Whirlpool RS610PXGW0, RS610PXGV2, RS610PXGW3, RS610PXGW7, RS675PXGQ6 Installation Instructions Manual

Quick Reference

Table of Contents:

Pages

[] Product dimensions
[] Cabinet opening dimensions
[] Before you start
[] Electrical requirements

[] [] installation steps

if you need assistance:

Check your Use and Care Guide for a toll-free number to call or call
the dealer from whom you purchased this appliance. The deaHeris
listed ir_the Yellow Pages of your phone directory under

"Appliar_ces -- Household -- Major -- Service and Repair."
CaJJwhen you:
[_ Have questions about range instalration or operation.

[_ Need to obtain the name and number of an authorized service

company.

When you call, you will need:
[] The range model number:

[] The range serial number:

Both numbers are listed on the model/seria} ratir_g plate, located on
the oven door or on the oven frame.

28-3/16"
cooktop

recessed width

__ 28-5/32" oven

recessed width

24-13/32"

to back

30-3/4"

recessed

height

from

underside
of cooktop
to support

slats

31-1/2"
overall

cooktop

width

shipping

foot

23-1/8"

recessed_

depth "_

30"

overall

width

31-11/16"

overall
height

r
J

Countertop preparation:

Front edges: You may need to
shaveor cut the trim of formed

or metal front-edged

countertops to clear the 30"
width of cooktop.

If countertop thickness is
more than 1-1/2" inches
thick: Countertop must be

notched as shown to avoid
damaging the oven control
panel.

notch width _ _._
to be equal /_J_j

_'_ I--1-1/2"

_ _'_ _ max

30-1/8"

If countertop extends more
1-1/8" beyond cabinet front:

Notch countertop as shown
to clear oven control panel.

notch width
to be equal

both sides

cabinet

front

wall

floor

\

13" max. upper

t

For minimum

clearances to the
top of cooktop see

Note.*

--r

- 19-5/8" -_

25" countertop
depth
24" lower
cabinet depth

r

Side view of
cabinet cutout

_1_1-1/8"

max.

X

cabinet
front

*Note: 24" min. when bottom of wood or

metal cabinet is protected by not less than
1/4" flame retardant millboard covered
with not less than No. 28 MSG sheet steel,

0.015" stainless steel, 0.024" aluminum or

0.020" copper,
30" rain. clearance between the top of the

cooking platform and the bottom of an
unprotected wood or metal cabinet.

Page 1

Copies of the standards listed may be obtained from:
** National Fire Protection Association

Batter/march Park
Quincy, Massachusetts 02269

1-1/2" max.

thickness

Top view of
cabinet cutout

1/4"

radius both

corners

30-3/4"

top of
countertop to
support slats

Install a 3-1/2"-wide
support slat on each

side, Slats must be level
front to back and with
each other.

Top of countertop _28-1/2" min.
Note: countertop I opening width
must be level / 28-5/8"
across front and / _ is

front to back. I recommended.

_/ if available.

Locate electrical
supply junction

box on cutout
floor or on rear
wall (shown)
near floor line.

7/8" min.

required

between

cutout and

cabinet door

or hinge.

13

Front view of
cabinet cutout

==+t

30-3/4"
top of 36" overall

counter-

countertop

top to height

bottom

of cabinet _

cutout

Your safety and the safety of others is very
important.

We have provided many important safety messagesinthis
manualandonyour appliance. Always readandobeyall

safety messages.

_J his isthe safety aiert symbol

This symboi alerts you to hazards that can kili or

hurt you and others. Aii safety messageswili be
precededby the safety aiert symboi and the word "DANGER"
or "WARNING"=Thesewords mean:

YouwiJ bekilled or
seriouslyinjuredif you

don'tfollow instructions.
Youcaj bekilled or

seriously injured if you
don't follow instructions.

All safety messages will identify the hazard,tell you howto
reducethe chance of injury, and tell you what can happen if
the instructions are not followed.

Important: Observe all governing codes and
ordinances.

Proper installation is your responsibility. Have a qualified

technician install this range.
Range location should be away from strong draft areas,

such as windows, doors and strong heating vents.
Cabinet opening dimensions that are shown must be used.

Given dimensions provide minimum clearance.
Recessedinstallation area must provide complete

enclosure around the recessed portion of the range.
Electrical ground is required. See "Electrical requirements."
IMPORTANT: Some cabinet and building materials are not

designed to withstand the heat produced by the oven for
baking and self-cleaning. Check with your builder or cabinet
supplier to make sure that the materials used will not
discolor, delaminate or sustain other damage.

Range support surface MUST be solid, level and flush with
bottom of cabinet cutout.

Do not seal range to side cabinets.
When installing a cooktop under existing cabinets and the

installation does not meet the minimum cabinet clearances.
Install a range hood above the cooktop to avoid burn

hazards.
It is the customer's responsibility:

Tocontact a qualified electrical installer.
To assurethat the electrical installation is adequate and in

conformancewith National Electrical Code, ANSI/NFPA
70 -- latest edition**, and all localcodesand ordinances.

Mobile home installation

The installation of this range must conform to the
Manufactured Home Construction and Safety Standards,
l]tle 24 CFR, Part 3280 (formerly the Federal Standard for
Mobile Home Construction and Safety, l]tle 24, HUD, Part

280); or when such standard is not applicable, the Standard
for Manufactured Homes Installations (Manufactured Home

Sites, Communities and Setups), ANSI A225.1/NFPA 501A,
or with local codes.**

When this range isinstalled in mobile home, it must be
secured to the floor during transit. Any method of securing
the range is adequate as long as it conforms to the
standards listed above.

Four-wire power supply cable must be used in a mobile
home installation. The appliance wiring will need to be
revised. See four-wire electrical connection, Page 3.

Toolsneeded:

2" alia,

uter bit

s

river

Parts supplied:

screws 2 door removal pins