tighten screws.
Loading...
+ 14 hidden pages