MICROWAVE OVEN BUILT-IN TRIM KIT
INSTALLATION INSTRUCTIONS
Built-In Trim Kit Models MK2167, MK2160
UL listed for use over any electric or gas built-in oven, up to 30" (76.2 cm) wide
INSTRUCTIONS D’INSTALLATION
GARNITURE ENCASTRÉE POUR FOUR À MICRO-ONDES
Garniture encastrée pour modèles MK2167, MK2160
Homologation UL pour utilisation au-dessus de tous les fours encastrés électriques ou gaz, jusqu’à 30" (76,2 cm) de largeur
Table of Contents / Table des matières
MICROWAVE OVEN SAFETY ................................................... |
1 |
INSTALLATION INSTRUCTIONS.............................................. |
2 |
Tools and Parts ....................................................................... |
2 |
Location Requirements........................................................... |
2 |
Required Cutout Dimensions.................................................. |
2 |
Trim Kit Frame Dimensions..................................................... |
3 |
Electrical Requirements .......................................................... |
3 |
Prepare Microwave Oven........................................................ |
3 |
Prepare Cutout/Cabinet Opening ........................................... |
4 |
Install the Microwave Oven..................................................... |
5 |
Install Trim Kit Frame .............................................................. |
6 |
SÉCURITÉ DU FOUR À MICRO-ONDES ........................................... |
7 |
INSTRUCTIONS D’INSTALLATION .................................................... |
7 |
Outillage et pièces............................................................................. |
7 |
Exigences d'emplacement................................................................ |
7 |
Dimensions nécessaires de l'ouverture d'encastrement.................. |
8 |
Dimensions du cadre de la trousse de garniture.............................. |
8 |
Spécifications électriques ................................................................. |
9 |
Préparation du four à micro-ondes................................................... |
9 |
Préparation de l'ouverture d'encastrement .................................... |
10 |
Installation du four à micro-ondes .................................................. |
11 |
Installation du cadre de la trousse de garniture ............................. |
12 |
MICROWAVE OVEN SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.” These words mean:
DANGER
WARNING
You can be killed or seriously injured if you don't immediately follow instructions.
You can be killed or seriously injured if you don't follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.
W10532204A
INSTALLATION INSTRUCTIONS
Tools and Parts
Tools Needed
Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.
■ |
Measuring tape |
■ |
Drill |
■ |
Pencil |
■ |
7/64" drill bit |
■Phillips screwdriver
Parts Supplied (not shown to scale
|
|
|
|
|
|
|
|
Rails (2) |
Bottom duct |
Trim kit frame |
|
|
|
|
|
Short screws (14) |
Long wood screws (6 - painted) |
(11 + 3 extra) |
(4 + 2 extra) |
Location Requirements
The microwave oven may be installed over a built-in oven. If installing over a built-in oven, make sure there is a minimum of 3" (7.6 cm) between the top of the lower oven cutout and the microwave oven cutout floor.
The microwave oven may also be installed in a cabinet by itself (without a built-in oven below). For best usability, we recommend a minimum distance of 36" (91.4 cm) from the floor to the cutout floor.
Make sure the surrounding cabinetry has clearance to open and close freely. Allow a clearance of at least 1⁄" (4.0 cm) below the cutout floor (3" [7.6 cm] for installation above a built-in oven), and a clearance of at least 2" (5.1 cm) above the cutout opening.
|
A |
|
2" |
2" |
|
(5.1 cm) |
(5.1 cm) |
|
B |
B |
|
1⁄" |
3" |
|
(4.0 cm) |
||
(7.6 cm) |
||
|
||
|
C |
|
D |
36" |
|
(91.4 cm) |
||
|
||
E |
|
A. Upper cabinet |
D. Lower cabinets |
B. Microwave oven cutout |
E. Floor |
C. Lower oven cutout |
|
Required Cutout Dimensions |
|
|
For minimum depth requirements, see chart. |
|
1¹⁄" |
|
(2.7 cm) |
|
6" |
|
(15.2 cm) |
17" (43.2 cm) |
|
min. |
A |
17¹⁄" (43.5 cm) |
23¹⁄" (58.7 cm) |
max. |
|
3" |
1¹⁄" |
(2.7 cm) |
|
(7.6 cm) |
|
B
DC
A.Trim kit frame overhang
B.Cutout for lower oven
C.Recommended region for receptacle location (no less than 6" [15.2 cm] to the right of cutout centerline)
D.Cutout centerline
Receptacle Location |
Minimum Depth |
Within recommended |
18" (45.7 cm) with flush receptacle; |
region |
21" (53.2 cm) with non-flush receptacle |
|
|
|
|
Outside recommended |
19¹⁄" (49.5 cm) with flush receptacle; |
region |
22¹⁄" (57.2 cm) with non-flush |
|
receptacle |
|
|
NOTES:
■Depth requirements depend upon receptacle and its location within or outside of recommended region. See illustration and chart above.
