Whirlpool GLT3014GB, GLT3014GQ, GLT3014GT, GLT3014GZ, GLT3034LB Dimension Guide

...

15" 13-3/4" 19" 15" 2-1/8" 2-7/8" 5-5/8"
(38.1 cm) (34.9 cm) (48.3 cm) (38.1 cm) (5.4 cm) (7.3 cm) (14.3 cm)
30" 29" 19" 30" 2-1/8" 2-7/8" 5-5/8"
(76.2 cm) (73.7 cm) (48.3 cm) (76.2 cm) (5.4 cm) (7.3 cm) (14.3 cm)
36" 35-1/4" 19" 36" 2-1/8" 2-7/8" 5-5/8"
(91.4 cm) (89.5 cm) (48.3 cm) (91.4 cm) (5.4 cm) (7.3 cm) (14.3 cm)
42" 42-3/4" 19" 42" 2-1/8" 2-7/8" 11-1/2"
(106.7 cm) (108.6 cm) (48.3 cm) (106.7 cm) (5.4 cm) (7.3 cm) (28.4 cm)
Gas Built-in Cooktop
PRODUCT MODEL NUMBERS OVERALL DIMENSIONS
GLT3014G GLT3034L GLT3614G GLT3615G GLT3615L GLT3634L
SCS3004G SCS3004L SCS3014G SCS3014L SCS3614G SCS3614L
Gas supply: Cooktop is equipped for use with NATURAL gas (except model KGCR055 - L.P. gas only). Cooktop can be converted to L.P. gas. Gas supply line of 3/4" rigid pipe to cooktop location. If local codes permit, a new AGA or CSA design­certified, 4-5 foot (1.2-1.5 m) long, 1/2" or 3/4" I.D., flexible metal appliance connector is recommended for connecting cooktop to gas supply line. Pressure regulator has 3/8" female pipe threads. The supply line shall be equipped with an approved shutoff valve.
Electrical: 120-volt, 60-Hz, AC-only, 15-amp. electrical supply. Use copper wire only. A time­delay fuse or circuit breaker and separate circuit is recommended.
Grommet is required for electrical cable or power supply cord hole cut in a metal cabinet.
Minimum distance
to combustible
surface above
countertop
Cooktop width
Gounded outlet – Locate within 24" (61 cm) of right rear corner of cutout.
Gas line opening – Wall: anywhere 5" (12.7 cm) below underside of countertop. Cabinet floor: anywhere within 6" (15.2 cm) of rear wall is recommended.
Do not seal cooktop to countertop.
24" (61 cm) min. – deep countertop is required.
min.
13" (33 cm) recommended upper cabinet depth
See NOTE* for minimum clearances.
combustible area above countertop
*
Note: 24" (61 cm) min. clearance if bottom of wood or metal cabinet is protected by not less than 1/4" (0.6 cm) flame retardant millboard covered with not less than No. 28 MSG sheet steel, 0.015" (0.04 cm) stainless steel, or 0.024" (0.06 cm) aluminum or 0.020" (0.05 cm) copper.
30" (76.2 cm) min. clearance between top of cooking platform and bottom of unprotected wood or metal cabinet.
18" (45.7 cm) min. clearance upper cabinet to countertop within minimum clearances to cooktop
Illustration dimensions
Important note on base cabinet construction: After making the countertop cutout, some installations may require notching down the base cabinet side walls to clear the burner box. To avoid this modification, use a base cabinet having sidewalls wider the cutout.
30" (76.2 cm)
36" (91.4 cm)
30"
(76.2 cm)
21"
(53.3 cm)
2-7/8"
(7.3 cm)
2-7/8"
(7.3 cm)
36"
(91.4 cm)
21"
(53.3 cm)
®
Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation Instructions packed with product. Specifications subject to change without notice.
Ref. 4455834 Rev. A
05-12-04
Loading...