Whirlpool KTRC22ELSS02, ET9FTTXLT12, ET1FTTXKB02, GT1SHTXLQ01, KTRC22ELWH00 User Manual

...
®
SIDE BY SIDE
REFRIGERATOR
Use & Care Guide
For questions about features, operation/performance
parts, accessories or service, call:
In Canada, call for assistance
www.whirlpool.com
and service, call:
or visit our website at...
or
1-800-253-1301
1-800-461-5681
1-800-807-6777
www.whirlpool.com/canada
.
RÉFRIGÉRATEUR
CÔTEÀCÔTE
Guide d’utilisation
et d’entretien
Au Canada, pour assistance, composez le
installation ou le service
ou visitez notre site web à
www.whirlpool.com/canada
1-800-807-6777
1-800-461-5681
, pour
2220697
Table of Contents/Table des matières .............2

TABLE OF CONTENTS

TABLE DES MATIÈRES
REFRIGERATOR SAFETY .............................................................3
Proper Disposal of Your Old Refrigerator....................................3
REFRIGERATOR INSTALLATION.................................................4
Unpacking ....................................................................................4
Location Requirements................................................................4
Electrical Requirements ...............................................................5
Base Grille ....................................................................................5
Door Removal...............................................................................6
Door Closing.................................................................................8
Water Supply Connection............................................................8
Water System Preparation...........................................................9
Normal Sounds ............................................................................9
REFRIGERATOR USE..................................................................10
Ensuring Proper Air Circulation..................................................10
Using the Controls .....................................................................10
Water and Ice Dispensers..........................................................10
Interior Water Filtration System .................................................11
Ice Maker and Storage Bin/Bucket............................................12
REFRIGERATOR FEATURES ......................................................13
Refrigerator Shelves...................................................................13
Flip-up Shelf ...............................................................................13
Adjustable Flip-up Shelf.............................................................13
Deli Drawer.................................................................................13
Convertible Vegetable/Meat Drawer, Crisper and Covers ........14
Convertible Vegetable/Meat Drawer Temperature Control.......14
Crisper Humidity Control ...........................................................14
Wine or Can/Bottle Rack ...........................................................14
Utility Bin ....................................................................................14
FREEZER FEATURES..................................................................15
Freezer Shelf ..............................................................................15
Freezer Basket or Bin.................................................................15
DOOR FEATURES........................................................................15
Door Rails...................................................................................15
Can Racks and Door Bins..........................................................15
REFRIGERATOR CARE ...............................................................16
Cleaning......................................................................................16
Changing the Light Bulbs...........................................................16
Power Interruptions....................................................................17
Vacation and Moving Care.........................................................17
TROUBLESHOOTING ..................................................................17
ASSISTANCE OR SERVICE.........................................................20
In the U.S.A. ...............................................................................20
In Canada ...................................................................................21
Accessories................................................................................21
WATER FILTER CERTIFICATIONS.............................................21
PRODUCT DATA SHEETS...........................................................22
WARRANTY ..................................................................................23
SÉCURITÉ DU RÉFRIGÉRATEUR ..............................................25
Mise au rebut de votre vieux réfrigérateur.................................25
INSTALLATION DU RÉFRIGÉRATEUR ......................................26
Déballage....................................................................................26
Emplacement d’installation........................................................26
Spécifications électriques ..........................................................27
Grille de la base..........................................................................27
Enlèvement des portes...............................................................28
Fermeture des portes.................................................................30
Raccordement de la canalisation d'eau ....................................30
Préparation du système d’eau...................................................31
Sons normaux ............................................................................31
UTILISATION DU RÉFRIGÉRATEUR..........................................32
Pour s’assurer d’une circulation d’air appropriée......................32
Utilisation des commandes........................................................32
Distributeurs d’eau et de glaçons..............................................33
Système de filtration d’eau intérieur ..........................................34
Machine à glaçons et bac/seau d’entreposage ........................35
CARACTÉRISTIQUES DU RÉFRIGÉRATEUR ...........................36
Tablettes du réfrigérateur...........................................................36
Tablette relevable .......................................................................36
Tablette relevable ajustable .......................................................36
Tiroir pour spécialités alimentaires ............................................37
Tiroir à légumes/viande convertible,
bac à légumes et couvercles .....................................................37
Réglage de la température du tiroir à
légumes/viande convertible .......................................................37
Réglage de l’humidité dans le bac à légumes...........................37
Casier à vin ou porte-cannettes/bouteilles................................38
Casier utilitaire............................................................................38
CARACTÉRISTIQUES DU CONGÉLATEUR...............................38
Tablette de congélateur .............................................................38
Panier ou bac de congélateur....................................................38
CARACTÉRISTIQUES DE LA PORTE.........................................39
Tringles dans la porte.................................................................39
Porte-cannettes et balconnets...................................................39
ENTRETIEN DU RÉFRIGÉRATEUR ............................................39
Nettoyage ...................................................................................39
Remplacement des ampoules d’éclairage ................................40
Pannes de courant .....................................................................40
Entretien avant les vacances ou lors d’un déménagement.......41
DÉPANNAGE.................................................................................41
ASSISTANCE OU SERVICE.........................................................45
Aux États-Unis............................................................................45
Au Canada..................................................................................45
Accessoires ................................................................................45
FEUILLES DE DONNÉES SUR LE PRODUIT.............................46
GARANTIE.....................................................................................47
2

