Machine operation
Additional information (including troubleshooting and service) can be found in the individual chapters of the
instructions for use.
Sort laundry according to
care symbols:
Do not tumble dry
Suitable for tumble drying -
at low drying temperature
Suitable for tumble drying
Sort by:
Material thickness:
separate laundry according to weight (e.g. dry towels and thin underwear
separately).
Type of material:
Degree of drying:
Do not tumble dry:
with metallic decorations, bulky items such as sleeping bags, etc.
Whenever there is greater load than the dryer can handle,
Cotton (linen); synthetic textiles (easy care).
Cupboard dry, iron dry etc.
Woollens, silk, nylon stockings, delicate embroidery, fabrics
Preparing laundry
Opening door
Loading dryer
Selecting programme
Selecting options
(if available)
Starting dryer
Programme end -
unloading dryer
Switching dryer off
Please note:
thoroughly in plenty of water before drying. Never dry rubber objects or objects stained with vegetable oils in the dryer.
Only use additives/plastic items specified as dryer safe and rinse items that have been treated with stain remover
Check that all fastenings are closed and that pockets are empty. Please ensure that
there are no cigarette lighters in the wash. Turn laundry inside out.
Pull the door handle. If the child safety lock is activated, please deactivate it
(additional information can be found in the “Door Reversibility/Child Safety Lock”
chapter of the instructions for use).
Place laundry loosely in the drum to achieve equal drying throughout. Then close
the door.
Select the drying programme required by turning the programme selector knob
(for information, refer to programme table).
Select the option required by pressing the corresponding button.
The indicator lamp above the relevant button lights up to confirm your selection.
A fast blinking led indicates a wrong selection is made (incompatible options). Press
the button again to cancel the option.
The drying programme is started by pressing the
The relevant indicator lamp lights up.
Changing programme selection:
drying, the dryer stops. The Drying indicator lamps flashes. To operate the new
programme, again press the
Interrupting programme:
programme selector knob to “ ” and press the
least 5 minutes before opening the door to allow the dryer to cool down. For your
safety the drying cycle stops automatically if you open the door. To resta rt, after door
opening, close the door and press the
Warning:
items are quickly removed and spread out so that the heat is dissipated.
The final part of a tumble dryer cycle occurs without heat (cool down cycle) to
ensure that the items are left at a temperature that ensures that the items will not
be damaged.
Set the programme selector knob to “Off” “ ”.
Cleaning the lint filter:
it. Brush lint using a soft brush or your fingertips. Close lint filter and push firmly
back into place.
Emptying water container:
the container when empty by pushing it completely back into place.
If required, activate child safety lock (additional information can be found in the “Door
Reversibility/Child Safety Lock” chapter of the instructions for use).
Never stop a tumble dryer before the end of the drying cycle, unless all
T ake the laundry out of the dryer. The drying process is complete
End:
and the anti-crease phase has been reached (active).
Anti-Crease:
an automatic anti-crease cycle will operate for maximum 60 min. The
drum rotates at regular intervals to prevent the laundry from creasing.
Open door, pull lint filter up and out of machine and open
If the programme selected is changed during
“Start (Pause)”
To interrupt the dryer during the drying cycle, set the
“Start (Pause)”
If the laundry is not removed at the end of the drying cycle,
Pull container out by the handle and empty. Replace
“Start (Pause)”
button.
“Start (Pause)”
button again.
button.
button. Wait at
1
Programmes / Drying levels
Drying
times
Cotton
*
Mixed fabrics
plus
Delicate
Overview of programmes Options
Type o f texti l e
Multi-layered, thick laundry such as:
terry towels, dish cloths and dry
towels, bed linen, underwear, terry
towelling bath robes.
Similar types of laundry which do not
require ironing such as: dry towels, bed
*
linen, underwear, baby clothes, Tshirts, cotton socks.
Laundry which requires ironing such as:
bed and table linen, dry towels, Tshirts, polo shirts, work clothes.
Laundry with thick, multi-layered areas
such as: bed and table linen, track suits,
anoraks, blankets.
Laundry which does not require ironing
such as: shirts, blouses,
*
T-shirts, sportswear.
Laundry which requires ironing such as:
trousers, dresses, skirts, shirts, blouses.
Low drying intensity for delicates and
items labelled with , such as:
trousers, dresses, shirts, blouses.
Fabrics
Cotton or linen hot wash /
coloured laundry
Max. 7 kg
Synthetic, mixed fibre or cotton
easy care (ironing not required)
Laundry made from synthetic
fibres such as polyamide, nylon,
laundry
Max. 3.5 kg
polyacrylic, etc.
Max. 2.5 kg
Volume
of load
kg
3.0
7.0
3.0
7.0
3.0
7.0
1.0
3.5
1.0
3.5
1.0
3.5
X X X X X X
X X X X X X
X X X X X X
X - X X X X
X - X X X X
X - X X X X
2.5 X - X X X - 100’ 85’
Approximate
drying times
(in minutes)
Very
Wet
wet
load
load
100’
90’
180’
160’
85’
70’
160’
120’
70’
60’
120’
100’
50’
40’
90’
70’
40’
30’
80’
60’
30’
20’
70’
50’
Laundry is aired and
refreshed for 30 minutes
without heating.
Airing
Completes drying for min.
3-5 full size textiles
(suitable for all fabrics).
* Test programme in accordance with EN 61121.
- - - - - - - - -
- X - X X - -
2
...you want to
correctly care for
and clean your
dryer:
...you want to check
the dryer yourself
first:
(If your machine is not
functioning correctly,
please check the
following points before
phoning for the
customer service – also
refer to relevant chapter
in the instructions for
use)
How to proceed if ...
