Whirlpool KTRP22EMWH00, KTRA22EMSS03, KTRA22EMWH03, KTLA22EMSS01, KTRA19EMBT01 User Manual

...
SIDE BY SIDE REFRIGERATOR
Use & Care Guide
For questions about features, operation/performance parts, accessories or service, call: 1-800-253-1301.
In Canada, call for assistance 1-800-461-5681, for installation and service, call: 1-800-807-6777
www.whirlpool.com or www.whirlpool.com/canada
or visit our website at...
RÉFRIGÉRATEUR CÔTE À CÔTE
Guide d’utilisation et d’entretien
ou visitez notre site web à
www.whirlpool.com/canada
Table of Contents/Table des matières .......................................2
2255705
TABLE OF CONTENTS
TABLE DES MATIÈRES
REFRIGERATOR SAFETY .............................................................3
Proper Disposal of Your Old Refrigerator....................................3
INSTALLATION INSTRUCTIONS..................................................4
Unpacking ....................................................................................4
Location Requirements................................................................4
Electrical Requirements ...............................................................5
Base Grille ....................................................................................5
Door Removal............................................................................... 6
Door Closing.................................................................................8
Water Supply Connection............................................................ 8
Water System Preparation........................................................... 9
Normal Sounds ..........................................................................10
REFRIGERATOR USE ..................................................................10
Ensuring Proper Air Circulation..................................................10
Using the Controls .....................................................................10
Water and Ice Dispensers..........................................................11
Water Filter Status Light.............................................................12
Water Filtration System..............................................................13
Ice Maker and Storage Bin/Bucket............................................13
REFRIGERATOR FEATURES ......................................................14
Refrigerator Shelves...................................................................15
Flip-up Shelf ...............................................................................15
Adjustable Flip-up Shelf.............................................................15
Drop-down shelf.........................................................................15
Deli Drawer.................................................................................15
Convertible Vegetable/Meat Drawer, Crisper and Covers ........16
Convertible Vegetable/Meat Drawer Temperature Control.......16
Crisper Humidity Control ...........................................................16
Wine or Can/Bottle Rack ...........................................................16
Utility Bin ....................................................................................17
FREEZER FEATURES..................................................................17
Freezer Shelf ..............................................................................17
Freezer Basket or Bin.................................................................17
DOOR FEATURES........................................................................17
Tilt-out Freezer Door Bin............................................................17
Chilled Door Bin .........................................................................17
Door Rails...................................................................................18
Door Bins....................................................................................18
REFRIGERATOR CARE ...............................................................18
Cleaning......................................................................................18
Changing the Light Bulbs...........................................................19
Power Interruptions....................................................................20
Vacation and Moving Care.........................................................20
TROUBLESHOOTING ..................................................................21
ASSISTANCE OR SERVICE.........................................................23
In the U.S.A. ...............................................................................23
In Canada ...................................................................................24
Accessories................................................................................24
WATER FILTER CERTIFICATIONS.............................................24
PRODUCT DATA SHEETS...........................................................25
WARRANTY ..................................................................................27
SÉCURITÉ DU RÉFRIGÉRATEUR ..............................................28
Mise au rebut de votre vieux réfrigérateur.................................28
INSTRUCTIONS D’INSTALLATION.............................................29
Déballage....................................................................................29
Emplacement dinstallation ........................................................29
Spécifications électriques ..........................................................30
Grille de la base..........................................................................30
Enlèvement des portes...............................................................31
Fermeture des portes.................................................................33
Raccordement de la canalisation d'eau ....................................33
Préparation du système deau...................................................34
Sons normaux ............................................................................35
UTILISATION DU RÉFRIGÉRATEUR..........................................35
Pour sassurer dune circulation dair appropriée......................35
Utilisation des commandes........................................................35
Distributeurs deau et de glaçons ..............................................36
Le témoin lumineux de l’état du filtre à eau...............................38
Système de filtration deau ........................................................38
Machine à glaçons et bac/seau dentreposage ........................39
CARACTÉRISTIQUES DU RÉFRIGÉRATEUR ...........................40
Tablettes du réfrigérateur ...........................................................41
Tablette relevable .......................................................................41
Tablette relevable ajustable .......................................................41
Étagère inclinable.......................................................................41
Tiroir pour spécialités alimentaires ............................................42
Tiroir à légumes/viande convertible,
bac à légumes et couvercles .....................................................42
Réglagedelatempérature du tiroir à
légumes/viande convertible .......................................................42
Réglagedel’humidité dans le bac à légumes...........................43
Casier à vin ou porte-cannettes/bouteilles ................................43
Casier utilitaire............................................................................43
CARACTÉRISTIQUES DU CONGÉLATEUR...............................43
Tablette de congélateur .............................................................43
Panieroubacdecongélateur....................................................44
CARACTÉRISTIQUES DE LA PORTE.........................................44
Compartiment inclinable de la porte du congéalateur ..............44
Compartiment fraîcheur .............................................................44
Tringles dans la porte.................................................................45
Balconnets dans la porte ...........................................................45
ENTRETIEN DU RÉFRIGÉRATEUR ............................................45
Nettoyage ...................................................................................45
Remplacement des ampoules d’éclairage ................................46
Pannes de courant .....................................................................47
Entretien avant les vacances ou lors dun déménagement.......48
DÉPANNAGE.................................................................................48
ASSISTANCE OU SERVICE.........................................................52
Accessoires ................................................................................52
FEUILLES DE DONNÉES SUR LE PRODUIT.............................53
GARANTIE.....................................................................................55
®
2
REFRIGERATOR SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.
