WHIRLPOOL MK8130XAQ, MK813OXAB Installation Instructions
INSTALLATION INSTRUCT/ON
FOR USE WITH WHIRLPOOL MICROWAVE OVEN MODELS: MC8130XAQ. MC8130XAE
[ UL USTED - FOR USE OVER ELECTRIC HEAT
FOR WHIRLPOOL TRIM-KIT MODELS: MK8130XAQ. MK813OXAB
SOURCE INCLUDING MODELS: RB260PXY, RB220PXY ]
WEEP FOR FUTURE REFERENCE)
I
1 STEP
PART UST
Aluminum Vent
3 STEP
1. Disconnect microwave and remove any loose
items inside the oven before proceedina with
installation.
2. Detach Existing Strews(6) from the
microwave oven at locations as indicated.
3. Install Duct D17 by re-attaching
Existing Strews(4) as shown.
4. Position Duct D16 over microwave,
top exhaust vent. Loose/v attach Duct
using remaining Exiting Screws(P) as shown,
5. Lii the front of Duct D16 and peel backing off
double sided tape from the Duct bottom. Press
down firmly on Duct. lighten Existing ScremQ)
at the back.
covering
Low Profile Screws
a Aeq’d
Spring Clips
4 Req’d
STEP 2
CUT-OUT DIMENSIONS
Height = 17 I/,’
Length = 26 ‘/1’
Depth = 23 ‘/,’ (min.)
4 STEP
1. Mark center positions (or center-punch)
for the Anti-Tip Bracket as shown.
Dlmenslons:
A = 11 ‘I,’
B = 3 ‘Ia’
C = 16 ‘1;
2. Drill pilot holes as required.
3. Install Anti-Tip Bracket
with Low Profile
Strews(2) as shown.
Anti-Tip Bracket
Microwave
Oven
<---
‘\
’ \\
Cutout Floor
_---
\
‘\
‘\
PART NO. 4350409
Page 1
5 STEP
Place microwave oven In the opening
I.
of the cut-out. Be carelul nor lo
bend fhe An&Tip Flange. Flange
must be flat to cut-out floor to
engage correctly with Anti-Tip
Bracket as shown.
Plug in microwave oven.
2.
Center microwave oven within
3.
the cut-out opening and slide
oven in place.
4.
After oven is in place, ensure
microwave is accurately cenfered.
Drill pilot hole through
5.
Positioning Flange end install
Low Profile Screw(I) at the
front of the Duct as shown.
Antl-Tip Assembly
Flange
Mark center positions (or center punch) for
1.
the pilot holes(4) as shown. DimA is
measured from the cut-out bottom and
Dim.B is from the cut-out side. The
top hole is determined by Dim.C.
Dlm.A = ‘/,;
Dlm.B = ‘/,’ (mln.)
Dlm.C = 19 ‘/<
2. Drill pilot holes and install the Spring
Clips(4) using Low Protile Strews(4).
Note that the top Clips face up and
the bottom Clips face down as shown
3. The Spring Clips are provided with a
slotted hole for fine adjustments as required.
Top Clip Posilion
Position
Dim. C
Opening
7 STEP
Position Trim Frame such that the notch is
located in the boftom /eff comer. Hook Frame
under the hinge lab located on the bottom
left of the microWave oven and place Frame
completely over the microwave.
Make sure microwave is centered within
the Frame. Firmly push Frame against
the wall at the four Spring Clip
locations as shown.
Check Frame for tiglrf fit. If Frame
is loose, remove the Frame and make
necessary adjustments by loosening the
Screws. re-positioning the Clips and
re-tightening the Screws. Reattach
Frame as above.
PART NO. 4350409
Notch
8 STEP
Your Trim-Kit is now fully
I.
installed. Replace any loose
items that might have been
removed from the oven.
2. Please keep this installation
instruction for future reference.
Page 2
Loading...