■Height dimension is critical: 17" (43.2 cm) minimum, 17¹⁄" (43.5 cm) maximum.
■Width measurement has ±1/16" (2 mm) tolerance.
■3" (7.6 cm) minimum dimension is from lower oven cutout ceiling to microwave oven cutout floor.
■Trim kit frame extends 1¹⁄" (2.7 cm) above and below the cutout opening.
2
Trim Kit Frame Dimensions
|
|
|
|
|
|
|
|
26 ⁄ " (68.2 cm)** |
|
||||
|
|
|
|
|
|
|
|
29³⁄ " (75.6 cm)** |
|
||||
|
|
|
|
|
|
|
|
22³⁄ " (57.8 cm) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
||
19¹⁄ |
" |
|
|
|
|
3 ⁄ " |
|
|
|
||||
|
|
|
|
(8.7 cm) |
|
|
|||||||
(48.6 |
cm) |
|
|
|
|
|
|
12¹⁄ |
" |
|
|||
|
|
|
|
|
|
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
(31.1 |
cm) |
|
||
|
|
|
|
|
|
|
|
2¹⁄ " (5.2 cm)** |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
3¹⁄ " (8.9 cm)** |
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1³⁄ " (3.0 cm)
*27" (68.6 cm) trim kit
**30" (76.2 cm) trim kit
Electrical Requirements
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death, fire, or electrical shock.
Observe all governing codes and ordinances.
Required:
■A 120 volt, 60 Hz, AC only, 15or 20-amp electrical supply with a fuse or circuit breaker.
Recommended:
■A time-delay fuse or time-delay circuit breaker.
■A separate circuit serving only this microwave oven.
GROUNDING INSTRUCTIONS
■For all cord connected appliances:
The microwave oven must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. The microwave oven is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded.
WARNING: Improper use of the grounding plug can result in a risk of electric shock. Consult a qualified electrician or serviceman if the grounding instructions are not completely understood, or if doubt exists as to whether the microwave oven is properly grounded.
Do not use an extension cord. If the power supply cord is too short, have a qualified electrician or serviceman install an outlet near the microwave oven.
SAVETHESE INSTRUCTIONS
Prepare Microwave Oven
1.Unplug microwave oven before proceeding with installation.
2.Remove any loose items inside microwave oven.
3.Gently turn microwave oven onto its top, with the door facing forward (toward installer).
4.Align the two rails on the microwave oven bottom, as shown, making sure the flanges are forward and pointing up.
A B C
D |
E |
A. Rails (2) |
D. Flanges |
B. Microwave oven bottom |
E. Door |
C.Short screws (4)
5.Secure the rails to the microwave oven bottom using four short screws.
3
Prepare Cutout/Cabinet Opening
1.On the cutout floor, find and mark the centerline.
2.Place the bottom duct in the opening, with the flange resting against the bottom front facing of the opening.
A B C
D |
E |
A. Cutout floor |
D. Bottom duct flange |
B. Centerline |
E. Front facing |
C.Bottom duct
3.Align the center arrows on the bottom duct with the centerline drawn in Step 1 above.
4.Mark the three mounting holes through the bottom duct onto the cutout floor.
A |
B
A.Short screws (3)
B.Bottom duct mounting holes
5.Using 7/64" drill, drill pilot holes into the three holes marked in Step 4.
6.Realign and install the bottom duct with three short screws.
7.Using 7/64" drill, drill pilot holes through the four mounting holes of the bottom duct flange into the bottom front facing of the cutout/cabinet opening.
A B
A. Bottom duct flange
B. Mounting holes
A B
A.Bottom duct
B.Center arrows, aligned with centerline
4