Whirlpool RHH5336 Installation Instructions

INSTALLATION

and OPERATING INSTRUCTIONS

for

~irlpool

VENTED RANGE HOOD

TO INSTALL RANGE HOOD

INSTALLING DUCT WORK:
Figure 1 shows typical installation. The unit vents vertically only

with 3% X 10 duct.
Use figure 2 to cut duct hole and wiring entrance hole in furr

down. Note control side for hood on fig. 2; be sure this is the
same side as the cook top controls.

Installation under kitchen furr down:

1.

For easy installation hood should be disassembled. See fig.

4. First remove aluminum filter from fan box assembly by
pulling tab toward opposite end of filter. Then remove blower
assembly by unpluging blower power leads and pushing
retaining brackets off retaining bumps. Finally, remove black
fan box assembly by removing 6 screws. (See fig. 4). Remove

hood mounting brackets from interior shipping position.

2. Depending on mounting surface, use either prepunched
holes in the hood flanges at the top or the mounting brackets
included with the hood to secure the hood to the furr down. If
mounting brackets are used, screw the brackets to the furr
down six to nine inches from the hood ends. Use the center hole

to mount the bracket initially. Leave the center screw loose
enough to rotate on the center screw. Rotate the brackets as
shown in Fig. 3, and lift the hood canopy (without black fan box

assy.) into position. Rotate brackets until they are supporting

the hood canopy. Attach remaining screws.

3.

Make electrical connection in wiring box according to the
latest National Electrical Code and applicable local codes.
Hood must be permanently grounded.

4. Lift fan box assembly into position and make necessary
ductwork connections. Secure fan box assembly to hood
canopy with six screws.

5. Replace blower 8 filter.

FIG.

RHH5336

1

I

t-t

FIG. 3

VIEW LOOKING

FIG. 2

UP AT FURR DOWN

6”

TO 9”

VIEW LOOKING UP
AT FURR DOWN

f

\CONTROL SIDE

6/B

c, ,v

t

II

NOTE: It has been found that a large part of theenergy loss of

CORPORATION

the average home is due to outside air infiltrating the structure.
Seal around ductwork where it passes through outside walls or
ceiling. Seal around electrical wiring also.

DAMPER BLADE

MTG

‘TAPED TO

ARE

FAN

MTG. BRACKET
SCREWS(6)

BRACKETS

BOX ASSY

FAN BOX

ASSY.

I

/ I

c:

FIG. 5

OPERATION AND CARE OF

BLOWER CONTROL
This range hood has a solid state motor speed control. This

allows an infinite control of blower air moving capacity from 370

CFM down. After setting the control to a desired speed, it will
take approx. 15 seconds for the blower to respond to that
setting.

CARE OF BLOWER

Under normal operating conditions, this blower requires no

oiling for the first year. After the first year oil every 6 months
with SAE 20 oil.

USE NO LAMP LARGER THAN 75 WATT: Hood is designed
for 75 watt flood lamp for greater illumination and bulb life.

Whirlpool franchised TECH-CARE- service

If your WHIRLPOOL appliance ever needs servlceanywhere
in the UnIted Slates. help is just a phone call away. .to your
nearest TECH-CARE service representative.

WhIrlpool maintains a nationwide network of franchised

TECH-CARE service companies to fulfill your warranty and

provide after-warranty service and maintenance to keep your

WHIRLPOOL appliance In peak condition.

You’ll find your nearest TECH-CARE servlcecompany listed
In your local telephone book Yellow Pages under

Washers/Dryers-Repairing or Servicing. Should you not find a

listing, dial free, the WhIrlpool COOL-LINE@ service assistance
telephone number [phone] When calling from-

Michigan Dial [phone]

Alaska& Hawall.. Dial [phone]

II you move..

Call the TECH-CARE service representative In your local
area He’ll see to the lnstallatlon of WHIRL.POOL appliances in
your new home, promptly, expertly and fairly priced to you.

Helpful hints.

You can help your TECH-CARE service representative give
you faster service If you Include the model and serial number of
your appliance when requesting service. Also, retain your sales
slop and warranty to verify your warranty status.

Remember..

Your TECH-CARE service representative IS specially trained
In the expert repaIrIng and servlclng of your WHIRLPOOL
appliances. He can help you malntam the quality origInally built
into your
to look up his telephone number and jot it down In the space

provided below.

WHIRLPOOL

appliance

So

why not takethe time, now,

I

I_
FAN BOX MTG.
SCREWS (6)

ALUMINUM
FILTER

FIG. 4

UNIT

CARE OF FILTER

For greatest efficiency, the permanent aluminum filter should
be removed and cleaned periodically. The filter can be washed
in a dishwasher.

CARE OF EXTERIOR SURFACES
Your range hood is a beautifully finished addition to your

kitchen. To preserve its lasting beauty, clean with a mild
detergent. DO NOT use abrasive cleaners.

My TECH-CARE service representative’s telephone number

Range hood model number:

Range hood serial number:

Purchase and/or Installation date:

IS:

TLirlpool

Benton Harbor, Mlchlgan Automatic Washers,
Clothes Dryers, Freezers, Refrigerator-Freezers,
Ice Makers, DIshwashers, Bu~ll-tn Ovens and
Surface Units. Ranges, MIcrowave Ovens. Food
Waste Disposers, Compactors, Room Air
Condltloners. Dehumidihers, Central Healing and
Air Conditlonlng Systems

PIN 030729 A625-034