Whirlpool RS675PXGT12, RS675PXGT8, RS675PXGT10, RS675PXGQ12, RS675PXGB8 Installation Guide

Quick Reference

Table of Contents:

Pages

[_ Product dimensions

Cabinet opening dimensions

[_ Before you start
j_ Electrical requirements
[_ Installation steps

If you need assistance:

Checkyour Use and Care Guide for a toHofree number to call or call

the dealer from whom you purchased this appUiance.ThedeaUeris

listed in the Yellow Pages of your phone directory under
"Appliances -- Household -- Major -- Service and Repair:'

Call when you:
[_ Have questions about range installation or operation.

[_ Need to obtain the name and number of an authorized service

company.

When you ca[[, you w[[[ need:

The range mode[ number:

[_ The range serial number:
Both numbers are listed on the model/serial rating plate, located on

the oven door or on the oven frame.

28=3/16"
cooktop

recessed width

__ 28=5/32" oven

30=3/4"

recessed

height

from

underside

of cooktop

to support

slats

recessed width

31-1/2"

cooktop

overaU

width

Yearsafetyand thesafetyofothersareveryimportant.

We haveprovided manyimportant safety messagesin this

24=13/32"

to back

manuaiand on your appliance.Always readand obey a[[

safety messages.

This isthe safety alert symbol
This symboi aierts you to potential hazardsthat can

kilI or hurt you and others.

Atisafety messageswiii foiiow the safetyatert symboi and
eitherthe word "DANGER"or "WARNING".Thesewords mean:

31=11/16"

overaU

height

J

You can be killedorseriouslyinjuredifyoudon'tfollow

instructions.

AII safety'messageswilI telI you what the p0tentiaihazardis,
tell you how to reducethe chance of h_jury,and tell you what
can happen if the instructions are not followed.

Countertop preparation:

Front edges:You may need to
shave or cut the trim of formed

or metal front-edged
countertops to dear the 30"

width of cooktop.

13" max. upper

For minimum

clearances to the

top of cooktop see

Note, _

wail

--7

25"countertop

floor

depth
24"lower

cabinet depth

\

cabinet
front

[

Side view of
cabinet cutout

*Note: 24" rain. when bottom of wood or

metal cabinet is protected by not less than

1/4" frame retardant miUboard covered
with not less than No. 28 MSG sheet steel
0,015" stainless steel &024" aluminum or

0.020" copper.

30" rain, clearance between the top of the
cooking platform and the bottom of an

unprotected wood or metal cabinet.

shipping

1=1/8"

max=

foot

if countertop thickness is
more than 1ol/2" inches

thick: Countertop must be

notched as shown to avoid

damaging the oven control

panel.

notch width _ /

to be equal _//

fi_ 1-1"1/2"

30=1/8"

Top of countertop
Note: countertop

must be [eve[
across front and

front to back.

%112" max.
countertop__

thickness

_----- 28=1/2" rain,

[f countertop extends more
1ol/8" beyond cabinet front:

Notch countertop as shown

to dear oven control pane[.

notch width

to be equal

both sides

Top view of
cabinet cutout

114"
radius both

corners

InstaU a 3=l/2"owide
support s_at on each

side, S_ats must be [eve[
front to back and with
each other.

opening width

recommended,

f ave ab e.

cabinet

front

30-3/4"

top of
countertop to
support slats

important: Observe all governing codes and
ordinances.

Proper installation is your responsibility. Have a qualified

technician instal[ this range.

Range location should be away from strong draft areas,
such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used.
Given dimensions provide minimum clearance.

Recessed installation area must provide complete enclosure
around the recessed portion of the range.

Electrical ground is required. See "Electrical requirements"
IMPORTANT.'Some cabinet and building materials are not

designed to withstand the heat produced by the oven for
baking and self-cleaning. Check with your builder or cabinet
supplier to make sure that the materials used wii[ not
discolor, delaminate or sustain other damage.

Range support surface MUST be solid, [eve[ and flush with
bottom of cabinet cutout.

Do not seal range to side cabinets.
When installing a cooktop under existing cabinets and the

installation does not meet the minimum cabinet clearances.
Install a range hood above the cooktop to avoid burn

hazards.

it is the customer's responsibility:

Tocontact a qualified electrical installer.
Toassure that the electrical installation is adequate and in

conformance with National Electrical Code,ANS[/NFPA
70 -- latest edition_% and air local codes and ordinances.

Mobile home installation

The installation of this range must conform to the
Manufactured Home Construction and Safety Standards,
Title 24 CFR, Part 3280 (formerly the Federal Standard for
Mobile Home Construction and Safety, Title 24, HUD, Part

280); or when such standard is not applicable, the Standard
for Manufactured Homes Installations (Manufactured Home

Sites, Communities and Setups), ANSI A225.1/NFPA 501A,
or with local codes._

When this range is installed in mobile home, it must be
secured to the floor during transit. Any method of securing
the range is adequate as long as it conforms to the

standards listed above.
Four-wire power supply cane must be used in a mobile

home installation.The appliance wiring wiii need to be
revised. See four-wire electNcal connection, Page 3.

Tools needed:

Pds

river

Parts supplied:

_2 screws

Copies of the standards listed may be obtained from:
*_ National Fire Protection Association

8atterymarch Park
Quincy, Massachusetts 02269

Page 1

Locate electrical
supply junction

box on cutout
floor or on rear

waU (shown)
near floor line.

7/8" rain.

cutout and

cabinet door

Front view of

cabinet cutout

required

between

or hinge.

l

30=3/4"

top of 36" overaU

counter =

top to height

bottom

cuto;t

of cabinet l

countertop