Whirlpool LTG5243DT8, LTG5243DQC, LTG5243DQB, LTG5243DQA, LTG5243DQ9 Installation Guide
...
24"(61CM)GASWASHER RYER INST TION INSTRUCTIONS
_ble ofContents
WASH ER/DRYER SAFETY .............................. 1
iNSTALLATiON iNSTRUCTiONS .................... 2
Tools and Parts .............................................. 2
Alternate Parts ............................................... 3
Location Requirements .................................. 3
Drain System .................................................. 4
Electrical Requirements ................................. 5
Gas Supply Requirements ............................. 5
Venting Requirements .................................... 6
Install Leveling Legs ....................................... 7
WASHER RYER SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kilt or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
Remove Foam Packing .................................. 8
Connect Drain Hose ....................................... 8
Connect Inlet Hoses ...................................... 8
Secure Drain Hose ......................................... 9
Plan Vent System ........................................... 9
Install Vent System ...................................... 11
Level Washer/Dryer ...................................... 11
Make Gas Connection ................................. 11
Connect Vent ............................................... 11
Complete Installation ................................... 12
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
- instructions.
All safety messages wilt tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
WARNING - "Risk of Fire"
- Clothes dryer installation must be performed by a qualified installer.
- Install the clothes dryer according to the manufacturer's instructions and local codes.
- Do not install a clothes dryer with flexible plastic venting materials, if flexible metal
(foil type) duct is installed, it must be of a specific type identified by the appliance
manufacturer as suitable for use with clothes dryers. Flexible venting materials are
known to collapse, be easily crushed, and trap lint. These conditions will obstruct
clothes dryer airflow and increase the risk of fire.
- To reduce the risk of severe injury or death, follow all installation instructions.
- Save these instructions.
IMPORTANT SAFETY INSTRUCTIONS
When discarding or storing your old clothes dryer, remove the door.
SAVE THESE INSTRUCTIONS
W10222384A
WARNING: For your safety, the information in this manual must be followed to minimize
the risk of fire or explosion, or to prevent property damage, personal injury, or death.
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
- WHAT TO DO (F YOU SMELL GAS:
= Do not try to light any appliance.
= Do not touch any electrical switch; do not use any phone in your building.
= Clear the room, building, or area of all occupants.
= (mmediately call your gas supplier from a neighbor's phone. Follow the gas supplier's
instructions.
= if you cannot reach your gas supplier, call the fire department.
- (nstallation and service must be performed by a qualified instal(er, service agency, or
the gas supplier.
WARNING: Gas leaks cannot always be detected by smell.
Gas suppliers recommend that you use a gas detector approved by UL or CSA.
For more information, contact your gas supplier.
If a gas leak is detected, follow the "What to do if you smell gas" instructions.
Inthe State of Massachusetts, the following installation instructions apply:
[] Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by
the State of Massachusetts.
[] If using a ball valve, it shall be a T-handle type.
[] A flexible gas connector, when used, must not exceed 3 feet.
(MPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas
Code, ANSI Z223.1/NFPA 54.
The dryer must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National
Electrical Code, ANSI/NFPA 70.
(NSTAL T(ON (NSTRUCT(ONS
Gather the required tools and parts before starting installation.Read
and follow the instructions provided with any tools listed here.
Parts needed for washer {not provided}:
[] Inlet hoses [] Flat washers
To order: []
[] Call the dealer from whom you purchased your washer/dryer. []
[] Call the toll-free number listed on the cover of the Washer/
Dryer User Instructions.
[] Visit the website listed on the cover of the Washer/Dryer
User Instructions. []
NOTE: Replace inlet hoses after 5 years of use to reduce the risk
of hose failure. Record hose installation or replacement dates for
future reference.
2
Tools needed:
[]
8" or 10" adjustable [] Caulking gun and
wrench (for gas compound (for installing
connections) new exhaust vent)
Flat-blade screwdriver [] Pipe-joint compound
Adjustable wrench that
opens to 1" (25 mm) or [] Level
9/16" (14 mm) open-end
wrench (for adjusting [] Knife
dryer feet) [] Vent clamps
Level [] Pliers
[]
1_,,nut driver or socket [] Wood block (for leveling)
wrench (recommended)
Tin snips (new vent
installation)
resistant to LP gas
[] Ruler or measuring tape
Parts supplied:
Remove parts package from the washer basket. Check that all
parts were included.
A B C D E
A. Rear leveling legs (2)
B. Front leveling legs (2)
C. Drain hose
D. Plastic strap
E. Silver double-wire hose clamp
Parts needed:
Check local codes and with gas supplier, check existing gas
supply, electrical supply and venting, and read "Electrical
Requirements," "Gas Supply Requirements," and "Venting
Requirements" before purchasing parts.
Mobile home installations require special parts (listed following)
available for purchase from the dealer from whom you purchased
your dryer. For further information, please reference the
"Assistance or Service" section of the Washer/Dryer User
Instructions.
[] Mobile Home Installation Kit. Ask for Part Number 346764.
[] Metal exhaust system hardware.
Your installation may require additional parts. For information on
ordering, please refer to the toll free phone numbers on the front
page of the Washer/Dryer User Instructions.
