Whirlpool MK9160XAQ1, MK9160XAB1 Installation Instructions
INSTALLATION INSTRUCTION
FOR USE WITH WHIRLPOOL MICROWAVE OVEN MODELS: MT91 6OXYD. MT91 GOXYB
1 UL LISTED - FOR USE OVER ELECTRIC HEAT SOURCE INCLUDING MODELS: RB260PXY. Rf3220PX’
FOR WHIRLPOOL TRIM-KIT MODELS: MK91 GOXAQl, MK916OXABl
(KEEP FOR FUTURE REFERENCE1
STEP 1
PART LIST
Aluminum Vent
=
STEP 3
1. Disconnect microwave and remove any loose
items inside the oven before proceeding with
installation.
2. Detach Existing Screwsf4) from the microwave
cabinet sides at locations as indicated.
3. Install Ducts D5 and Dl 1 by re-attaching
Existing Strews(4) and using No. 10 Screws121
as shown.
Duct D5
_ NO.12
1 ‘iI- No.6
bwmdl 4 Req’d
‘I,- No.8 Screws
‘I,- No. 10 Screws
Islotted) 2 Req’d
‘I,‘ No.1 2 Screws
l- No.8 Screws
(low proHe) 2 Req’d
REAR VIEW OF MICROWAVE
Screws
2 Req’d
2 Req’d
STEP 2
CUT-OUT DIMENSIONS
Height = 16 ‘I,’
Length = 28 l/r.
Depth = 23 ‘1.’ (min.1
NOTE: If the wall is constructed
of drywall or sheet-rock material,
make sure there is wood directly
behind it for proper installation.
4 STEP
1. Mark center positions for center-punch)
for the Anti-Tip Bracket as shown.
Dimensions:
A = 3 ‘I,”
B = 3 ‘1.”
c = 19 S/,”
Microwave Oven
Cutoul Opening
I‘----- p-.Yh
I ’
B
xe----
‘\
Cutout Floor
-i-
-N
1 1
Butll-in Oven
Culoul Opcnin 1
--
‘\
\
’ \\
‘. .
C
‘\
B-
4
B
4. Position Duct 07 over microwave, covering
rear exhaust vent. Loosely attach Duct
using No. 12 Screws(Z) as shown.
5. Lift the front of Duct D7 and peel backing off
double sided tape from the Duct bottom. Press
down firmly on Duct. Tighten No.1 2 Screws(Z)
at the back.
PART NO. 4386554
2. Drill pilot holes as required.
3. Install Anti-Tip Bracket
using ‘/r- No.8 Screwsf2)
as shown.
7 ‘I,’ No.8 Screws
Anti-Tip Bracket
Page 1
5 STEP
6 STEP
1,
Place microwave oven in the opening
of the cut-out. Be carelul nor to
bend rhe Anti-Tip F/.Wrge. Flange
musr be flat to cut-out floor to
engage correctly with Anti-Tip
Bracket as shown.
2. Plug in microwave oven.
3. Center microwave oven within
the cut-out opening and slide
oven in place.
STEP 7
1.
Place Trim Frame over microwave.
2.
Make sure Frame is level and
the microwave centered within the
Frame. Mark center positionsf4)
through the mounting holes141
of the Frame.
3.
Remove Frame and drill pilot holesl4)
1.1 10’ DIA or use #35 drill).
Anti-Tip Assembly
L Flange
VIEW FROM BACK
OF MICROWAVE
1, After oven is in place, ensure
microwave is accurarely centered.
2. Drill pilot holes through Positioning
Flanges. Secure the Ducts as shown
using 1” No.8 Low Profile ScrewsfZI.
STEP 8
1, Your Trim-Kit is now fully
installed. Replace any loose
items that might have been
removed from the oven.
2. Please keep this installation
instruction for future reference.
1”
Low Profile
*
J
\
,’
\
,‘” ,.’
cutout
Opening
P;f.saf;t;;ng
4.
Attach Frame using 1 ‘I,” No.6
Painted Screwsfrll.
PART NO. 4386554
No.6 painted’
Screw
Page 2
Loading...