Whirlpool MK 6124 XEQ, MK 6124 XEB, MK 6124 XES Installation Instructions
INSTALLA T/ON/NSTRUCT/ON
FOR USE WITH WHIRLPOOL MICROWAVE OVEN MODELS: MT61 ZOXEQ, MT61 20XEB, KCMSl25EWH. KCMS125ESB
.:
f UL LISTED - FOR USE OVER ELECTRIC HEAT SOURCE INCLUDING MODELS: RBS24BPD, RBS245PD. KEBll410, KEBSl470, SB130PED. SBl GOPEE 1
FOR WHIRLPOOL
TRIM-KIT MODELS: MK6124XEQ. MK6124XEB. MK6124XES
(KEEP FOR FUTURE REFERENCE)
1 STEP
PART LIST
Aluminum Vent
STEP 3
1. Disconnect microwave znd remove any
loose items inside the oven before
proceeding with installation.
2. Install Duct DlB using ‘/2” No.8
Screw as shown.
1 ‘I,” No.6 Screws
t
‘II‘ No.6 Screws
Duct
D18 1,. No.8 Screws
llow profile) 2 Req’d
B
REAR VIEW OF MICROWAVE
4
Req’d
3 Req’d
STEP 2
CUT-OUT DIMENSIONS
Height = 15 ‘/,’
Length = 22 ‘I,’
Depth = 23 ‘/*” lmin.)
NOTE: If the wall is constructed
of drywall or sheet-rock material,
make sure there is wood directly
behind it for proper installation.
1. Mark center positions for center-punch)
for the Anti-Tip Bracket as shown.
Dimensions:
A=
9 l/4”
B=
3 5/8”
16 l/2”
C=
2. Drill pilot holes as required.
Microwave Oven
Cutout Opening
Cutout Floor
Cutout Opening
r I
I 1 I
1
1
PART NO. 4386669
. . :
Duct 018
‘I,‘ No.6 Screw
3. Install Anti-Tip Bracket
using 1/2* No.8 Screws(Z)
as shown.
Ann-TIP Bracket
Page 1
5 STEP
STEP 6
1. Place microwave oven in the opening
of the cut-out. Be careful nor to
bend the Anti-Tip Flange. Flange
musl be flat to cut-out floor to
engage correctly with Anti-Tip
Bracket as shown.
2. Plug in microwave oven.
3. Center microwave oven within
the cut-out opening and slide
oven in place.
7 STEP
Place Trim Frame over microwave.
1.
2. Make sure Frame is level and
the microwave cenfered within the
Frame. Mark center positions(4)
through the mounting holes(41
of the Frame.
3. Remove Frame and drill pilot holesf41
f.1 10” DIA or use #35 drill).
Anti-Tip Assembly
VIEW FROM BACK
OF MICROWAVE
-Pilot Hole
\
1. After oven is in place, ensure
microwave is accwatelv centered.
2. Drill pilot holes through Positioning
Flange. Secure the Duct as shown
using 1” No.6 Low Profile ScrewslZJ.
8 STEP
1. Your Trim-Kit is now fully
installed. Replace any loose
items that might have been
removed from the oven.
2. Please keep this installation
instruction for future reference
1” 1
:,,A
L
k
,f- 4
@i
?\
L
cutout
Opening
Positioninq
Flange -
4. Attach Frame using 1 ‘/*” No.6
Strews(4).
PART NO. 4386669
1 ‘jl” No.6 Screw
Page 2
Loading...