This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or
“WARNING.” These words mean:
You can be killed or seriously injured if you don't immediately follow instructions.
can be killed or seriously injured if you don't
You follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
WARNING:To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic
precautions:
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Disconnect power before servicing.
Replace all panels before operating.
Remove doors from your old refrigerator.
happen if the instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
Use nonflammable cleaner.
Keep flammable materials and vapors, such as
gasoline, away from refrigerator.
Use two or more people to move and install
refrigerator.
Disconnect power before installing ice maker (on
ice maker kit ready models only).
Use a sturdy glass when dispensing ice or water (on some models).
SAVE THESE INSTRUCTIONS
Proper Disposal of Your Old Refrigerator
WARNING
Suffocation Hazard Remove doors from your old refrigerator. Failure to do so can result in death or
brain damage.
IMPORTANT: Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous – even if they will sit for just a few days.If you are getting rid of your old refrigerator, please follow these instructions to help prevent accidents.
Before you throw away your old refrigerator or freezer:
Take off the doors.
Leave the shelves in place so that children may not easily climb inside.
3
INSTALLATION
Location Requirements
INSTRUCTIONS
Unpacking
WARNING
Excessive Weight Hazard
Use two or more people to move and install refrigerator.
Failure to do so can result in back or other injury.
Removing packaging materials
Remove tape and glue residue from surfaces before turning on the refrigerator. Rub a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry.
Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your refrigerator. For more information, see the “Refrigerator Safety” section.
When MovingYour Refrigerator:
Your refrigerator is heavy. When moving the refrigerator for cleaning or service, be sure to protect the floor. Always pull the refrigerator straight out when moving it. Do not wiggle or walkthe refrigerator when trying to move it, as floor damage could occur.
Cleaning before use
After you remove all of the packaging materials, clean the inside of your refrigerator before using it. See the cleaning instructions in the “Refrigerator Care” section.
WARNING
Explosion Hazard
Keep flammable materials and vapors, such as gasoline, away from refrigerator.
Failure to do so can result in death, explosion, or fire.
To ensure proper ventilation for your refrigerator, allow for ¹⁄₂ in. (1.25 cm) space on each side and at the top. When installing your refrigerator next to a fixed wall, leave 2 in. (5.08 cm) minimum on each side (depending on your model) to allow for the door to swing open. If your refrigerator has an ice maker, allow extra space at the back for the water line connections.
NOTE: Do not install the refrigerator near an oven, radiator, or other heat source, nor in a location where the temperature will fall below 55°F (13°C).
1
/
2
" (1.25 cm)
Important information to know about glass shelves and covers:
Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. For your protection, tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use special care when re­moving them to avoid impact from dropping.
4
2" (5.08 cm)
Electrical Requirements
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in
death, fire, or electrical shock.
Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical connection:
Base Grille
To remove the base grille:
1. Open both doors.
2. Place hands along the ends of the grille, with your thumbs
along the top. Push in with your thumbs and pull up on the bottom.
NOTE: Be sure to refasten the Tech Sheet behind the base grille after cleaning.
To replace the base grille:
1. Open both doors.
2. Line up the grille support tabs with the metal clips.
3. Push the grille firmly to snap it into place.
Recommended grounding method
A 115 Volt, 60 Hz., AC only 15 or 20 ampere fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an extension cord.
NOTE: Before performing any type of installation, cleaning, or removing a light bulb, turn the control (Thermostat, Refrigerator or Freezer Control depending on the model) to OFF and then disconnect the refrigerator from the electrical source. When you are finished, reconnect the refrigerator to the electrical source and reset the control (Thermostat, Refrigerator or Freezer Control depending on the model) to the desired setting.
5
Door Removal
TOOLS NEEDED: ¹⁄₄ IMPORTANT: Before you begin, turn the refrigerator control OFF. Unplug refrigerator or disconnect power. Remove food and any
adjustable door or utility bins from doors. NOTE: It may only be necessary to remove either the door handle or the doors to get your product through the doorway of your home.
Measure the door opening to see whether you need to remove the refrigerator handles or the doors.
in. hex-head socket wrench,
Disconnect power before removing doors.
Reconnect both ground wires before operating.
Failure to do so can result in death or electrical shock.
⁵⁄₁₆
in. hex-head socket wrench and a flat-blade screwdriver.
Electrical Shock Hazard
4
Top Left Hinge
Style 1
1
Style 2
1
1. Do Not Remove Screw
3
Water Dispenser Tubing Connection
5
Door Removal
6
Top Right Hinge
1
1. Do Not Remove Screw
1
Style 1 Handle Removal (Optional)
1
Style 2 Handle Removal (Optional)
1. Red Outer Ring
2
Base Grille
6
1
8
Door Alignment
1
1. Leveling Screw
7
Bottom Hinge
1
1. Do Not Remove Screw
Handle Removal (optional)
3
Style 1
1. Apply firm pressure with your hand on the face of trim. Slide
top trim up and bottom trim down away from handle. Lift trim pieces off shoulder screws (see Graphic 1).
NOTE: Some models include accent pieces between the handle and the handle trim. If your model includes the accents, you will need to carefully remove them with a flat-blade screwdriver before removing the handle screws. The accent pieces are optional and can be reinstalled or left off the handle assembly.
2. Remove handle screws and handles. (See Graphic 1)
3. Move refrigerator into place. Replace handles as shown (see
Graphic 1).