Clean the filter at the end of
every cycle.
Empty the water container at
the end of each drying cycle.
Clean the heat exchanger at
least every month.
(For further information see
chapter “Heat Exchanger” in
the Instructions for Use).
Drying takes too long / laundry
is not dry enough.
The dryer will not operate
(after a power failure, always
press the “Start (Pause)”
button).
Lint filter or water container
indicator lamp on.
Water droplets underneath
the dryer.
Replacing the drum light bulb
(if supplied).
All programme sequence
indicators blinking.
• Open the door.
• Pull the filter upwards.
• Open the filter.
• Brush lint using a soft brush or your fingertips.
• Close the filter.
• Push the filter back into place.
• Pull the handle to remove the water container.
• Empty the water container.
• Replace the water container when empty by
pushing it
completely
• Remove fibres in and around the water
evacuation hole at least once per month.
• Has the correct drying programme been
selected?
• Was the inserted laundry too wet (washing
machine spin speed less than 1000 rpm)?
• Is the lint filter dirty (filter indicator light on)?
• Is the heat exchanger dirty? (for more
information, refer to the instructions for use)
• Is the room temperature too high?
• Are the “ ” and “ ”
indicator lamps lighting up? The drying cycle is
complete and the laundry can be taken out.
• If the drying result does not meet your
expectation, select a more dry programme.
• Is the plug properly inserted into the mains
electricity socket?
• Is there a power failure?
• Has the fuse blown?
• Is the door properly closed?
• Has a drying programme been selected?
•Has the
• Has the Start delay option been selected?
• Is the lint filter clean?
• Is the water container empty?
• Has the water container been inserted correctly?
• Is the heat exchanger clean?
• Has the heat exchanger been inserted correctly?
• Has any fluff on the heat exchanger seal been
• Has any fluff on the door seal been wiped away?
• Has the water container been inserted
• If the inside lamp does not work, the bulb may
•Unplug the dryer.
• Open the door and unscrew the glass cover
• Replace the faulty bulb with a new one and
• Replacement bulb: Philips 15W, 230/240V, E14.
• Service call necessary.
“Start (Pause)”
wiped away?
correctly?
be faulty.
inside the drum.
screw the glass cover back on.
back in place.
button been pressed?
AFTER-SALES SE R V I C E
If the fault is still present once the above checks have been undertaken or should the fault occur for a second time, switch the machine off.
Please contact your After-Sales Service representative (for more information, refer to the warranty manual).
Please have the following details ready when calling your after-sales service representative:
• The nature of the fault.
• The dryer type and model.
• The service code (the number after the word Service on the adhesive rating
plate) on the right-hand side when the door is open.
3
Before using the machine, please also read the instructions for use carefully!
MDC 709T
Programme selector knob
The drying programme is selected by turning this knob.
“Start (Pause)” button
The drying programme is started by pressing this button. The
indicator lamp flashes during the selection phase and lights up
during drying.
Indicator lamps
Filter
The indicator lamp lights up when the filter and/or heat
exchanger need cleaning.
Clean the filter at the end of every cycle.
Water container
The indicator lamp lights up when the water container needs
to be emptied. The drying cycle is automatically interrupted.
Empty the container and restart the drying programme.
Empty the water container after every drying cycle.
Clean heat exchanger
The Led lights up after 30 cycles when the heat exchanger
needs to be cleaned. Clean the heat exchanger. Then for
reset the led indication, turn the programme selector knob
to the vertical position indicated by the symbol “ ” and
press the “Start (Pause)” button during 3 seconds until led
switches off.
Time remaining display
Depending on the programme selected, once the drying
cycle has been started, a default drying time is displayed. The
time displayed is corrected by a few minutes depending on
the volume, type and dampness of the laundry.
The drying time specified is a calculated value which
will be updated during the drying programme.
The flashing lines indicate that the calculation is running. The
remaining time will be updated.
Overdry protection
The indicator lamp lights up when a humidity controlled
program is selected, to indicate the working protection
function. Function is not active in time controlled
programmes 10’, 20’, 30’, 40’, 60’, 90’ and “ ”.
Dryness adjustment
This is an option to adjust the dryness of the laundry according
to your wishes. Select the desired programme and the option
dryness level adjustment by pressing the button “+” for more
dry or the button “-” for more humid. The selected dryness will
be stored as a pre-setting to the selected drying programme.
Using the drying programme next time the pre-setting appears.
By pressing the dryness adjustment buttons “+” or “-” the presetting can be changed.
Quick Reference Guide
Programme sequence
Overdry
protection
Options
Drying
Gentle
Reduces drying intensity (recommended
for delicate items).
Rapid
Shortens drying duration (recommended for thin items of
the same size).
Buzzer
Signals/sounds end of drying cycle.
Anticrease
Prevents laundry from creasing up to 12 hours. The options
“Buzzer” and “Anticrease” cannot be selected together.
Delayed Start (Pause)
Delays the start of the drying cycle by 1 to 12 hours.
Each time the button is pressed, the start time is delayed by
1 hour.
Then press the “Start (Pause)” button to confirm the final
selection and to start the dryer.
The delayed start indicator lamp flashes and the countdown
counts down in 1-hour intervals. The countdown is indicated
by the indicator lamp above the button flashing. During the
countdown, the drum will turn from time to time to redistribute the laundry. To cancel or change the previously set
time delay, set the index of the programme selector knob to
the top, or open the door.
Anti-
crease
GB
End
of cycle
5019 607 00937
(Subject to technical modifications)
4
Loading...