Page 1
CONTENTS
3gb20020.fm Page 12 Tuesday, February 24, 2004 4:07 PM
Black process 45.0° 150.0 LPI
BEFORE USING THE APPLIANCE
PRECAUTIONS AND GENERAL
RECOMMENDATIONS
DESCRIPTION OF THE APPLIANCE
FILLING THE DETERGENT AND ADDITIVES
REMOVING THE FILTER
DRAINING RESIDUAL WATER
CARE AND MAINTENANCE
TRANSPORT / HANDLING
INSTALLATION
ELECTRICAL CONNECTION
12
Page 2
BEFORE USING THE APPLIANCE
3gb20020.fm Page 13 Tuesday, February 24, 2004 4:07 PM
Black process 45.0° 150.0 LPI
1.Removing the packaging and inspection
•
After unpacking, make sure that the appliance is
undamaged. If in doubt, do not use the appliance.
Contact After-Sales Service or your local retailer.
•
Keep the packaging materials (plastic bags,
polystyrene parts, etc.) out of reach of children,
as they are potentially dangerous.
2.Remove the transport bolts
•
The appliance is fitted with transport bolts to
prevent internal damage during transport.
Before using the appliance, you must
remove the transport bolts
Remove the transport bolts”).
(see “Installation/
3.Install the appliance
•
Move the appliance without carrying it by the
worktop.
•
Install the appliance on a solid and level floor
surface, preferably in a corner of the room.
•
Make sure that all four feet are stable and resting on
the floor and then check that the appliance is
perfectly level using a spirit level (see Installation/
Adjust the feet”).
4.Water supply
•
Connect the water supply inlet hose in
accordance with the regulations of your local
water company (see “Installation/Connect the
water inlet hose”).
•
Water supply: Cold water only
•
Tap: 3/4” threaded hose
connector.
•
Pressure: 0.05-1.00 MPa
(0.5-10 bar).
5.Drain
•
Connect the drain hose to the siphon or hook it
over the edge of a sink with the “U” bend
(see “Installation/Connect the water drain hose”).
•
If the appliance is connected to a built-in drainage
system, ensure the latter is equipped with a vent
to avoid simultaneous loading and draining of
water (siphoning effect).
6.Electrical connection
•
Electrical connections must be carried out by a
qualified technician in compliance with the
manufacturer’s instructions and current standard
safety regulations.
•
Voltage information, power consumption and
electrical protection data are supplied on the
inside of the filter cover.
•
The appliance must be connected exclusively by
means of a socket with an earth connection in
accordance with current regulations. The
appliance must be earthed by law. The
manufacturer declines all liability for damage to
persons or property deriving directly or
indirectly from failure to observe the directions.
•
Do not use extension leads or multi sockets.
•
Before any maintenance on the appliance
disconnect it from the mains supply.
•
After installation, access to the mains plug or
disconnection from the mains supply must be
ensured at all times via a double-pole switch.
•
Do not operate the appliance if it has been
damaged during transport. Inform the After-Sales
Service.
•
Mains cable replacement is only to be carried out
by After-Sales Service.
•
The appliance must only be used in the
household for the prescribed uses.
13
Page 3
PRECAUTIONS AND GENERAL
3gb20020.fm Page 14 Tuesday, February 24, 2004 4:07 PM
Black process 45.0° 150.0 LPI
RECOMMENDATIONS
1.Packing
•
The packing material is recyclable as indicated by the
recycling symbol . Adhere to local regulations
when disposing of packaging material.
2.Energy saving tips
•
Achieve the best use of energy, water, detergent and
time by using the recommended maximum load size.
•
Do not exceed manufacturers’ recommended
dosages as shown on the detergent package.
•
The Eco Flap - a special system in the outlet - will
prevent detergent loss from the drum to avoid
detergent loss into the environment.
•
Use “Prewash” for heavily soiled laundry only!
Save detergent, time, water and energy
consumption by not selecting “Prewash” for slight
to normally soiled laundry. You save on water,
energy and time as a result.
•
Pretreat stains with stain remover or soak dried in
stains in water before washing to reduce the
necessity of a hot wash program.