Style 2
1. Apply firm pressure on the handle to slide it up and off of the
shoulder screws (see Graphic 1).
2. Move refrigerator into place. Replace handles as shown (see
Graphic 1).
Door Removal
6. Disconnect wiring:
Style 1
Disconnect wiring plug.
Remove green ground wire screw to disconnect ground wires.
1
2
1. Do not remove screw 1.
2. Ground wires
3. Green ground wire screw
Style 2
Disconnect wiring plug.
1
2
WARNING
Electrical Shock Hazard
Disconnect power before removing doors. Failure to do so can result in death or
electrical shock.
1. Unplug refrigerator or disconnect power.
2. Open both refrigerator doors. Remove the base grille by
pulling up on the bottom outside corners (see Graphic 2).
3. Close both doors and keep them closed until you are ready to
lift them free from the cabinet.
4. If you have a dispenser (ice or water), disconnect the water
dispenser tubing located behind the base grille on the freezer door side (see Graphic 3).
Press the red outer ring against the face of the fitting and pull the dispenser tubing free.
On some models, remove the tubing from the hose clip.
5. Remove the top left hinge cover and screws as shown (see
Graphic 4). Do not remove screw 1.
1. Do not remove screw 1.
2. Wiring plug
7. Carefully lift the freezer door straight up and off of the bottom
hinge (see Graphic 5). The water dispenser tubing remains attached to the freezer door and pulls through the bottom left hinge. Make sure you protect the dispenser tubing from damage.
8. Remove the top right hinge cover and screws as shown (see
Graphic 6). Do not remove screw 1.
9. Lift the refrigerator door straight up and off of the bottom
hinge.
10. It may not be necessary to remove the bottom hinge to move
the refrigerator through a doorway. Both bottom hinges have similar construction. If necessary, disassemble the hinges as shown (see Graphic 7). Do not remove screw 1.
Door and Hinge Replacement
1. Replace both bottom hinges, if removed. Tighten screws.
2. Assistance may be needed to feed the water dispenser
tubing through the bottom hinge while reinstalling the freezer door. Carefully feed the dispenser tubing through the bottom left hinge before replacing the door on the hinge.
NOTE: Provide additional support for the doors while the top hinges are being replaced. Do not depend on the door magnets to hold the doors in place while you are working.
3. Reconnect water dispenser tubing by pushing tubing into
fitting until it stops and black mark touches face of fitting (see Graphic 3). On some models, replace tubing in hose clip.
7
4. Align and replace the top left hinge as shown (see Graphic 4).
3
Tighten screws.
WARNING
Electrical Shock Hazard
Reconnect both ground wires.
Failure to do so can result in death or electrical shock.
Style 1
Reconnect both ground wires.
Reconnect wiring plug.
1
Door Closing
Your refrigerator has two front adjustable rollers one on the right and one on the left. If your refrigerator seems unsteady or if you want the doors to close more easily, adjust the refrigerator's tilt using the instructions below:
1. Move the refrigerator into its final position.
2. The two leveling screws are part of the front roller assemblies,
which are at the base of the refrigerator on either side (see Graphic 8).
3. Use a hex-head socket wrench to adjust the leveling screws.
Turn the leveling screw to the right to raise that side of the refrigerator or turn the leveling screw to the left to lower that side. It may take several turns of the leveling screws to adjust the tilt of the refrigerator (see Graphic 8).
NOTE: Having someone push against the top of the refrigerator takes some weight off the leveling screws and rollers. This makes it easier to adjust the screws.
4. Open both doors again and check to make sure that they
close as easily as you like. If not, tilt the refrigerator slightly more to the rear by turning both leveling screws to the right. It may take several more turns, and you should turn both leveling screws the same amount.
5. Replace the base grille. NOTE: Be sure to refasten the Tech Sheet behind the base grille.
2
1. Do not remove screw 1.
3. Green ground wire screw
2. Ground wires
Style 2
Reconnect wiring plug.
1
1. Do not remove screw 1.
2. Wiring plug
5. Replace left hinge cover and screws.
6. Replace the refrigerator door by carefully lifting the door onto
the bottom right hinge.
7. Align and replace the top right hinge as shown (see
Graphic 6). Tighten screws.
8. Replace hinge cover and screws. Tighten screws.
9. Plug into a grounded 3 prong outlet.
2
Water Supply Connection
Read all directions carefully before you begin.
IMPORTANT:
If you turn the refrigerator on before the water line is connected, turn the ice maker OFF.
All installations must meet local plumbing code requirements.
Use copper tubing and check for leaks. Install copper tubing only in areas where the household temperatures will remain above freezing.
Tools required: Flat-blade screwdriver, ⁷⁄₁₆ in. and ¹⁄₂ in. open-end wrenches or two adjustable wrenches, ¹⁄₄ in. nut driver and drill bit, hand drill or electric drill (properly grounded).
NOTE: Your refrigerator dealer has a kit available with a ¹⁄₄ in. (6.35 mm) saddle-type shutoff valve, a union, and copper tubing. Beforepurchasing,makesureasaddle-typevalvecomplieswith your local plumbing codes. Do not use a piercing-type or ³⁄₁₆ in. (4.76 mm) saddle valve which reduces water flow and clogs more easily.
Cold water supply
Connect the ice maker to a cold water line with water pressure between 30 and 120 psi (207-827 kPa). If you have questions about your water pressure, call your utility company.
Connecting to Water Line
1. Unplug refrigerator or disconnect power.
2. Turn OFF main water supply. Turn ON nearest faucet long
enough to clear line of water.