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.
This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word DANGER or
WARNING. These words mean:
You can be killed or seriously injured if you don't immediately follow instructions.
can be killed or seriously injured if you don't
You follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
WARNING:
precautions:
happen if the instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic
Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.
Do not use an extension cord. Disconnect power before servicing.
Replace all panels before operating. Remove doors from your old refrigerator.
Use nonflammable cleaner.
Keep flammable materials and vapors, such as gasoline, away from refrigerator.
Use two or more people to move and install refrigerator.
Disconnect power before installing ice maker (on ice maker kit ready models only).
Use a sturdy glass when dispensing ice or water (on some models).
SAVE THESE INSTRUCTIONS
Proper Disposal of Your Old Refrigerator
WARNING
Suffocation Hazard Remove doors from your old refrigerator. Failure to do so can result in death or
brain damage.
IMPORTANT
of the past. Junked or abandoned refrigerators are still dangerous – even if they will sit for “just a few days.” If you are getting rid of your old refrigerator, please follow these instructions to help prevent accidents.
: Child entrapment and suffocation are not problems
Before you throw away your old refrigerator or freezer:
Take off the doors.
Leave the shelves in place so that children may not easily climb inside.
3
REFRIGERATOR

Location Requirements

INSTALLATION

Unpacking

WARNING
Excessive Weight Hazard
Use two or more people to move and install refrigerator.
Failure to do so can result in back or other injury.
Removing packaging materials
Remove tape and glue residue from surfaces before turning on the refrigerator. Rub a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry.
Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your refrigerator. For more information, see the Refrigerator Safety section.
When Moving Your Refrigerator:
Your refrigerator is heavy. When moving the refrigerator for cleaning or service, be sure to protect the floor. Always pull the refrigerator straight out when moving it. Do not wiggle or walk the refrigerator when trying to move it, as floor damage could occur.
Cleaning before use
After you remove all of the packaging materials, clean the inside of your refrigerator before using it. See the cleaning instructions in the Refrigerator Care section.
WARNING
Explosion Hazard
Keep flammable materials and vapors, such as gasoline, away from refrigerator.
Failure to do so can result in death, explosion, or fire.
To ensure proper ventilation for your refrigerator, allow for (1.25 cm) space on each side and at the top. When installing your refrigerator next to a fixed wall, leave 2 in. (5.08 cm) minimum on each side (depending on your model) to allow for the door to swing open. If your refrigerator has an ice maker, allow extra space at the back for the water line connections.
Do not install the refrigerator near an oven, radiator, or
NOTE:
other heat source, nor in a location where the temperature will fall below 55°F (13°C).
1
/
2
" (1.25 cm)
¹⁄₂
in.
Important information to know about glass shelves and covers:
Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. For your protection, tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use special care when re­moving them to avoid impact from dropping.
4
2" (5.08 cm)

Electrical Requirements

WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in
death, fire, or electrical shock.
Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical connection:

Base Grille

To remove the base grille:
Open both refrigerator doors.
1.
Place hands along the ends of the grille, with your thumbs
2.
along the top. Push in with your thumbs and pull up on the bottom.
Be sure to refasten the Tech Sheet behind the base grille
NOTE:
after cleaning.
To replace the base grille:
Open the doors.
1.
Line up the grille support tabs with the metal clips.
2.
Push the grille firmly to snap it into place.
3.
Recommended grounding method
A 115 Volt, 60 Hz., AC only 15 or 20 ampere fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an extension cord.
Before performing any type of installation, cleaning, or
NOTE:
removing a light bulb, turn the control (Thermostat, Refrigerator or Freezer Control depending on the model) to OFF and then disconnect the refrigerator from the electrical source. When you are finished, reconnect the refrigerator to the electrical source and reset the control (Thermostat, Refrigerator or Freezer Control depending on the model) to the desired setting.
5
¹⁄₄
¹⁄₂
in.,
TOOLS NEEDED: IMPORTANT:
adjustable door or utility bins from doors.
Before you begin, turn the refrigerator control OFF, unplug refrigerator or disconnect power. Remove food and any
in., and
⁵⁄₁₆
in. hex-head socket wrenches, a flat-head screwdriver and a Phillips screwdriver.
Disconnect power before removing doors. Reconnect both ground wires before operating. Failure to do so can result in death or electrical shock.
4
Top Left Hinge

Door Removal

Electrical Shock Hazard
5
Door Removal
6
Top Right Hinge
1
1. Do Not Remove Screw
3
Water Dispenser Tubing Connection
1
1. Red Outer Ring
2
Base Grille
1
Handle Removal (Optional)
1
1. Do Not Remove Screw
7
Bottom Hinge
1
1. Do Not Remove Screw
8
Door Alignment
1
1. Leveling Screw
It may only be necessary to remove either the door handle or the doors to get your product through the doorway of your
NOTE:
residence. Measure the door opening to determine whether to remove the refrigerator handles or the doors.
6
Handle Removal (optional)
Door and Hinge Replacement
Apply firm pressure with your hand on the face of trim. Slide
1.
top trim up and bottom trim down away from handle. Lift trim pieces off shoulder screws (see Graphic 1).
Some models include accent pieces between the handle
NOTE:
and the handle trim. If your model includes the accents, you will need to carefully remove them with a flat-head screwdriver before removing the handle screws. The accent pieces are optional and can be reinstalled or left off of the handle assembly.
Remove handle screws and handles.
2.
Move refrigerator into place. Replace handles as shown (see
3.
Graphic 1).
Door Removal
WARNING
Electrical Shock Hazard
Disconnect power before removing doors. Failure to do so can result in death or
electrical shock.
Replace both bottom hinges, if removed. Tighten screws.
1.
Assistance may be needed to feed the water dispenser
2.
tubing through the bottom hinge while reinstalling the freezer door. Carefully feed the dispenser tubing through the bottom left hinge before replacing the door on the hinge.
Provide additional support for the doors while the top
NOTE:
hinges are being replaced. Do not depend on the door magnets to hold the doors in place while you are working.
Reconnect water dispenser tubing by pushing tubing into
3.
fitting until it stops and black mark touches face of fitting (see Graphic 3). On some models, replace tubing in hose clip.
Align and replace the top left hinge as shown (see Graphic 4).
4.
Tighten screws.
WARNING
Electrical Shock Hazard
Reconnect both ground wires. Failure to do so can result in death or
electrical shock.
Unplug refrigerator or disconnect power.
1.
Open both refrigerator doors. Remove the base grille by
2.
pulling up on the bottom outside corners (see Graphic 2). Close both doors and keep them closed until you are ready to
3.
lift them free from the cabinet. If you have a dispenser (ice or water), disconnect the water
4.
dispenser tubing located behind the base grille on the freezer door side (see Graphic 3).
Press the red outer ring against the face of fitting and pull the dispenser tubing free.
On some models, remove tubing from hose clip.
Remove top left hinge screw and cover as shown (see
5.
Graphic 4). Disconnect wiring plug and both ground wires from ground
6.
wire screw (on some models) as shown (see Graphic 4). Remove remaining left hinge screws and hinge as shown (see
7.
Graphic 4). DO NOT REMOVE SCREW 1. Carefully lift freezer door straight up off bottom hinge (see
8.
Graphic 5). The water dispenser tubing remains attached to the freezer door and pulls through the bottom left hinge. Make sure you protect the dispenser tubing from damage.
Remove top right hinge cover and screws as shown (see
9.
Graphic 6). DO NOT REMOVE SCREW 1. Lift the refrigerator door straight up off bottom hinge.
10.
It may not be necessary to remove the bottom hinge to move
11.
the refrigerator through a doorway. Both bottom hinges have similar construction.
Disassemble the hinges as shown (see Graphic 7). DO NOT REMOVE SCREW 1.
Style 1
Reconnect both ground wires.
Reconnect wiring plug.
Style 1
Style 2
Reconnect wiring plug.
Replace left hinge cover and screws.
5.
Replace the refrigerator door by carefully lifting the door onto
6.
the bottom right hinge. Align and replace the top right hinge as shown (see Graphic
7.
6). Tighten screws. Replace hinge cover and screws. Tighten screws.
8.
Plug into a grounded 3 prong outlet.
9.
7

