WHIRLPOOL GBD309PV, GBS309PV, RBD305PV, RBD307PV, RBS305PV User Manual

...

PRODUCT MODEL SERIES

PRODUCT DIMENSIONS

GBD309PV GBS309PV RBD305PV

RBD307PV RBS305PV RBS307PV

Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice.

Dimensions are for planning purposes only. For complete details, see Installation Instructions packed with product. Specifications subject to change without notice.

Ref. W10192049B

09-05-08

30" (76.2 CM) ELECTRIC SINGLE AND DOUBLE BUILT-IN OVEN

A. 28⁵⁄₁₆" (71.9 cm) max. recessed width B. 29" (73.7 cm) max. overall height C. 29³⁄₄" (75.6 cm) overall width D. 23" (58.4 cm) max. recessed depth E. 27¹⁄₂" (69.9 cm) recessed height

CABINET DIMENSIONS

A. 28⁵⁄₁₆" (71.9 cm) max. recesse d width B. 51" (129.5 cm) max. overall height C. 29³⁄₄" (75.6 cm) overall width D. 23" (58.4 cm) max. recessed depth

E. 49⁹⁄₁₆" (125.9 cm) recessed height

Single Oven

Double Oven

Single Oven Undercounter

(without cooktop installed above)

A. 30" (76.2 cm) min. cabinet width B. 1¹⁄₂" (3.8 cm) min. top of cutout to

underside of countertop C. 5¹⁄₄" (13.3 cm) bottom of cutout to floor D. 28¹⁄₂" (72.4 cm) cutout width E. 27³⁄₄" (70.5 cm) min. cutout height

Single Oven Installed in Cabinet

A. 30" (76.2 cm) min. cabinet width B. 1" (2.5 cm) top of cutout to bottom

of upper cabinet door C. 32" (81.3 cm) bottom o f cutout to floor D. 28¹⁄₂" (72.4 cm) cutout width E. 1¹⁄₂" (3.8 cm) min. bottom of cutout to

top of cabinet door F. 2 7³⁄₄" (70.5 cm) cutout height

tenibaC ni dellatsnI snevO elbuoD

A. 30" (76.2 cm) min. cabinet width B. 1" (2.5 cm) top of cutout to bottom of

upper cabinet door C. 14³⁄₄" (37.5 cm) bottom of cutout to floor D. 28¹⁄₂" (72.4 cm) cutout width E. 1¹⁄₂" (3.8 cm) min. bottom of cutout to

top of cabinet door F. 4 9³⁄₄" (126.4 cm) min. cutout height

nevO elbuoD ro elgniS

- weiV ediS tenibaC

A. 23¹⁄₄" (59.1 cm) min. cutout depth B. 23" (58.4 cm) recessed oven depth C. Oven front D. Recessed oven E. Cabinet

Electrical Requirements: Oven must be connected to the proper electrical voltage and frequency as specified on the model/serial number rating plate. The model/serial number rating plate is located at the bottom of the right-hand mounting rail. See the following illustrations.

Models rated from 7.3 to 9.6 kW at 240 volts (5.5 to 7.2 kW at 208 volts) require a separate 40-amp circuit. Models rated at 7.2 kW and below at 240 volts (5.4 kW and below at 208 volts) require a separate 30-amp circuit.

A circuit breaker is recommended. Connect directly to the circuit breaker box (or fused disconnect) through flexible, armored or nonmetallic, sheathed copper cable (with grounding wire).

Flexible conduit from the oven should be connected directly to the junction box. Do not cut the conduit. The length of conduit provided is for serviceability of the oven. A UL-listed or CSAapproved conduit connector must be provided.

If the house has aluminum wiring, follow the procedure below:

1. Connect a section of solid copper wire to the pigtail leads.

2. Connect the aluminum wiring to the added section of copper wire using special connectors and/or tools designed and UL-listed for joining copper to aluminum.

Follow the electrical connector manufacturer's recommended procedure. Aluminum/copper connection must conform with local codes and industry-accepted wiring practices.

Single Oven

. Model/serial number plate

Double Oven

A. Model/serial number plate

CUTOUT DIMENSIONS FOR OVENS INSTALLED UNDER COOKTOP

IMPORTANT: Observe all governing codes and ordinances. Cooktop must be approved for use over an oven. See Cooktop Installation Instructions for cutout dimensions. Center the cooktop cutout over oven cutout.

To avoid damage to your cabinets, check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate or sustain other damage. This oven has been designed in accordance with UL and CSA International and complies with the maximum allowable wood cabinet temperatures of 194°F (90°C).

Approved Built-In Oven and Electric Cooktop Combinations

A. 24" (61 cm) cabinet depth B. 25" (63.5 cm) countertop depth C. Recommended oven and cooktop junction box locations D. Allow ⁵⁄₈" (1.6 cm) for oven trim to overlap on each side. E. 27¾" (70.5 cm) minimum cutout height

F. 36" (91.4 cm) from cabinet base to countertop

G. 4⁵⁄₈" (11.7 cm) from floor

H. See Cutout Dimensions chart.

CUTOUT DIMENSIONS Oven Size Oven Cutout Dimension

24" (61 cm) 22¹⁄₂" (57.2 cm) 27" (68.6 cm) 25¹⁄₂" (64.8 cm) 30" (76.2 cm) 28½" (72.4 cm) 36" (91.4 cm) 34¹⁄₂" (87.6 cm)

For the approved model number combinations, refer to the undercounter label located on top of the oven chassis and on the bottom of the cooktop burner box.

NOTE: For undercounter installation, it is recommended that the junction boxes for oven and cooktop be located in the adjacent right or

left cabinet. A 1" (2.5 cm) minimum diameter hole should have been drilled in the upper rear right or left corner of the side wall surface to pass the appliance cable through to the junction box. On models with Steam-Assist, it will be necessary to drill a ½" (1.3 cm) minimum diameter hole in the upper right or left rear corner of the side wall to pass the water supply tubing through to the undersink water filter. If water supply tubing hole is drilled on the same side as the oven cable hole, a minimum of 2" (5.1 cm) is required between the 2 holes.

W10373101A

Approved Built-In Oven and Induction Cooktop Combinations

F. 36" (91.4 cm) from cabinet base to countertop

G. 3⁵⁄₈" (9.2 cm) from floor

H. See Cutout Dimensions chart.

CUTOUT DIMENSIONS Oven Size Oven Cutout Dimension

24" (61 cm) 22¹⁄₂" (57.2 cm) 27" (68.6 cm) 25¹⁄₂" (64.8 cm) 30" (76.2 cm) 28½" (72.4 cm)

For the approved model number combinations, refer to the undercounter label located on top of the oven chassis and on the bottom of the cooktop burner box.

NOTE: For undercounter installation, it is recommended that the junction boxes for oven and cooktop be located in the adjacent right or

left cabinet. A 1" (2.5 cm) minimum diameter hole should have been drilled in the upper rear right or left corner of the side wall surface to pass the appliance cable through to the junction box. On models with Steam-Assist, it will be necessary to drill a 1" (1.3 cm) minimum diameter hole in the upper right or left rear corner of the side wall to pass the water supply tubing through to the undersink water filter. If water supply tubing hole is drilled on the same side as the oven cable hole, a minimum of 2" (5.1 cm) is required between the 2 holes.

+ 6 hidden pages