3. Locate a ½ in. to 1¹⁄₄ in. (1.25 cm to 3.18 cm) vertical COLD
water pipe near the refrigerator. NOTE: Horizontal pipe will work, but drill on the top side of
the pipe, not the bottom. This will help keep water away from the drill and normal sediment from collecting in the valve.
8
4. Determine the length of copper tubing you need. Measure
from the connection on the lower left rear of refrigerator to the water pipe. Add 7 ft. (2.1 m) to allow for cleaning. Use ¹⁄₄ in. (6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.
5. Using a grounded drill, drill a ¹⁄₄ in. hole in the cold water pipe
you have selected.
Water System Preparation
Please read before using the water system. Immediately after installation, follow the steps below to make
sure that the water system is properly cleaned.
1. Open the freezer door and turn off the ice maker. For Style 1 lift up the wire shutoff arm as shown. For Style 2 move the switch to the OFF (right) setting as shown. The ON/OFF switch is located on the top right side of the freezer compartment.
Style 1
1. Cold Water Pipe
2. Pipe Clamp
3. Copper Tubing
4. Compression Nut
5. Compression Sleeve
6. Shutoff Valve
7. Packing Nut
6. Fasten the shutoff valve to the cold water pipe with the pipe
clamp. Be sure the outlet end is solidly in the ¹⁄₄ in. drilled hole in the water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp screws carefully and evenly so washer makes a watertight seal. Do not overtighten or you may crush the copper tubing.
7. Slip the compression sleeve and compression nut on the
copper tubing as shown. Insert the end of the tubing into the outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten.
8. Place the free end of the tubing in a container or sink, and
turn ON the main water supply. Flush the tubing until water is clear. Turn OFF the shutoff valve on the water pipe. Coil the copper tubing.
Connecting to Refrigerator
1. Attach the copper tube to the valve inlet using a compression
nut and sleeve as shown. Tighten the compression nut. Do not overtighten. Use the tube clamp on the back of the refrigerator to secure the tubing to the refrigerator as shown. This will help prevent damage to the tubing when the refrigerator is pushed back against the wall.
2. Turn shutoff valve ON.
3. Check for leaks. Tighten any connections (including
connections at the valve) or nuts that leak.
1. Tube Clamp
2. Copper Tubing
4. The ice maker is equipped with a built-in water strainer. If
your water conditions require a second water strainer, install it in the ¹⁄₄ in. (6.35 mm) water line at either tube connection. Obtain a water strainer from your nearest appliance dealer.
5. Plug in refrigerator or reconnect power.
3. Compression Nut
4. Valve Inlet
Style 2
NOTES:
If your model has a base grille filter system, make sure the base grille filter is properly installed and the cap is in the horizontal position.
Do not use with water that is microbiologically unsafe or
■■■■
of unknown quality without adequate disinfection before or after the system.
2. Use a sturdy container to depress the water dispenser bar
until the water begins to flow. Flush the water system by dispensing and discarding 2 to 3 gal. (8 to 12 L) of water. Cleaning the system will take approximately 6 to 7 minutes and will help clear air from the line. Additional flushing may be required in some households.
NOTE: As air is cleared from the system, water may spurt out of the dispenser.
3. Open the freezer door and turn on the ice maker. For Style 1 lower the wire shutoff arm. For Style 2 move the switch to the ON (left) position. Please refer to the Ice Maker and Storage Bin/Bucketsection for further instructions on the operation of your ice maker.
Allow 24 hours to produce the first batch of ice.
Discard the first three batches of ice produced.
Depending on your model, you may want to select the maximum ice feature to increase the production of ice.
9
NormalSounds
Your new refrigerator may make sounds that your old one didn’t make. Because the sounds are new to you, you might be concerned about them. Most of the new sounds are normal. Hard surfaces, such as the floor, walls, and cabinets, can make the sounds seem louder. The following describes the kinds of sounds and what may be making them.
If your product is equipped with an ice maker, you will hear a buzzing sound when the water valve opens to fill the ice maker for each cycle.
Your refrigerator is designed to run more efficiently to keep your food items at the desired temperatures and to minimize energy usage. The high efficiency compressor and fans may cause your refrigerator to run longer than your old one. You may also hear a pulsating or high-pitched sound from the compressor or fans adjusting to optimize performance.
You may hear the evaporator fan motor circulating air through the refrigerator and freezer compartments. The fan speed may increase as you open the doors or add warm food.
Rattling noises may come from the flow of refrigerant, the water line, or items stored on top of the refrigerator.
Water dripping on the defrost heater during a defrost cycle may cause a sizzling sound.
As each cycle ends, you may hear a gurgling sound due to the refrigerant flowing in your refrigerator.
Contraction and expansion of the inside walls may cause a popping noise.
You may hear air being forced over the condenser by the condenser fan.
You may hear water running into the drain pan during the defrost cycle.
REFRIGERATOR USE
Ensuring Proper Air Circulation
In order to ensure proper temperatures, you need to permit air to flow between the two sections. Cold air enters the bottom of the freezer section and moves up. It then enters the refrigerator section through the top vent. Air then returns to the freezer as shown.
IMPORTANT: Because air circulates between both sections, any odors formed in one section will transfer to the other. You must thoroughly clean both sections to eliminate odors. To prevent odor transfer from food, wrap or cover foods tightly.
Using the Controls
For your convenience, your refrigerator controls are preset at the factory. When installing your refrigerator, make sure that the controls are still preset to the mid-settingsas shown.
