WHIRLPOOL MK9167XAQ, MK9167XAB Installation Instructions

/NSTALLAT/ON

/b/STf?UCT/ON FOR WHIRLPOOL TRIM-KIT MODELS: MK9167XAQ. MK9167XAB

FOR USE WITH WHIRLPOOL MICROWAVE OVEN MODELS: MT9160XYQ MT9160XYB
[ UL USTED - FOR USE OVER GAS & ELECTRIC HEAT SOURCE INCLUDING MODELS: SB130PER. S

(KEEP FOR FUTURE REFERENCE)

‘GOPEX. R0760PXY ]

STEP 1

PART UST

Aluminum Venl

3 STEP

1. Disconnect microwave and remove any loose
items inside the oven before proceeding with
installation.

2. Detach Existing Strews(4) from the microwave
cabinet sides at locations as indicated.

3. Install Ducts DS and Dl 1 by m-attaching Existing
Strews(4) and using No.10 Strews(2) as shown.

4. Position Duct D7 over microwave, covering

rear exhaust vent. Loosely attach Duct
using No.12 Screm(2) as shown.

5. Lift the front of Duct D7 and peel backing off
double sided tape from the Duct bottom. Press
down firmly on Duct. Tighten No.12 Screws(p)

at the back.

No. 10 Screws
(slotted) 2 Req’d

w No.12 Screws

Q

REAR YlEW OF MICROWAVE

2 Req’d

Low Profile Screws

B Aeq’d

Spring Clips

4 Req’d

- Duct D7

2 STEP

Microwave Oven

CUT-OUT DIMENSIONS

Cutout Opening

Height = 16 ‘/,
Length = 24 ‘/2’
Depth = 23 ‘/,’ (min.)

STEP 4

1. Mark center positions (or center-punch)
for the An&Tip Bracket as shown.

Dlmensions:

A = 1 ‘lo
0 = 3 ‘Ia.
c = 19 “I0

2. Drill pilot holes as required.

3. Install Anti-Tip Bracket
with Low Profile
ScrewsQ) as shown.

Low Profile Screws 7

-0--

r---

‘\

‘\\

\

‘\\

Cutout Floor

\

PART NO. 4313743

Page 1

5 STEP

Place microwave oven in the opening
of the cut-out. Be careful nof lo

bend the Anti-Tip Flange. Flange
must be flat to cut-out floor to
engage correclly vvith Anti-Tip
Bracket as shown.

Plug in microWave oven.
Center microwave oven within

the cut-out opening and slide
oven in place.

After oven is in place, ensure
microwave is accurafely cenfered.

Drill pilot holes through
Positioning Flanges and install
Low Profile Screws(Z) at the
front of the Ducts as shown.

Anti-lip Assembly

1. Mark center positions (or center
the pilot holes(4) as shown. Dim.A is
measured from the cut-out bottom and
Dim.B is from the cutout side. The
top hole is determined by Dim.C.

Dlm.A = ‘/a’
Dlm.B = ‘/,’ (mln.)
Dlm.C = 17 “lls

2. Drill pilot holes and install the Spring
Clips(4) using Low Profile ScreW(4).
Note that the top Clips face up and
the bottom Clips face down as shown.

3. The Spring Clips are provided with a
slotted hole for fine adjustments as required.

punch) for

Gh

Top Clip Position

Position

Opening

‘EP

s7

Place Trim Frame over the microwave.

1.

Make sure microwave is centered within

the Frame. Firmly push Frame against
the wall at the four Spring Clip
locations as shown.

Check Frame for fighf M. If Frame

2.
is loose, remove the Frame and make
necessary adjustments by loosening the
Screw, re-posttioning the Clips and
re-tightening the Screw. Reattach
Frame as above.

PART NO. 4313743

8 STEP

1. Your Trim-Kii is now fully
installed. Replace any loose
items that might have been
removed from the oven.

2. Please keep this installation
instruction for Mure reference.

Page 2