Door Closing

Your refrigerator has two front adjustable rollers one on the right and one on the left. If your refrigerator seems unsteady or if you want the doors to close more easily, adjust the refrigerator's tilt using the instructions below:
Move the refrigerator into its final position.
1.
The two leveling screws are part of the front roller assemblies
2.
which are at the base of the refrigerator on either side (see Graphic 8).
Use a hex-head socket wrench to adjust the leveling screws.
3.
Turn the leveling screw to the right to raise that side of the refrigerator or turn the leveling screw to the left to lower that side. It may take several turns of the leveling screws to adjust the tilt of the refrigerator (see Graphic 8).
Having someone push against the top of the
NOTE:
refrigerator takes some weight off the leveling screws and rollers. This makes it easier to adjust the screws.
Open both doors again and check to make sure that they
4.
close as easily as you like. If not, tilt the refrigerator slightly more to the rear by turning both leveling screws to the right. It may take several more turns, and you should turn both leveling screws the same amount.
Replace the base grille.
5.
Be sure to refasten the Tech Sheet behind the base grille.
NOTE:
Using a grounded drill, drill a
5.
you have selected.
1. Cold Water Pipe
2. Pipe Clamp
3. Copper Tubing
4. Compression Nut
Fasten the shutoff valve to the cold water pipe with the pipe
6.
clamp. Be sure the outlet end is solidly in the in the water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp screws carefully and evenly so washer makes a watertight seal. Do not overtighten or you may crush the copper tubing.
Slip the compression sleeve and compression nut on the
7.
copper tubing as shown. Insert the end of the tubing into the outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten.
Place the free end of the tubing in a container or sink, and
8.
turn ON the main water supply. Flush the tubing until water is clear. Turn OFF the shutoff valve on the water pipe. Coil the copper tubing.
¹⁄₄
in. hole in the cold water pipe
5. Compression Sleeve
6. Shutoff Valve
7. Packing Nut
¹⁄₄
in. drilled hole

Water Supply Connection

Read all directions carefully before you begin.
IMPORTANT:
If you turn the refrigerator on before the water line is connected, turn the ice maker OFF.
All installations must meet local plumbing code requirements.
Use copper tubing and check for leaks. Install copper tubing only in areas where temperatures will remain above freezing.
Tools required:
wrenches or two adjustable wrenches, bit, hand drill or electric drill (properly grounded).
Your refrigerator dealer has a kit available with a
NOTE:
(6.35 mm) saddle-type shutoff valve, a union, and copper tubing. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes. Do not use a piercing-type or (4.76 mm) saddle valve which reduces water flow and clogs more easily.
Standard screwdriver,
⁷⁄₁₆
in. and
¹⁄₄
in. nut driver and drill
Cold water supply
Connect the ice maker to a cold water line with water pressure between 30 and 120 psi. If you have questions about your water pressure, call your utility company.
Connecting to Water Line
Unplug refrigerator or disconnect power.
1.
Turn OFF main water supply. Turn ON nearest faucet long
2.
enough to clear line of water. Locate a ½ in. to 1
3.
water pipe near the refrigerator.
Horizontal pipe will work, but drill on the top side of
NOTE:
the pipe, not the bottom. This will help keep water away from the drill and normal sediment from collecting in the valve.
Determine the length of copper tubing you need. Measure
4.
from the connection on the lower left rear of refrigerator to the water pipe. Add 7 ft. (2.1 m) to allow for cleaning. Use (6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.
¹⁄₄
in. (1.25 cm to 3.18 cm) vertical COLD
¹⁄₂
in. open-end
¹⁄₄
in.
³⁄₁₆
¹⁄₄
in.
in.
Connecting to Refrigerator
Attach the copper tube to the valve inlet using a compression
1.
nut and sleeve as shown. Tighten the compression nut. Do not overtighten. Use the tube clamp on the back of the refrigerator to secure the tubing to the refrigerator as shown. This will help prevent damage to the tubing when the refrigerator is pushed back against the wall.
Turn shutoff valve ON.
2.
Check for leaks. Tighten any connections (including
3.
connections at the valve) or nuts that leak.
1. Tube Clamp
2. Copper Tubing
The ice maker is equipped with a built-in water strainer. If
4.
your water conditions require a second water strainer, install it in the Obtain a water strainer from your nearest appliance dealer.
Plug in refrigerator or reconnect power.
5.
¹⁄₄
in. (6.35 mm) water line at either tube connection.
3. Compression Nut
4. Valve Inlet
8

