Whirlpool PRBN 350I A, WBE3322 A NFNF, WBE3322 A NFWF, WBE 3323 NFS, CFS 171 PRODUCT SHEET

A. Refrigerator Compartment

2. Lighting

3. Shelves / Shelf area

4. Multi-flow cold air system

5. Cooler compartment

6. Rating plate with commercial name

8. Crisper divider

9. Reversibility kit

10. Egg tray

11. Separator

12. Door trays

B. Freezer Compartment

13. Storage zones for frozen food items (basket or flap)
13a. “Eco green” basket (only in models with ECO

GREEN function)

14. Shelves

15. Bottom basket (freezing zone)

16. Ice tray and/or cold accumulator

18. The freezer door trays for pizza or other frozen

products with a short storage time

Depending on the model the number and type of
accessories may vary.
The freezer compartment can be used without the
baskets / flap and without upper shelf to increase storage
for large products. Place the food products directly on the
racks. After inserting food, ensure that the freezer
compartment door closes properly.

C. Control panel
Anti-bacterial protection :

1. Filter in fan (depending on the model)

7. Crisper with antibacterial additives (depending
on the model)

17. Door seals

The crisper and the door seals are manufactured from

materials that inhibit bacterial growth.

Notes:

- In case of power failure the cold accumulator helps

to keep optimal storage temperature longer.

- All shelves and door trays are removable.

- The internal temperatures of the appliance depend

on the ambient temperature, frequency of opening the
doors, as well as location of the appliance. Temperature

setting must consider these factors.

- The appliance accessories are not suitable for
washing in dishwasher.

FAN WITH A BUTTON

The fan gives more even temperature distribution inside
the refrigerator compartment, allowing better
preservation of stored food.
To switch on the fan press the button (1a). It is advisable
to activate the fan when the ambient air temperature is
over 27 ÷ 28°C or if you perceive drops of water on the
glass shelves or in the severe humidity conditions.

Note:
Do not obstruct the air intake area with food items.
The fan will run ONLY when the compressor is in
operation. Remember to turn off the fan when
there is a lower ambient air temperature.

If the appliance has the fan it can be equipped with the
antibacterial filter.
Remove it from the box (found in the crisper drawer
(item 7) and insert into the cover of fan (item 1b).
The replacement procedure is attached with the filter.

HOW TO START THE APPLIANCE

Fit the spacers (if supplied) on the
upper part of the condenser at the
rear of the appliance. After plugging

the appliance to the mains, it starts
the operation automatically. Wait at least two hours
before switching the appliance on, to ensure that the
refrigerant circuit is fully efficient. The indicator lamps on
the control panel light up for approximately 1 second, and
after initialization process, setpoint is displayed.

Note:

- If food is placed in the refrigarator before the appliance
has cooled completely, it may deteriorate.

- If fresh food is loaded in freezer position 3 on control
panel should be chosen.

CONTROL PANEL DESCRIPTION

1. extra low temperature

2. low temperature

3. "ECO GREEN" position (depending on the model)

4. high temperature

5. temperature selection pushbutton

6. internal light switch

OPERATION DESCRIPTION

Temperature adjustment is made with pushbutton (5).
Temperature setpoint is done for both compartments at
one time – fridge and freezer.

PRODUCT SHEET

GB

ROBGRUSHSKCZPLIGB FINDKNSGRPENLFD

At first plug-in of appliance factory setpoint is chosen –
medium position (ECO Green, depending on model).
Following table shows set-points level

Description Lamp OFF Lamp ON

GUIDE TO SELECTING FUNCTIONS

Temperature selection pushbutton is used to set

desired temperature level, from warmest through
lower to coldest .
Pressing pushbutton setpoint will change cyclically.

Cooling off /Stand-by function

This function turns off the refrigerator and freezer
compartments.
When the product is in this mode the light operates
normally, all other loads are disabled and control panel
shows no indication. When the appliance has to be left for
a longer period with fridge door open to avoid odour,
power cord has to be unplugged from the power supply.
To put the appliance in this state press and hold
temperature selection pushbutton for 3 seconds.
Appliance comes back to normal operation, control panel
displays previously chosen set-point after press
temperature selection pushbutton again.

Note:

- Remember that this operation does not disconnect the
appliance from the power supply.

- In case of power failure, appliance goes back to normal
operation and previously chosen setpoint is restored.

ECO GREEN function

This function gives best food preservation performance
with the smallest energy consumption possible (around 5­10% less in comparison with the normal settings) if there
is lower amount of food to be preserved in the appliance.
The best food preservation conditions when ECO
function is activated are in the ECO compartments:

- 2 "eco green" shelves in the fridge (with green frames)

- 1 "eco green" basket in freezer compartment.

ABNORMAL APPLIANCE OPERATION

When the product is plugged in to the mains, during first
10 minutes of its performance, possible temperature
sensor failure will be displayed according to following
table:

Description Lamp OFF Lamp Flashing

The appliance will work preserving the food stored, but it
is necessary to contact after-sales service and provide
alarm code.

DEFROSTING THE FREEZER
COMPARTMENT

No Frost freezers provide chilled air circulation around

the storage areas and prevent the formation of ice,
thereby completely eliminating the need for defrosting.
Frozen items don't stick to the walls, labeling stays legible
and storage space remains neat and clear.

DEFROSTING THE REFRIGERATOR
COMPARTMENT

Refrigerator compartment defrosting is completely
automatic.

Droplets of water on the rear wall inside the refrigerator
compartment indicate that the automatic defrost phase is
in progress. The defrost water is automatically run into a
drain hole and collected in a container, where it
evaporates.

REPLACING THE LIGHT BULB

Always disconnect the
refrigerator from the power
supply before replacing any
light bulb.
If the inside light is not
working, it is necessary to:

1. Remove the light cover: put the fingers into the side

ventilation holes (1), stretch the cover gently and
move it upwards.

2. Check the bulb. If necessary unscrew the broken bulb

and replace it with the new one (use maximum 15W
bulb).

3. Put on the light cover.

Do not leave the bulb uncovered.

PRODUCT SHEET

GB

5019 637 01067

Printed in Poland 01/10

ROBGRUSHSKCZPLFINDKNSGRIPENLFGBD

Refrigerator sensor failure

Freezer sensor failure

Refrigerator freezer sensor failure

high temperature

low temperature

extra low temperature