Style 1
Style 2
IMPORTANT:
Your product will not cool when the Refrigerator Control is set to OFF.
The Refrigerator Control adjusts the refrigerator compartment temperature. The Freezer Control adjusts the freezer compartment temperature. Higher numbered settings make the compartment colder. Lower numbered settings make the temperature less cold.
Wait 24 hours before you put food into the refrigerator. If you add food before the refrigerator has cooled completely, your food may spoil.
NOTE: Adjusting the Refrigerator and Freezer Controls to a higher (colder) setting will not cool the compartments any faster.
The preset settings should be correct for normal household usage. The controls are set correctly when milk or juice is as cold as you like and when ice cream is firm.
If the temperature is too warm or too cold in the refrigerator or freezer,firstchecktheairventstobesuretheyarenot blocked before adjusting the controls.
Do not block any of these vents with food such as soda, cereal, bread, etc. If the vents are blocked, airflow will be prevented and the temperature controls will not function properly.
10
Adjusting the Controls
If you need to adjust temperatures, adjust the refrigerator temperature first.
NOTE: Wait at least 24 hours between adjustments and then recheck the temperatures.
Style 1
Turn the control to the right (clockwise) to make the compartment colder or to the left (counterclockwise) to make it less cold.
Style 2
1. Push in on the control and release it.
2. The control will pop out. Turn the control to the desired
setting.
3. Push the control in to lock it in place. CONDITION/REASON: SETTING
ADJUSTMENT:
REFRIGERATOR too cold
Not set correctly for your conditions
REFRIGERATOR Control one setting lower
Some models dispense both cubed and crushed ice. Before dispensing ice, select which type of ice you prefer. The button controls are designed for easy use and cleaning.
Style 1 Style 2
ICE
CRUSH CUBE
REFRIGERATOR too warm
Door opened often, large amount of food added or room temperature very warm
FREEZER too cold
Not set correctly for your conditions
FREEZER too warm/too little ice
Door opened often, or large amount of food added or very cold room temperature (cantcycleoften enough) or heavy ice usage
Water and Ice Dispensers
(on somemodels)
WARNING
REFRIGERATOR Control one setting higher
FREEZER Control one setting lower
FREEZER Control one setting higher
For crushed ice, cubes are crushed before they are dispensed. This may cause a slight delay when dispensing crushed ice. Noise from the ice crusher is normal, and pieces of ice may vary in size. When changing from crushed to cubed, a few ounces of crushed ice will be dispensed along with the first cubes.
To dispense ice:
1. Press button for the desired type of ice.
2. Press a sturdy glass against the ice dispenser lever. Hold the
glass close to the dispenser opening so ice does not fall outside of the glass.
IMPORTANT: You do not need to apply a lot of pressure to the lever in order to activate the ice dispenser. Pressing hard will not make the ice dispense faster or in greater quantities.
3. Remove the glass to stop dispensing. NOTE: The first few batches of ice may have an off-flavor
from new plumbing and parts. Throw the ice away. Also, take large amounts of ice from the ice bin, not through the dispenser.
The water dispenser
Cut Hazard
Use a sturdy glass when dispensing ice or water.
Failure to do so can result in cuts.
Depending on your model, you may have one or more of the following options: the ability to select either crushed or cubed ice, a special light that turns on when you use the dispenser, a special Night Light mode, or a lock option to avoid accidental dispensing.
The ice dispenser
Ice dispenses from the ice maker storage bin in the freezer. When the dispenser lever is pressed:
A trap door opens in a chute between the dispenser and the ice bin. Ice moves from the bin and falls through the chute.
When you release the dispenser lever, the trap door closes and the ice dispensing stops. The dispensing system will not operate when the freezer door is open.
If you did not flush the water system when the refrigerator was first installed, press the water dispenser bar with a glass or jar until you draw and discard 2 to 3 gal. (8 to 12 L) or approximately 6 to 7 minutes of water after water begins dispensing. It will take 3 to 4 minutes for the water to begin dispensing. The water you draw and discard cleans the system and helps clear air from the lines. Allow several hours for the refrigerator to cool down and chill water.
IMPORTANT: Depending on your model, the small removable tray at the bottom of the dispenser is designed to catch small spills and allow for easy cleaning. There is no drain in the tray. The tray can be removed from the dispenser and carried to the sink to be emptied or cleaned.
11
To d i s p e n s e w a t e r :
2
1. Press a glass against the water dispenser lever.
2. Remove the glass to stop dispensing. NOTE: Water may have an off-flavor if you do not use the
dispenser periodically. Dispense enough water every week to maintain a fresh supply.
Style 1
To turn off the dispenser, press the LOCK button until the indicator appears. The ice and water dispensers will not work. To unlock the dispenser, press the UNLOCK button until the indicator appears. Then continue to dispense ice or water as usual.
DISPENSER
The dispenser light
Style 1
The dispenser area has a light. It can be turned on manually by pressing the ON button (touch pad or rocker switch).
On some models: Whenever you use the dispenser the lever will automatically turn the light on.
LIGHT
OFF ON
NOTE: See the Changing the Light Bulbssection for information on changing the dispenser light bulb.
Style 2
When you use the dispenser, the lever will automatically turn the light on. If you want the light to be on continuously, you may chooseeitherONorNIGHTLIGHT.
ON: Press the LIGHT button to turn the dispenser light on. NIGHT LIGHT: Press the LIGHT button a second time to select
the Night Light mode. The dispenser light will automatically adjust to become brighter as the room brightens, dimmer as the room darkens.