If You Have You Will Need to Buy
Laundry tub or Sump pump system (if not already
standpipe taller than available)
96" (2.4 m)
1" (25 mm) diameter 2" (51 mm) diameter to 1" (25 mm)
standpipe diameter standpipe adapter, Part
Number 3363920
Overhead sewer
Standard 20 gal. (76 L) 34" (864 mm)
tall drain tub or utility sink and sump
pump (available from local plumbing
suppliers)
Floor drain Siphon break, Part Number 285320,
additional drain hose, Part Number
285702 and connector kit,
Part Number 285442
Drain hose too short Drain hose, Part Number 285664 and
connector kit, Part Number 285442
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from dryer.
Failure to do so can result in death, explosion, or fire.
You will need
[] A location that allows for proper exhaust installation. A gas
washer/dryer must be exhausted to the outdoors. See
"Venting Requirements."
[]
A grounded electrical outlet located within 2 ft (610 mm) of
either side of the washer/dryer. See "Electrical Requirements."
[]
A sturdy floor to support the washer/dryer weight (washer/
dryer, water and load) of 500 Ibs (226.8 kg).
[]
A level floor with a maximum slope of 1" (25 mm) under entire
washer/dryer. Clothes may not tumble properly and automatic
sensor cycles may not operate correctly if washer/dryer is not
level. Installing on carpet is not recommended.
[]
A water heater set to deliver 120°F (49°C) water to the washer.
[]
Hot and cold water faucets located within 4 ft (1.2 m) of the
hot and cold water fill valves, and water pressure of 5-100 psi
(34.5-689.6 kPa).
The washer/dryer must not be installed or stored in an area where
it will be exposed to water and/or weather.
Do not operate your washer in temperatures at or below
32°F (0°C). Some water can remain in the washer and can cause
damage in low temperatures. See "Washer/Dryer Care" in the
Washer/Dryer User Instructions for winterizing information.
Do not operate your dryer at temperatures below 45°F (7°C). At
lower temperatures, the dryer might not shut off at the end of an
automatic cycle. This can result in longer drying times.
Check code requirements. Some codes limit, or do not permit,
installation of the washer/dryer in garages, closets, mobile homes,
or sleeping quarters. Contact your local building inspector.
NOTE: No other fuel-burning appliance can be installed in the
same closet as a dryer.
Installation Clearances
The location must be large enough to allow the dryer door
to open fully.
Lint clogged drain Drain protector, Part Number 367031
Water faucets 2 longer water fill hoses:
beyond reach of fill 6 ft (1.8 m) Part Number 76314,
hoses 10 ft (3.0 m) Part Number 350008
Washer/Dryer Dimensions
713/4"
(1822 ram)
153/8"
(391rnrn)
Mobile home installations require:
[] Metal exhaust system hardware, which is available for
purchase from your dealer.
[] Mobile Home Installation Kit Part Number 346764. See "Tools
and Parts" section for information on ordering.
Special provisions must be made in mobile homes to
introduce outside air into the dryer. The opening (such as a
nearby window) should be at least twice as large as the dryer
exhaust opening.
The washer/dryer can be installed using the standpipe drain
system (floor or wall), the laundry tub drain system, or the floor
drain system. Select the drain hose installation method you need.
See "Alternate Parts."
*271A"
(692 ram) 237/8"
(606 ram)
*Most installations require a minimum 5" (127 mm) clearance
behind the dryer for the exhaust vent with elbow. See "Venting
Requirements."
Installation spacing for recessed area or closet installation
The following spacing dimensions are recommended for this
washer/dryer. This washer/dryer has been tested for spacing of 0"
(0 mm) clearance on the sides, rear and top. Recommended
spacing should be considered for the following reasons:
[] Additional spacing should be considered for ease of
installation and servicing.
[]
Additional clearances might be required for wall, door,
and floor moldings.
[]
Additional spacing on all sides of the washer/dryer is
recommended to reduce noise transfer.
[]
For closet installation, with a door, minimum ventilation
openings in the top and bottom of the door are required.
Louvered doors with equivalent ventilation openings are
acceptable.
(25mm)
48in,2 =
1310cm2)
o oo o_.................._2o
24i&2 -4
m
1"_41_-23'J,"_11_1"
(25ram) (606mm) (25rnra}
A
A. Recessed area
B. Side view - closet or confined area
C. Closet door with vents
-_ 1"* I_- 27_"-_
(25ram)(692mm)
B
155cm2)
_- 5"**
(127mm)
C
Standpipe drain system - wall or floor (views A & B}
The standpipe drain requires a minimum diameter standpipe of
2" (51 mm). The minimum carry-away capacity can be no less than
17 gal. (64 L) per minute. A 2" (51 mm) diameter to 1" (25 mm)
diameter standpipe adapter kit is available. See "Alternate Parts."
The top of the standpipe must be at least 39" (991 mm) high and no
higher than 96" (2.4 m) from the bottom of the washer.
A
B
Laundry tub drain system (view C)
The laundry tub needs a minimum 20 gal. (76 L) capacity. The top
of the laundry tub must be at least 34" (864 ram) above the floor
and no higher than 96" (2.4 m) from the bottom of the washer.
Floor drain system (view D)
The floor drain system requires a siphon break that may be
purchased separately. See "Alternate Parts."
The siphon break must be a minimum of 28" (711 ram) from the
bottom of the washer. Additional hoses might be needed.
*Required spacing
**Rear clearance may be 0" (0 mm) when house exhaust system
is lined up directly with dryer exhaust.
Mobile Home =Additional Installation Requirements
This washer/dryer is suitable for mobile home installations.
The installation must conform to the Manufactured Home
Construction and Safety Standard, Title 24 CFR, Part 3280
(formerly the Federal Standard for Mobile Home Construction
and Safety, Title 24, HUD Part 280).
4
C D
Loading...