Whirlpool RCS3004RS05, RCS3014RT04, RCS3014RB05, RCS3014RS04, RCS2012RS06 Installation Instructions Manual

...

0 (0)

ELECTRIC BUILT-IN COOKTOPS

21" (53.3CM), 30" (76.2CM), AND 36" (91.4CM)

INSTALLATION INSTRUCTIONS

INSTRUCTIONS D'INSTALLATION DE

LA TABLE DE CUlSSON I_LECTRIQUE ENCASTRf--EDE

21" (53,3CM), 30" (76,2CM), ET 36" (91,4CM)

TableofContents/Tabledes mati@res

BUILT-IN COOKTOP SAFETY ........................ 2

INSTALLATION INSTRUCTIONS .................... 3

Tools and Parts ............................................. 3

Location Requirements ................................. 3

Electrical Requirements ................................ 4

Install Cooktop .............................................. 5

Make Electrical Connection .......................... 7

Complete Installation .................................... 8

SI_CURITE DE LA TABLE

DE CUISSON ENCASTRI_ ............................... 9

INSTRUCTIONS D'INSTALLATION .............. 10

Outillage et pieces ....................................... 10

Exigences d'emplacement .......................... 10

Specifications _lectriques ........................... 11

Installation de la table de cuisson ............... 13

Raccordement _lectrique ............................ 14

Achever I'installation ................................... 16

IMPORTANT: Installer: Leave installation instructions with the homeowner.

Homeowner: Keep installation instructions for future reference.

Save installation instructions for local electrical inspector's use.

IMPORTANT : Installateur : Remettre les instructions d'installation au proprietaire. Propri_taire : Conserver les instructions d'installation pour reference ulterieure.

Conserver les instructions d'installation pour consultation par I'inspecteur local des installations electriques.

8286310

BUILT-INCOOKTOP SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

INSTALLATIONINSTRUCTIONS

Gather the required tools and parts before starting installation.

Tools needed

• Tape measure • Marker or pencil

• Flat-blade screwdriver • Pliers

Parts supplied

• Clamp brackets (2)

• 21/2"(6.4 cm) clamping screws (2) Parts needed

• A UL listed or CSA approved conduit connector

• ULlisted wire nuts Check local codes. Check existing electrical supply. See

"Electrical Requirements."

All electrical connections should be made by a licensed, qualified

electrical installer.

Make sure you have everything needed for correct installation. It is the responsibility of the installer to comply with the installation clearances specified in these instructions.

IMPORTANT: Observe all governing codes and ordinances. When installing cooktop, use minimum dimensions given.

• To eliminate the risk of burns or fire by reaching over the heated surface units, cabinet storage space located above the surface units should be avoided. If cabinet storage is to be

provided, the risk can be reduced by installing a range hood that projects horizontally a minimum of 5" (12.7 cm) beyond

the bottom of the cabinets.

• The cooktop must be a specified cooktop that is approved to be installed either alone or over an undercounter built-in oven.

Check the cooktop burner box for an approved installation label. If you do not find this label, contact your dealer to confirm that your cooktop is approved.

• Ovens approved for this type of installation will have an approval label located on the top of the oven. If you do not find this label, contact your dealer to confirm that your oven is approved. Refer to oven manufacturer's Installation

Instructions for approval for built-in undercounter use and proper cutout dimensions.

• When installing cooktop over an undercounter built-in oven, do not fasten cooktop to countertop with clamps. This will

make the cooktop easier to remove if future servicing becomes necessary.

• The cooktop should be installed away from strong draft areas, such as windows, doors, fans or strong heating vents. The

cooktop should be located for convenient use in the kitchen.

• Use the countertop opening dimensions that are given with these Installation Instructions. Given dimensions are minimum

clearances and provide 0" (0 cm) clearance.

• Grounded electrical supply is required. See "Electrical Requirements" section.

Product Dimensions

A. 21" (53.3 crn) B. 30" (76.2 cm)

36" (91.4 cm) C. %d' (1.g cm) O. 27/8"(7.3 cm)

A. 16V2"(41.9 cm) B. 21" (53.3 cm) C. 18" (47.7cm) overall O. 2%" (7.3 cm)

Installation Clearances

For 21" (53.3 cm) model only:

back edge

rear of cabinet or of cutout rear wall under

countertop

A. 21" (53.3 cm) on 21" (53.3 cm) models; 30" (76.2 cm) models on

30" (76.2 cm) models; 36" (91.4 cm) on 36" (91.4 cm) models B. Combustible area above countertop (shown by dashed box above) C. 30" (76.2 cm) minimum clearance between top of cooktop platform

and bottom of unprotected wood or metal cabinet (24" [61 cm]

minimum clearance if bottom of wood or me tal cabinet is protected

by not less than V4"[0.6 cm] flame retardant millboard covered with

not less than No. 28 MSG sheet steel, 0.015" [0.04 cm] stainless

steel or 0.024" [0.06 cm] aluminum or 0.020" [0.05 cm] copper) D. 13" (33 cm) recommended upper cabinet depth E. 3" (7.6 cm)