OFF: Press the LIGHT button a third time to turn the dispenser light off.
The dispenser lights are LEDs which should not need to be changed. If it appears that your dispenser lights are not working, check to be sure that the light sensor is not blocked (in Night Light mode). See Troubleshootingfor more information.
LOCK
UNLOCK
Style 2
To turn off the dispenser, press and hold the LOCK OUT button until the indicator appears. The ice and water dispensers will not work. To unlock the dispenser, press the LOCK OUT button until the indicator disappears. Then continue to dispense ice or water as usual.
Water Filter Status Light
(on some models)
The water filter status light will help you know when to change your water filter cartridge. The light will change from green to yellow. This tells you that it is almost time to change the water filter cartridge (90% of the filter life has been used). It is recommended that you replace the base grille water filter cartridge when the water filter indicator light changes to red OR water flow to your water dispenser or ice maker decreases noticeably. (See Water Filtration System.”)
After changing the water filter cartridge, reset the water filter status light.
Style 1
Press the light switch 5 times within 10 seconds. The status light will change from red to green.
1
Style 2
Press and hold the water filter reset button until the status light turns green. Your reset button may be located on the water dispenser or on the control panel in the refrigerator compartment.
Dispenser Control Panel
The dispenser lock (on some models)
Your dispenser can be turned off for easy cleaning or to prevent accidental dispensing by small children and pets.
NOTE: The lock feature does not shut off power to the product, to the ice maker, or to the dispenser light. It simply deactivates the dispenser levers.
12
Non-indicator water filter (on some models)
If your refrigerator does not have the water filter status light, you should change the water filter cartridge every 6 to 9 months depending upon your usage. If the water flow to the water dispenser or ice maker decreases noticeably before 6 months have passed, replace the water filter cartridge more often.
Water Filtration System
(on somemodels)
NOTE: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.
Changing a base grille water filter cartridge
The base grille water filter is located below the freezer compartment door. Depending on your model, you may have a filter that is installed behind the base grille (Style 1) or a filter that is installed through the base grille (Style 2).
Style 1: Behind the base grille filter
1. Remove the base grille (see Door Removalsection). Rotate
the cartridge counterclockwise to a vertical position and pull the filter cartridge out.
NOTE: There will be water in the cartridge. Some spilling may occur.
3. Take the new cartridge out of its packaging and remove protective cover from o-rings.
4. Slide the cartridge cap onto the new cartridge. See illustration in Step 2.
5. With cartridge cap in the vertical position, push the new filter cartridge into the base grille until it stops. Rotate the cartridge cap clockwise to a horizontal position. Flush the water system (see Flushing the water system after replacing filter later in this section).
Flushing the water system after replacing filter
Use a sturdy container to depress the water dispenser bar until the water begins to flow. Flush the water system by dispensing and discarding 2 to 3 gal. (8 to 12 L) of water. Cleaning the system will take approximately 6 to 7 minutes and will help clear air from the line. Additional flushing may be required in some households.
NOTE: As air is cleared from the system, water may spurt out of the dispenser.
2. Take the new cartridge out of its packaging and remove
protectivecoverfromo-rings.
3. Push the new filter cartridge into the base until it stops.
Rotate the cartridge clockwise to a horizontal position. Flush the water system (see Flushing the water system after replacing filterlater in this section).
Style 2: Through the base grille filter
1. Locate the water filter cartridge cap in the front base grille.
Rotate the cap counterclockwise to a vertical position and pull the cap and filter cartridge out through the base grille.
NOTE: There will be water in the cartridge. Some spilling may occur.
2. Remove the cartridge cap by sliding it off the end of the old
cartridge. The cap will slide to the left or right. DO NOT DISCARD THE CAP.
Using the dispenser without the water filter
You can run the dispenser without a water filter cartridge. Your water will not be filtered.
1. Remove the base grille water filter cartridge. For Style 1, replacethebasegrilleafterremovingthefilter.
2. For Style 2, slide the cartridge cap off the end of the filter cartridge. DO NOT DISCARD THE CAP. With the cartridge cap in the vertical position, insert the cap into the base grille until it stops.
3. Rotate the cartridge cap to a horizontal position. The cartridge cap might not be even with the base grille.
Ice Maker and Storage Bin/Bucket
(on some models - Accessory)
Style 1
To turn the ice maker on/off
The on/off switch for the ice maker is a wire shutoff arm located onthesideoftheicemaker.
1. To turn the ice maker on, simply lower the wire shutoff arm. NOTE: Your ice maker has an automatic shutoff. As ice is
made,theicecubeswillfilltheicestoragebinandtheice cubes will raise the wire shutoff arm to the OFF (arm up) position.
13
2. To manually turn the ice maker off, lift the wire shutoff arm to
the OFF (arm up) position and listen for the click to make sure the ice maker will not continue to operate.
MAX
NORMAL
To increase ice production rate:
Normal Ice Production: In normal ice production mode, the ice maker should produce approximately 7 to 9 batches of ice in a 24-hour period. If ice is not being made fast enough, turn the Freezer Control toward a higher (colder) number in half number steps. (For example, if the control is at 3, move it to between 3 and 4.) Wait 24 hours between each increase.
Maximum Ice Production (on some models): In maximum ice production, the ice maker should produce approximately 10 to 14 batches of ice in a 24-hour period. If your refrigerator has the maximum ice production feature, push the switch to MAX.