•
Save energy by using a 60° C instead of a 90° C
wash programme or a 40° C instead of a 60° C
wash programme.
•
Save energy and time by selecting a high spin
speed to reduce the water content in laundry
before using a drying programme (for appliances
with adjustable spin speed).
3.Disposing of packaging and old
appliances
•
The appliance is built from reusable materials.
Dispose of the appliance in conformity with
environmental regulations.
•
Before scrapping, cut off the power cable so that the
appliance cannot be connected to the mains.
•
Remove detergent from compartment if you
intend scrapping your appliance.
4.Child safety
•
Children must not be allowed to play with the
appliance.
5.General recommendations
•
When the appliance is not in use unplug it and
turn off the tap.
•
Before cleaning or carrying out maintenance
switch off the appliance and disconnect it from
the mains supply.
•
To clean the outside of the appliance, use a
neutral detergent and a damp cloth.
•
Do not use abrasive detergents.
•
Do not attempt to force the door open.
•
If necessary, the power cable may be replaced
with an identical one obtained from our
After-Sales Service. The power cable must only
be replaced by a qualified technician.
6.EC Declaration of Conformity
•
This appliance has been designed, constructed
and distributed in compliance with the safety
requirements of EC Directives:
73/23/EEC Low Voltage Directive
89/336/EEC Electromagnetic Compatibility
Directive
93/68/EEC CE Marking Directive .
14
Page 4
DESCRIPTION OF THE APPLIANCE
3gb20020.fm Page 15 Tuesday, February 24, 2004 4:07 PM
Black process 45.0° 150.0 LPI
1.
Worktop
2.
Control panel
3.
Detergent dispenser
4.
Door
5.
Door handle
•
To open the door press the button inside
the handle and pull.
•
Close the door by pushing it firmly (the lock
3
7
1
2
4
5
will click into place)
6.
Filter (behind cover)
7.
After-Sales Service sticker (inside door)
8.
Adjustable feet
9.
Technical specifications sticker (inside cover)
8
6
9
Minimum housing dimensions
Width 595 mm
Height 850 mm
Depth (depending on the appliance) 395 or 335 mm / 530 or 580 mm
FILLING THE DETERGENT AND ADDITIVES
1.
Pull out the detergent dispenser completely, until the limit.
The dispenser has three chambers.
2.
Add the detergent:
•
Programme with pre- and main wash
•
Main wash programme without prewash
•
Fabric softeners, conditioners and chlorine
bleach: no more than to
•
Stain remover
•
Water softener (water hardness class 4)
•
Starch (dissolved in water)
3.
Close the detergent dispenser completely.
Water hardness:
WATER HARDNESS
CATEGORY:
1
2
3
4
“MAX”
mark
soft water requires less detergent.
CHARACTERISTICS GERMAN
soft
average
hard
very hard
°dh
0-7
7-14
14-21
over 21
FRENCH
°fh
0-12
12-25
25-37
over 37
ENGLISH
°eh
0-9
9-17
17-26
over 26
15
Page 5
REMOVING THE FILTER
3gb20020.fm Page 16 Tuesday, February 24, 2004 4:07 PM
Black process 45.0° 150.0 LPI
1.
Stop the appliance and unplug it.
2.
Open the filter cover.
3.
Place a bowl beneath the filter.
4.
Slowly turn the filter anticlockwise without extracting
it as yet.
5.
Wait until all the water has drained.
6.
Now unscrew the filter completely and extract it.
7.
Remove any foreign items from the foreign body trap.
8.
Insert the filter and screw it in clockwise until it locks,
making sure it is hermetically closed.
9.
Close the cover.
10.
Pour 0.5 l of water into the detergent dispenser to
reactivate the “Eco System”.
11.
Connect the appliance to the electrical outlet.
12.
Select a programme and start it.
Check the filter two or three times a year and clean it if
necessary.
•
Check the filter if the appliance is not draining correctly
or if it fails to perform spin cycles.
IMPORTANT: Make sure the water has cooled
before draining the appliance.
