Whirlpool MK9167XAQ1, MK9167XAB1 Installation Instructions
INSTALLATION INSTRUCTION
FOR USE WITH WHIRLPOOL MICROWAVE OVEN MODELS: MT91 6OXYQ MT91 60XYB
I UL LISTED - FOR USE OVER GAS & ELECTRIC HEAT SOURCE INCLUDING MODELS. St31 30PER. SB
FOR WHIRLPOQL TRIM-KIT MODELS: MK9167XAQl. MK9167XABl
(KEEP FOR FUTURE REFERENCE]
OPEX. RB760PXY I
STEP 1
.-__
PART LIST
q-b
STEP 3
1. Disconnect mrcrowave and remove any loose
items insrde the oven before proceedrng wrth
rnstallation.
2. Detach Existing Strews(4) from the microwave
cabinet sides at locations as indicated.
Install Ducts DS and Dl 1 by re-attaching
3.
Exrsting Screwsf4) and using No. 10 Screws(Z)
as shown.
Duct D5
1 ‘I,’ No.6 Scrrws
Iparnted) 4
‘I,” No.8 Screws
2
Rcq’d
I/>- No. 10 Screws
lslottedl 2 Req’d
I/,‘ No.1 2 Screws
2
Rcs’d
Ilow profrlef 2 Req’d
REAR VIEW OF MICROWAVE
,,eg= Duct D7
Req’d
STEP 2
CUT-OUT DIMENSIONS
Herght - 16 ‘I,”
Length = 24 ‘/2”
Depth :- 23 ‘7,” (min.)
NOTE: If the wall is constructed
of drywall or sheet-rock maternal,
make sure there rs wood directly
behrnd rt for proper Installation.
STEP 4
1. Mark center positions for center-punch)
for the Ant!-Trp Bracket as shown.
Dimensions:
A = 1 ‘1,”
El = 3 Va”
c = 19 61,”
Microwave Oven
curour Opening
4. Position Duct D7 over microwave, coverwrg
rear exhaust vent. Loosely attach Duct
usrng No. 12 Screwsf21 as shown.
5. Lift the front of Duct D7 and peel backing off
double sided tape from the Duct bottom. Press
down firmly on Duct. Trghten No. 12 Screws(Z)
at the back.
PART NO. 4386552
2. Drrll pilot holes as required
3. Install Anti-Tip Bracket
using I/r’ No.8 Strews(2)
as shown.
@$ ‘I,’
No.8 Screws
Ant!-Trp Bracket
Page
1
STEP 5
cutout
1. Place mtcrowave oven in the openrng
of the cut-out. Be c~relul
bend the AnWTip Flange. Flange
must be flat to cut-out floor to
engage correctly wrth AnnTip
Bracket as shown.
2. Plug in microwave oven
3. Center mrcrowave oven withm
the cut-out opening and slide
oven in place.
nor
lo
Anti-Tip Assembly
\
VIEW FROM BACK
OF MLCROWAVE
Flange
6 STEP
After oven 1s In place, ensure
1
IIIII:IOW~~ IS xcurarelv cunrered.
Dnll pilot holes through Positioning
2
Flanges. Secure the Ducts as shown
USIINJ
1 ” No.8 LOW Prohle Screwsl2).
-0w Profile
Screws
\ /
u
;fi ~\
*
v
L Positioning
;
Flanges
Opening
STEP 7
1. Place Trim Frame over microwave
2. Make sure Frame is level and
the microwave cenrered within the
Frame. Mark center positions(41
through the mounttng holesf4)
of the Frame.
3. Remove Frame and dnll pilot boles(4)
1.1 10’ DIA or use #35 drill).
4. Attach Frame using 1 I/>* No.6
Pamted Screwsf41.
PART NO. 4386552
No 6 painted’
Screw
STEP 8
1, Your Tram-Kn is now fully
Installed. Replace any loose
Items that might have been
removed from the oven.
2. Please keep thus installation
instructron for future reference.
Page 2
Loading...