To remove and replace ice storage bin:
1. Pull the covering panel out from the bottom and then slide it
back toward the rear.
2. Lift the wire shutoff arm so it clicks into the OFF (up) position.
Ice can still be dispensed, but no more can be made.
3. Lift up the front of the storage bin and pull it out.
To remove and replace the ice storage bucket:
1. Holdthebaseofthestoragebinwithbothhandsandpress
the release button to lift the storage bin up and out. NOTE: It is not necessary to turn the ice maker control to the
OFF (right) position when removing the storage bin. The sensor cover (flipper door) on the left wall of the freezer stops the ice maker from producing ice if the door is open or the storage bin is removed.
2. Replace the storage bin on the door and push down to make sure it is securely in place.
Clean the ice storage bin or bucket
1. Empty the ice container. Use warm water to melt the ice if
necessary. NOTE: Never use anything sharp to break up the ice in the
bin or bucket. This can cause damage to the ice container and the dispenser mechanism.
2. Wash ice bin or bucket with a mild detergent, rinse well and dry thoroughly. Do not use harsh or abrasive cleaners or solvents.
REMEMBER
4. Replace the bin by pushing it in all the way or the dispenser
will not work. Push the wire shutoff arm down to the ON position to restart ice production. Make sure the door is closed tightly.
Style 2
To turn the ice maker on/off:
The ON/OFF switch is located on the top right side of the freezer compartment.
1. To turn the ice maker on, slide the control to the ON (left)
position. NOTE: Your ice maker has an automatic shutoff. The ice
maker sensors will automatically stop ice production, but the control will remain in the ON (left) position.
2. To manually turn the ice maker off, slide the control to the
OFF (right) position.
Allow 24 hours to produce the first batch of ice.
Discard the first three batches of ice produced to avoid impurities that may be flushed out of the system.
The quality of your ice will be only as good as the quality of the water supplied to your ice maker.
Avoid connecting the ice maker to a softened water supply. Water softener chemicals (such as salt) can damage parts of the ice maker and lead to poor quality ice. If a softened water supply cannot be avoided, make sure the water softener is operating properly and is well maintained.
It is normal for the ice cubes to be attached at the corners. They will break apart easily.
For Style 1 ice maker, do not force the wire shutoff arm up or down.
Do not store anything on top of the ice maker or in the ice storage bin/bucket.
REFRIGERATOR
FEATURES
Your model may have some or all of these features. Features that can be purchased separately as product accessories are labeled with the word Accessory.Not all accessories will fit all models. If you are interested in purchasing one of the accessories, please call the toll-free number on the cover or in the “Accessories section.
14
Important information to know about glass shelves and covers:
Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. For your protection, tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use special care when re­moving them to avoid impact from dropping.
Refrigerator Shelves
Your model may have glass or wire shelves. Store similar foods together and adjust the shelves to fit different heights. This reduces the time the refrigerator door is open and saves energy.
Slide-out Shelves (on some models)
To remove and replace a shelf in a metal frame:
1. Pull the shelf forward to the stop. Tilt the front of the shelf up
and lift it slightly as you pull the shelf from the frame.
2. Replace the shelf by guiding it back into the slots on the
frame and pushing the shelf in past the stop.
Adjustable Flip-up Shelf
(on some models)
To raise or lower the shelf:
1. Raise the shelf by first sliding it back and down to make it
half-width. (You can use the shelf in this position to allow taller items to be stored on the shelf below.)
2. Lift the front of the shelf until it fits securely in place against the back wall. Lower the shelf securely back into position.
3. Pull the front of the shelf forward until it fits into place.
Drop-down shelf
(on some models)
To remove and replace the drop-down shelf:
1. Remove the drop-down shelf by sliding it up and back. Pull
forward slightly to release the rear pegs from the track as shown.
Shelves and Shelf Frames
To remove and replace a shelf/frame:
1. Remove the shelf/frame by tilting it up at the front and lifting it
outoftheshelfsupports.
2. Replace the shelf/frame by guiding the rear shelf hooks into
the shelf supports. Tilt the front of the shelf up until rear shelf hooks drop into the shelf supports. Check to make sure that the shelf is securely in position.
Flip-up Shelf
(on somemodels)
To raise or lower the shelf:
1. Raise the shelf by pulling forward on the lever located at the
bottom front of the shelf and lift until the shelf locks into the vertical position.
2. Lower the shelf until it is latched securely in place.
2. With the rear pegs released, pull the shelf down and forward.
3. Replace the shelf by sliding the front pegs into the track.
Push the shelf up and back until the rear pegs drop into the track. Pull down and forward to be sure the shelf is securely in place.
Deli Drawer
(on some models)
The deli drawer stores raisins, nuts, spreads, and other small items at normal refrigerator temperatures.
To remove and replace the deli drawer:
1. Remove the deli drawer by sliding it straight out to the stop.
Lift the front and slide the drawer out the rest of the way.
2. Replace the deli drawer by sliding it back past the stop.
15
Convertible Vegetable/Meat Drawer, Crisper
and Covers
(on somemodels)
Crisper and Convertible Vegetable Meat Drawers
To remove and replace drawers:
1. Slide crisper or meat drawer straight out to the stop. Lift the
front of drawer with one hand while supporting the bottom of drawer with other hand and slide the drawer out the rest of the way.
2. Replace the crisper or meat drawer by sliding it back in fully
past the drawer stop.