DRAINING RESIDUAL WATER
•
To drain the residual water from the pump, tilt the appliance forwards and proceed as per points 8 and
10 of the previous chapter.
When should I drain residual water?
•
Before transporting (moving) the appliance.
•
If the appliance is installed in a room subject to sub-zero temperatures.
In this case the appliance should be drained after every wash.
16
Page 6
CARE AND MAINTENANCE
3gb20020.fm Page 17 Tuesday, February 24, 2004 4:07 PM
Black process 45.0° 150.0 LPI
Appliance exterior and control panel
•
Clean using normal household cleaner (do not
use abrasive products and no solvents).
•
Dry with a soft cloth.
Door seal
•
Clean with a damp cloth when necessary.
•
Check the condition of the door seal periodically.
Filter
•
Check and clean the filter two or three times a
year (see “Removing the Filter”).
Detergent dispenser (depending on model)
1.
Disengage the detergent dispenser by pressing the release lever in
the prewash compartment and extract it.
2.
Remove the siphon from the softener and bleach compartment .
3.
Wash all the parts under running water.
4.
Reposition the siphon and refit the detergent dispenser.
1.
Pull the detergent dispenser out fully.
2.
Remove all the parts and wash them under running water and
reposition them.
3.
Wipe any residual detergent from the dispenser.
4.
Carefully replace the detergent dispenser by inserting in the left
guide and pushing it in.
Water hose mesh strainer
Check and clean periodically.
For appliances with a straight water supply hose
1.
Turn off the tap.
2.
Unscrew the hose from the tap.
3.
Clean the internal strainer.
4.
Screw the supply hose back onto the tap.
5.
Unscrew the hose from the appliance.
6.
Remove the filter from the appliance with pliers and clean it.
7.
Refit the filter and screw the hose connection to the appliance.
8.
Turn on the tap and
water-tight.
ensure that the connections are completely
TRANSPORT / HANDLING
Never move the appliance by carrying it by the worktop.
1.
Unplug the appliance.
2.
Turn off the tap.
3.
Disconnect the inlet and drain hoses.
4.
Eliminate all water from the hoses and from the appliance (see “Removing the Filter”,
“Draining residual water”).
5.
Fit the transport bolts (obligatory) (see “Installation”).
17
Page 7
INSTALLATION
B
A
B
A
A
A
1
3gb20020.fm Page 18 Tuesday, February 24, 2004 4:07 PM
Black process 45.0° 150.0 LPI
Remove the transport bolts
For washing machines:
1.
Slacken the three or four bolts (A) (according to
model) with the spanner supplied.
2.
Unscrew the bolts by hand.
For washer dryers:
1.
Slacken and remove the screws “A” which lock the
drum during transport by following the instructions
given at the side.
2.
Unscrew the bolts by hand.
ABA
A
A
B
A
1
For washing machines:
3.
Hold the screws together with the plastic spacers and
remove them. Keep the transport bolts for future use.
4.
Close the holes with the plastic covers (supplied
with the documents).
For washer dryers:
3.
Insert a screwdriver into the empty holes and tilt to
remove the plastic spacers (C) (transport bolts) and
retrieve them. Keep the transport bolts for future use.
For both washing machines and washer dryers:
Note:
If the plastic spacers remain inside the appliance: Open
the rear panel by removing the twelve screws, remove
the spacers and replace the panel.
Refit the transport bolts
Fit the transport bolts before transporting the
appliance as follows:
For washing machines:
1.
Pry off the plastic covers with a screwdriver and
remove them.
2.
Insert the transport bolts, performing the steps for
removal in reverse order.
For washer dryers:
1.
Disconnect the plug, remove the inlet and drain hoses.
2.
Unscrew fixing screws “B” on the rear panel and remove it.
3.
Insert the four screws “A” of the safety catch in the
four rubber bushes, then put the four spacers “C” on
the screws behind the panel.
4.
Position the rear panel on the appliance, first tighten
the four screws “A” of the safety catch for
transportation to the rear part of the tub, then use
screws “B” to fit the panel to the appliance.
