WHIRLPOOL LAB0050P User Manual
PEDESTAL INSTALLATION INSTRUCTIONS
For use with Model LAB0050PQ
INSTRUCTIONS D'INSTALLATION DU PIÉDESTAL
Pour utilisation avec le modèle LAB0050PQ
Table of Contents / Table des matières
PEDESTAL SAFETY .......................................................................1
INSTALLATION REQUIREMENTS................................................2
Tools and Parts ............................................................................2
Location Requirements................................................................2
Before Installing Your Pedestal.................................................... 2
INSTALLATION INSTRUCTIONS..................................................3
Install Pedestal .............................................................................3
21¹⁄₄"
(53.97 cm)
12"
(30.48 cm)
SÉCURITÉ DU PIÉDESTAL...........................................................4
EXIGENCES D'INSTALLATION.....................................................4
Outillage et pièces........................................................................4
Exigences d'emplacement...........................................................4
Avant l'installation du piédestal ...................................................5
INSTRUCTIONS D'INSTALLATION .............................................. 5
Installation du piédestal...............................................................5
23
¹⁄₂
"
(59.69 cm)
PEDESTAL SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
You can be killed or seriously injured if you don't immediately
DANGER
WARNING
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
8578919A
follow instructions.
can be killed or seriously injured if you don't
You
instructions.
follow
INSTALLATION REQUIREMENTS
Tools and Parts
Check that you have everything necessary for correct installation.
Too ls Requi red
■ ⁷⁄₁₆" (11 mm) wrench (for bracket self-locking nut)
■ ⁹⁄₁₆" (14 mm) open-ended wrench (for foot locknut)
■ Level
Parts Supplied
Remove parts from package. Check that all parts were included.
B
A
E
A. Metal pedestal
B. Mounting brackets (4)
C.Carriage bolts (4)
D. Self-locking nuts (4)
E. Feet with rubber caps (4)
F. Locknuts (4)
C
D
F
Location Requirements
Before Installing Your Pedestal
IMPORTANT: If your washer and dryer are already installed, they
must be uninstalled.
If you need to uninstall your washer or dryer, see the Installation
Instructions that came with your model for tools required.
Uninstalling Your Washer
WARNING
Excessive Weight Hazard
Use two or more people to move and uninstall washer.
Failure to do so can result in back or other injury.
1. Unplug the power supply cord.
2. Turn off the hot and cold water faucets.
3. Slowly loosen the fill hoses at the faucets to relieve the water
pressure. Use a sponge or towel to absorb the released
water.
4. Pull the washer away from the wall so the pedestal can be
placed in its final location.
Uninstalling Your Electric Dryer
WARNING
Excessive Weight Hazard
Use two or more people to move and uninstall dryer.
Failure to do so can result in back or other injury.
WARNING
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from dryer.
Place dryer at least 18 inches (46 cm) above the floor
for a garage installation.
Failure to do so can result in death, explosion, or fire.
If dryer and pedestal assembly is located in a garage, 6" (15.2 cm)
must be added under pedestal so that the dryer is 18" (46 cm)
above garage floor. A separate riser, able to support at least
275 lbs 124.7 kg), may be required. The entire pedestal must sit
completely on the riser.
1. Unplug dryer or disconnect power.
2. Pull the dryer away from the wall enough to loosen the vent
clamp. Loosen the clamp and slowly remove the exhaust vent
from the dryer exhaust outlet.
3. Pull the dryer away from the wall so the pedestal can be
placed in its final location.
2
Loading...