Crisper or Vegetable/Meat Drawer Covers
To remove and replace covers:
1. Remove the crisper and meat drawer. Press up in center of
crisper glass insert until it rises above the plastic frame. Holding the crisper glass firmly, carefully slide the glass insert forward to remove.
2. Lift crisper cover frame and remove. Repeat steps to remove
the meat drawer cover.
IMPORTANT: If food starts to freeze, move the control to the left (less cold). Remember to wait 24 hours between adjustments. Doing so gives the temperature of the food time to change.
Meat storage guide
Store most meat in original wrapping as long as it is airtight and moisture-proof. Rewrap if necessary. See the following chart for storage times. When storing meat longer than the times given, freeze the meat.
Fresh fish or shellfish.........................use same day as purchased
Chicken, ground beef, variety meat (liver, etc.) ................1-2 days
Cold cuts, steaks/roasts .................................................. 3-5 days
Cured meats...................................................................7-10 days
Leftovers - Cover leftovers with plastic wrap, aluminum foil, or plastic containers with tight lids.
Crisper Humidity Control
(on some models)
You can control the amount of humidity in the moisture-sealed crisper. Adjust the control to any setting between LOW and HIGH.
3. Replace back of meat drawer cover frame into supports or
slides on side walls of the refrigerator and lower or slide the front of the cover frame into place.
4. Slide rear of glass insert into cover frame and lower front into
place. Repeat steps to replace the crisper cover.
Convertible Vegetable/Meat Drawer
Temperature Control
(on somemodels)
The convertible vegetable/meat drawer can be adjusted to properly chill meats or vegetables. The air inside the pan is cooled to prevent spotfreezing and can be set to keep meats at the National Livestock and Meat Board recommended storage temperatures of 28°-32°F(-2°-0°C).
IMPORTANT: To extend freshness, wrap meats in airtight, moisture-proof materials before storing. Always store meat as recommended.
Adjusting the control
The convertible control comes preset at the lowest meat setting. To change a control setting: Move the control to the right
(colder) or to the left (less cold) as desired. To store vegetables: Set the control to VEG (all the way to the
left) to store vegetables at their optimal storage temperatures (which need to be warmer than those for meat).
LOW (open) lets moist air out of the crisper for best storage of fruits and vegetables with skins.
Fruit: Wash, let dry and store in refrigerator in plastic bag or crisper. Do not wash or hull berries until they are ready to use. Sort and keep berries in original container in crisper, or store in a loosely closed paper bag on a refrigerator shelf.
Vegetables with skins: Place in plastic bag or plastic container and store in crisper.
HIGH (closed) keeps moist air in the crisper for best storage of fresh, leafy vegetables.
Leafy vegetables: Wash in cold water, drain and trim or tear off bruised and discolored areas. Place in plastic bag or plastic container and store in crisper.
Wine or Can/Bottle Rack
(on some models - Accessory)
To remove and replace the wine rack (left) or can/bottle rack (right):
1. Remove the rack by pulling it straight out from the shelf.
2. Replace the rack by sliding it in between the shelf and the
wall of the refrigerator.
16
Utility Bin
(on some models - Accessory)
NOTE: For long-term storage, place eggs in a covered container or in their original carton on an interior shelf.
3. Replace the basket or bin by positioning it on the side wall guide rails. Lift the basket or bin front slightly while pushing it past the guide rail stops and slide basket or bin in the rest of the way.
DOOR FEATURES
FREEZER FEATURES
Your model may have some or all of these features. Features that can be purchased separately as product accessories are labeled with the word Accessory.Not all accessories will fit all models. If you are interested in purchasing one of the accessories, please call the toll-free number on the cover or in the Accessories section.
Freezer Shelf
(number of shelves varies with model)
To remove and replace the shelf:
1. Lifttheshelfoffofthesupports.
2. Slide it out of the shelf support holes.
3. Replaceshelfinthereverseorder.
Frozen food storage guide
Storage times will vary according to the quality and type of food, the type of packaging or wrap used (should be airtight and moisture-proof), and the storage temperature. Ice crystals inside a sealed package are normal. This simply means that moisture in the food and air inside the package have condensed, creating ice crystals.
Put no more unfrozen food into the freezer than will freeze within 24 hours (no more than 2 to 3 lbs. of food per cubic foot [907-1,350 g per L] of freezer space). Leave enough space in the freezer for air to circulate around packages. Be careful to leave enough room for the door to close tightly.
For more information on preparing food for freezing, check a freezer guide or reliable cookbook.
Your model may have some or all of these features. Features that can be purchased separately as product accessories are labeled with the word Accessory.Not all accessories will fit all models. If you are interested in purchasing one of the accessories, please call the toll-free number on the cover or in the “Accessories section.
Tilt-out Freezer Door Bin
(on some models)
Remove and replace the bin:
1. Remove the bin by pulling out on the tabs behind the basket
to release it from the door liner.
2. Replace the bin by aligning the tabs with the buttons on the sides of the door liner. Firmly snap the tabs onto the buttons as shown.
Chilled Door Bin
(on some models)
Cool air from the freezer is directed to the refrigerator door bin directly beneath the vents.
NOTE: The dairy compartment and can rack are not chilled.
FreezerBasketorBin
(plasticbinonsomemodels)
The freezer basket or bin can be used to store bags of frozen fruits and vegetables that may slide off freezer shelves.
To remove and replace the freezer basket or bin:
1. Remove basket or bin by sliding it out to the stop.
2. Liftthefrontofthebasketorbinandslideitouttherestofthe
way.
17
Loading...
+ 39 hidden pages