4
3
C
18
Page 8
Adjust the feet
3gb20020.fm Page 19 Tuesday, February 24, 2004 4:07 PM
Black process 45.0° 150.0 LPI
If the floor is uneven, adjust the levelling feet as required (do
not insert pieces of wood, cardboard etc. under the feet):
Loosen the locknut using the wrench provided.
1.
Adjust the height of the foot, turning it by hand.
2.
Tighten the locknut anticlockwise towards the appliance.
3.
If the appliance is to be installed on a wooden floor, distribute the
weight by placing it on a 60 x 60 (or 40) cm sheet of plywood at
least 3 cm in thickness.
Secure the plywood sheet to the floor.
Worktop for built-under models.
The appliance must only be installed beneath a continuous fitted kitchen worktop.
Unplug the appliance.
1.
Unscrew the worktop fixing screws from the rear of the appliance.
2.
Lift the worktop slightly to free it from the housing of the top, then slide it forward to disengage it from
3.
the control panel, and remove. Install the cover panel following the relative instructions.
Refit the fixing screws and tighten them.
4.
Plug the appliance back in.
5.
Connect the water inlet hose
For models with straight hose:
Insert the dirt strainer (included in the accessories) into
1.
the threaded tap coupling and the coupling between the
hose and the appliance.
Carefully screw the hose connection onto the tap,
2.
preferably by hand.
Make sure there are no kinks in the hose.
3.
Carefully screw the hose connection to the appliance
4.
inlet, preferably by hand.
Turn the tap on fully and check that the joints at the
5.
appliance and the tap are watertight.
If the hose is too short, replace it with a suitable length of pressure
resistant hose (1000 kPa min, EN 50084 approved type).
Check the hose regularly for brittleness and cracks and
replace if necessary.
The appliance can be connected without a non-return valve.
Connect the water drain hose
Unhook the drain hose from the right clip (A).
1.
Attention: do not unhook
Connect the drain hose to the siphon or hook it over the
2.
edge of a sink by means of the “U” bend supplied.
Make sure there are no kinks in the hose.
3.
Secure the hose so that it cannot fall down while the
4.
appliance is running.
Small hand basins are not suitable.
If the hose is to be inserted directly into the drain pipeline,
the inside diameter of the pipe must be appropriate in
relation to the diameter of the drain hose.
If you need to add an extension, use a flexible hose of the
same type. Secure the unions with screw-on hose clips.
Max. drain hose length: 2.50 m
Max. drain height: 90 cm
Min. drain height: 60 cm
the left drain hose connection.
A
19
Page 9
ELECTRICAL CONNECTION
3gb20020.fm Page 20 Tuesday, February 24, 2004 4:07 PM
Black process 45.0° 150.0 LPI
For Great Britain only
Warning - this appliance must be earthed
Fuse replacement
If the mains lead of this appliance is fitted with a BS 1363A
13amp fused plug, to change a fuse in this type of plug use
an A.S.T.A. approved fuse to BS 1362 type and proceed as
follows:
1.
Remove the fuse cover (A) and fuse (B).
2.
Fit replacement 13A fuse into fuse cover.
3.
Refit both into plug.
Important:
The fuse cover must be refitted when changing a fuse and
if the fuse cover is lost the plug must not be used until a
correct replacement is fitted.
Correct replacement are identified by the colour insert or
the colour embossed in words on the base of the plug.
Replacement fuse covers are available from your local
electrical store.
Socket outlet / plug
If the fitted plug is not suitable for your socket outlet,
please contact Whirlpool Service on 0870 600 8989 for
further instruction. Please do not attempt to change plug
yourself. This procedure needs to be carried out by a
qualified Whirlpool technician in compliance with the
manufactures instructions and current standard safety
regulations.
For the Republic of Ireland only
The information given in respect of Great Britain will
frequently apply, but a third type of plug and socket is also
used, the 2-pin, side earth type. In this case, the wire which
is coloured GREEN AND YELLOW must be connected to
the EARTH contact, and the two wires to the two pins,
irrespective of colour. The supply to the socket must be
fitted with a 16 amp fuse.
20
Loading...