Whirlpool LPR 828, LPR 827/01, G2P 70F WH, LPR 828/01, G2P 70F/SS INSTRUCTION FOR USE

6gb66028a.fm Page 3 Friday, August 20, 2004 10:51 AM

INSTRUCTIONS FOR USE

INSTALLATION ELECTRICAL CONNECTION BEFORE USING THE OVEN

SAFEGUARDING THE ENVIRONMENT

PRECAUTIONS AND GENERAL RECOMMENDATIONS

OVEN ACCESSORIES

CARE AND CLEANING TROUBLE-SHOOTING GUIDE AFTER SALES SERVICE DECLARATION OF CONFORMITY CE

3

6gb66028a.fm Page 4 Friday, August 20, 2004 10:51 AM

INSTALLATION

Technical information for the installer

•The oven has been designed to be installed under a worktop surface.

•Do not lift the oven by the handle, but hold it by the sides.

•Make sure that the appliance was not damaged during transport.

•The oven and unit dimensions are shown in the below figures.

•The units in contact with the oven must be heat-resistant (min. 85°C).

•If the plastic laminates or the sealing material are not sufficiently heat resistant, this may result in the formation of bubbles, deformation of the surface or detachment of the coating.

•Insert the oven in the unit cavity, lifting it by the sides and being careful not to trap the power cable.

•The oven and housing dimensions are illustrated in the below figures.

•For correct ventilation, follow the ventilation opening directions shown in the figure 1.

•Two systems can be used to fit your appliance to a chosen furniture layout:

A.Between two side panels of two distinct cabinet units without the aid of a support shelf, by fitting four support steel brackets provided with the product. (fig. 3).

B.Between two side panels each fixed to the side of a cabinet unit without the aid of a support shelf. In this case only

the two lower support brackets will be necessary (fig. 4).

Note: In both of the above cases you must measure 717 mm from the underside of the worktop and mark the correct position of the lower support brackets before fixing them to the sides. With reference to (fig. 3), ensure the side support brackets are positioned 40 mm from the front of the cabinet door exterior surface, as illustrated, before securing them to the cabinet sides. If necessary, this product can be installed in a housing unit (fig. 2). The housing unit will not be a standard one but will have to be of a size that can accommodate the full height of the oven - minimum height 717 mm. This housing unit will need to fulfil the ventilation requirements.

• Fasten the oven using the screws.

											Top
NOTE:							Rear						Front of
							Wall				Oven
Always		remove											oven
the	rear panel
of	the	housing
unit
														Important
Fig. 1													BACK EDGE OF SUPPORT
												SHELF (WHEN APPLICABLE)
			0			Mi
						n
		0					.
		6					5
								6
									0
				717
							E
						ID
						S							5
													4
														5
													2
												8	5	2
												4	9
												5	5
										4	665			715
										0
				E		S						708
				N	R
				N
			U
			R
											5
											2
Fig. 3												5

	5
	6
-5
2
6
5

				M															5
						i													4
						n.														5
							5
								6
										0			717						2
																	8		5	2
																	4
																	5	9
																		5
														665			708			715
															5
Fig. 2															2
																5
			5			Mi
		6						n
	5								.
	-									5
2											6
6												0
5
					717
																			5
																			4
																				5
																			2
																	8		5	2
																	4	9
																	5	5
													4	665						715
													0
				N		S											708
					R
				E
				N
			U
			R
															5
																2
Fig. 4																	5

4