F. 15V2"(34.4 cm) on 21" (53.3 cm) models; 18%" (45.7 cm) on

30" (76.2 cm) models and36" (91.4 cm) models G. 18" (45.7 cm) minimum clearance from upper cabinet to

countertop within minimum horizontal clearances to cooktop H. Junction box or outlet," 12" (30.5 cm) minimum from bottom of

countertop; 10" (25.4 cm) from right side of cabinet

I. 18%" (33.7 cm) on 21" (53.3 cm) models; 287/8'' (47.3 cm) on

30" (76.2 cm) models; 35" (90.2 cm) on 36" (91.4 cm) models

J. 1" (2.5 cm) minimum distance to nearest left and right side

combustible surface above cooktop K. 1%G"(3.4 cm) max. counter thickness on 21" (53.3 cm) models. See

following illustration.

L. 1" (2.5 cm) minimum clearance between back waft and countertop

NOTES: After making the countertop cutout, some installations may require notching down the base cabinet side walls to clear

the burner box. To avoid this modification, use a base cabinet with

sidewalls wider than the cutout. If cabinet has a drawer, a3" (7.6 cm) depth clearance from the

countertop to the top of the drawer (or other obstruction) in base cabinet is required.

When installing a hood above this cooktop, follow the installation instructions included with the hood itself.

A. WI_" (1.7cm) min. B. !5/16"(3.4 cm) max.

240 volt Cooktop:

Electrical Shock Hazard Disconnect power before servicing. Use 8 gauge copper wire. Electrically ground cooktop.

Failure to follow these instructions can result in death,

fire, or electrical shock.

If codes permit and a separate ground wire is used, it is recommended that a qualified electrical installer determine that

the ground path and wire gauge are in accordance with local codes.

Do not ground to a gas pipe. Check with a qualified electrical installer if you are not sure the

cooktop is properly grounded. Do not have a fuse in the neutral or ground circuit.

Make sure that the electrical connection and wire size are adequate and in conformance with the National Electrical Code,

ANSl/NFPA 70-latest edition or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No. O-M91-1atest edition, and all local codes and ordinances.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park

Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

Before You Make the Electrical Connection:

To properly install your cooktop, you must determine the type of

electrical connection you will be using and follow the instructions provided for it here.

• A 4-wire or 3-wire, single phase, 240 volt, 60 Hz., AC only electrical supply is required on a separate, 40-amp circuit,

fused on both sides of the line. NOTE: The 15" (38.1 cm) model series requires a 20-amp

circuit.

• The cooktop should be connected directly to the junction box through flexible, armored or nonmetallic sheathed, copper

cable. The flexible, armored cable extending from the fuse box or circuit breaker box should be connected directly to the

junction box.

• Locate the junction box to allow as much slack as possible between the junction box and the cooktop so that the cooktop

can be moved if servicing becomes necessary in the future.

• Do not cut the conduit. Use the length of conduit provided.

• A UL listed or CSA approved conduit connector must be provided at each end of the power supply cable (at the cooktop and at the junction box). A listed conduit connector is already provided at the cooktop.

• If the house has aluminum wiring, connect the aluminum wiring to the copper wire by using special connectors

designed and UL listed for joining copper to aluminum. Follow the electrical connector manufacturer's recommended

procedure. Aluminum/copper connection must conform with local codes and industry accepted wiring practices.

120 volt Cooktop:

Emectrica_ Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or emectrical shock.

A 120 volt, 60 Hz, AC only, 20-amp fuse, fused electrical supply is required. A time-delay fuse or circuit breaker is recommended. It is recommended that a separate circuit serving only this appliance be provided. A NEMA 5-20R,

3 prong grounding-type outlet must be used.

For your personal safety, this cooktop must be grounded. This cooktop is equipped with a power supply cord having a NEMA

5-20P, 3 prong grounding plug. To minimize possible shock hazard, the cord must be plugged into a mating, NEMA 5-20R, 3 prong grounding-type outlet, grounded in accordance with the National Electrical Code, ANSI/NFPA 70 latest edition, and local codes and ordinances.

• If a mating outlet is not available, it is the personal responsibility and obligation of the customer to have a properly grounded, NEMA 5-20R, 3 prong outlet installed by a

qualified electrician.

WARNING: Improper connection of the equipment grounding conductor can result in a risk of electric shock. Check with a

qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded. Do not modify the

plug provided with the appliance, if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

1. Remove the shipping materials and tape from the cooktop. Remove the hardware package from inside the literature bag.

2. Using 2 or more people, place the cooktop upside down on a protective surface.

A. Attachment screw holes for optional front and back location B. Clamp bracket (end locations recommended)

C. Burner box bottom D. Attachment screw

E.Attachment screw location (recommended)

Two clamp brackets are provided to clamp the cooktop to the countertop. Install the clamp brackets on each end of the burner box bottom. If cabinet construction does not provide clearance for installing brackets at the burner box ends, install the brackets on the front and back of the burner box bottom.

NOTE: For lift top models, the brackets may be installed before or after the cooktop is placed into the cutout. However, installing the brackets after is not recommended for lift top models.

+ 11 hidden pages