Whirlpool GU180ESJQ, GU180ESJS, GU180ESJB INSTRUCTION FOR USE

GB GU 180 ES

WASH CYCLE CHART

Further indications are given in the pages to follow and in the user instructions.

				Rinse aid level indicator						Options														Start button
										Half load / Multizone button
				Add rinse aid.																				Indicator lamp lit while the
										Load the lower rack only. This function can be used with any wash cycle.
																								dishwasher is operating.
				Cycle status indicator
				Rinse / Pre-wash						Delay start button														Flashes when a fault occurs.
																								Switches off at the end of the cycle.
				Washing						The wash cycle can be programmed to start after 3-6-9 hours.
										Select the desired delay time then press the Start button. The dishwasher will														Cycle selector
				Drying						start at the set time.
				End of cycle
											Place the detergent in the:														Consumption		1)
											small					large									Normal load /
			Cycle description				Recommended load				compartment				compartment									(Half load / Multizone)
																					Water				Energy		Time
																					(Litres)				(kWh)		(Min.)
				Rince / Pre-wash		Dishes to be washed later.					-				-				5.0			(4.0)			0.02	(0.02)	10	(10)
				Rapid 40° C		Rapid short wash for lightly soiled dishes.					-					X			13.5			(10.5)			0.05	(0.03)	21	(20)
				Crystal / China 40° C		Crystal, fine china and other lightly soiled delicate items.					-					X			13.5			(10.5)			0.45	(0.40)	56	(54)
				Bio Eco 50° C	2)	Normally soiled dishes.					-					X			13.5			(10.5)			1.07	(0.83)	93	(81)
				Normal 50° C	3)	Normally soiled dishes.						X				X			18.5			(14.5)			0.96	(0.80)	96	(91)
				Heavy 65° C		Normally or heavily soiled dishes.						X				X			18.5			(14.5)			1.11	(0.92)	102	(90)
				Intensive 70° C		Heavily soiled pots and pans.						X				X			22.5			(18.0)			1.28	(1.11)	106	(98)
	1) Your values may vary due to load composition, water inlet temperature, water hardness and power supply voltage.																								5019 100 91300
	2) Cycle recommended for use with the new generation “enzyme” based detergents.

3) Cycle recommended for use with traditional non-enzyme based detergents.	(We reserve the right to make technical modifications)

How to use the dishwasher

Upper and lower rack

1.After loading the dishwasher, close the door properly. Ensure that the water supply is turned on.

2.The dishwasher switches on automatically as soon as the cycle selector knob is turned. One of the cycle indicator lamps will switch on.

3.Turn the selector knob to select the desired cycle. The corresponding indicator lamp lights up. If required, select options (if supplied).

4.Press the Start button to start the selected cycle. The Start indicator lamp will light up. Once set, the programmed data cannot be altered by turning the cycle selector knob.

Note: once the Start button has been pressed, the dishwasher memorises the last cycle selected. This information

remains in the memory even during interruption of the power supply.

To change the selected cycle, press the Start button and hold it

depressed for about 5 seconds, until the Start indicator lamp switches off. Select a new cycle and press the Start button.

Note: if the dishwasher is switched off during a wash cycle, when switched on again it will resume the wash cycle from where it was interrupted.

Only open the dishwasher door if strictly necessary during a wash cycle and exercise maximum caution. Escaping steam may be extremely hot.

5.To indicate the end of the cycle, the Start indicator lamp switches off and the End indicator lamp (if fitted) lights up (for about 30 min.).

6.Once the start indicator lamp has switched off, turn the cycle selector knob to the zero position to switch off the dishwasher. At this time, all the indicator lights will switch off.

7.Open the door slowly (beware of hot steam). Unload the lower rack before the upper one.

Upper rack

Rack height adjustment:

(The dishwasher is delivered with the upper rack in the top position).

The rack height can also be changed when loaded.

•To lower: pull out the two side handles and gently lower the rack.

•To raise: pull up the two side handles until the rack clicks into place.

• The rack must be level on both sides.

Lower rack

Cup holders:

•	Down: cups and long-stemmed glasses.	A
•	Up: plates.	A

C

“Flex 3”: multi-purpose support

•To be used, for example, for longhandled utensils (arrange knives with the blade facing downwards), cups and glasses.

•May be used in three different positions (see also “Dishwasher loading instructions” on Page 4).

1.Upon the left-hand side of the rack.

2.Upside-down, towards the centre of the rack.

3.Upside-down, towards the left side.

Glass holder:

Half load / Multizone:

Loading the lower rack only gives greater washing power, especially for plates and pots.

Plate holder tines:

•(A) may be lowered to increase available space.

Cutlery basket:

•The cutlery basket (C) can be removed to increase available space when necessary.

C

Please read the user instructions carefully.