Whirlpool PDSI 6232 X PROGRAM CHART

GB

Before using the dishwasher, read the installation and maintenance instructions carefully!

PDSI 6232

1. OVERVIEW

Detergent setting upon initial use and when using a different type of detergent

1. Select the third programme in the relative table.

Programme selection button

START button
The indicator lights up during operation, flashes when a fault
occurs and goes off at the end of the programme.
START button reset function
Press this button for at least 2 seconds and the started programme
and the extra functions selected are cancelled. Main failure displays
(repeated flashing of the START indicator lamp) can be cancelled
by RESETTING. Detailed instructions are given in chapter 5
“What to do if...”.

Salt level indicator and rinse aid level indicator
These indicator lamps light up when salt or rinse aid need to be added.
Only add just before starting a wash cycle.

Fault indication and wash time display
In normal operation it indicates the remaining time (h:mm),
whereas with “Delayed start” selected it indicates the time
remaining until programme start (hh).
If “F..” – appears on the display, see chapter 5 “What to do if…”.

D

elayed start button
Push the button (repeatedly) to delay the start of the program.
Adjustable from 1 to 24 hours. With each press of the button, the
delayed start indicator increases by one hour and after 24 restarts
from 00. Then press the START button. The wash programme will
start after the set time.

2. Keep the START button pressed for about. 7 sec. to change the display.

3. Using the START button, select the desired detergent:
Display shows: 2 -1 = 2 in 1, 3 -1 = 3 in 1, 4 -1 = other combined action
detergents (in this way, the rinse aid and/or salt indicator is deactivated).
Display shows OFF = Powder detergent (factory setting).
(Rinse aid level and salt level indicator activated).

4. Switch the appliance off and then switch it on again. The selected detergent
type will be indicated on the display for approx. 3 sec.

Antibacterial +
This function activates an antibacterial rinse at the end of the wash
cycle, guaranteeing a further reduction of bacteria. Press the button to
activate or deactivate the function. This function can be used with
those programmes marked with the relative symbol in table 1.1.
The dishwasher door must be kept shut for the entire duration of
the programme in order to guarantee reduction of bacteria. If the
door is opened the indicator lamp starts flashing.

On/Off button

3)

Table 1.1.

Table of programmes

cold

40°C

45°C

50°C

70°C

Available

options

P

1

2

3

4

5

6

1) Programme data obtained in conformity with European standard EN 50242. The data may vary, for example, according to
different loads, extra functions, sensor settings (only with sensor programmes), water supply temperatures, water hardness
and power supply voltage.

2) Programme for energy data label in conformity with EN 50242. - Information for Test Laboratories:
EN/Standard loading comparison test and other tests, contact the following address: “[e-mail]”.

3) The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on. Standard NF EN 13697 ­November 2001.

Programs

Auto

Pre-Rinse

Glasses

Quickwash

Eco

Intensive

50-65°C

2)

Description of programme large small Litres kWh Minutes

Recommended programme for
routine washes, with dried-on food
(e.g. EN 50242).

Crockery to be washed later. — — 4.0 0.03 14 ±

Light soiling, for example glasses
and cups.

Lightly soiled crockery, with no
dried-on food.

Normally soiled crockery.
Energy Saving Programme.

Recommended programme for
heavily soiled crockery, particularly
suitable for pots and pans.

Detergent

dispenser

X X 11-16 1.10-1.50 100-130 ±

X — 10.0 0.85 100 ±

X — 11.0 0.80 30 ±

X X 11.0 1.05 155 ±

X X 14.0 1.55 155 ±

Consumption

for detailed information on the

1)

5019 696 01014

1)

1)

1)

1)

1)

1)

1