Water System Preparation

(on some models)
Please read before using the water system. Immediately after installation, follow the steps below to make
sure that the water system is properly cleaned.
Turn off the ice maker by opening the freezer door and lifting
1.
up the wire shutoff arm as shown.
Install the interior water filter cartridge (on some models). The
2.
interior water filter mounting bracket is located in the upper corner of the fresh food compartment of the refrigerator.
NOTE: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.
Carefully remove the interior water filter cartridge from its packaging. Remove the red cap from the cartridge.
Apply the appropriate month sticker to the cartridge as a reminder to replace the cartridge within six months. Then apply the Water Filter Replacement Reminder sticker to your calendar.
Line up the INSTALL mark on the water filter label with the indicator line that is molded into the filter mounting bracket cover. Push the cartridge into the filter mounting bracket. Twist the cartridge into place. The REMOVE mark should be lined up with the indicator line located on the front cover.
¹⁄₄
turn to the right to lock it

Normal Sounds

Your new refrigerator may make sounds that your old one didn’t make. Because the sounds are new to you, you might be concerned about them. Most of the new sounds are normal. Hard surfaces, such as the floor, walls, and cabinets, can make the sounds seem louder. The following describes the kinds of sounds and what may be making them.
If your product is equipped with an ice maker, you will hear a buzzing sound when the water valve opens to fill the ice maker for each cycle.
Your refrigerator is designed to run more efficiently to keep your food items at the desired temperatures and to minimize energy usage. The high efficiency compressor and fans may cause your refrigerator to run longer than your old one. You may also hear a pulsating or high-pitched sound from the compressor or fans adjusting to optimize performance.
You may hear the evaporator fan motor circulating air through the refrigerator and freezer compartments. The fan speed may increase as you open the doors or add warm food.
Rattling noises may come from the flow of refrigerant, the water line, or items stored on top of the refrigerator.
Water dripping on the defrost heater during a defrost cycle may cause a sizzling sound.
As each cycle ends, you may hear a gurgling sound due to the refrigerant flowing in your refrigerator.
Contraction and expansion of the inside walls may cause a popping noise.
You may hear air being forced over the condenser by the condenser fan.
You may hear water running into the drain pan during the defrost cycle.
Use a sturdy container to depress the water dispenser bar
3.
until the water begins to flow. Flush the water system by dispensing and discarding 2 to 3 gal. (8 to 12 L) of water. Cleaning the system will take approximately 6 to 7 minutes and will help clear air from the line. Additional flushing may be required in some households.
As air is cleared from the system, water may spurt out
NOTE:
of the dispenser. Inspect the filter system for water leaks. If you see water
4.
leaks, see the “Troubleshooting” section. Turn on the ice maker by opening the freezer door and
5.
lowering the wire shutoff arm as shown.
Please refer to the Ice Maker section for further instructions on the operation of your ice maker.
Allow 24 hours to produce the first batch of ice.
Discard the first three batches of ice produced.
9

REFRIGERATOR USE

Ensuring Proper Air Circulation

In order to ensure proper temperatures, you need to permit air to flow between the two sections. Cold air enters the bottom of the freezer section and moves up. It then enters the refrigerator section through the top vent. Air then returns to the freezer as shown.
The preset settings should be correct for normal household usage. The controls are set correctly when milk or juice is as cold as you like and when ice cream is firm.
If the temperature is too warm or too cold in the refrigerator or freezer, first check the air vents to be sure they are not blocked before adjusting the controls.
Adjusting Rotary Controls
If you need to adjust temperatures, adjust the refrigerator temperature first.
Wait at least 24 hours between adjustments and then
NOTE:
recheck the temperatures.
CONDITION/REASON: SETTING
REFRIGERATOR too cold
Not set correctly for your conditions
REFRIGERATOR too warm
Door opened often, large amount of food added or room temperature very warm
ADJUSTMENT:
REFRIGERATOR Control one setting lower
REFRIGERATOR Control one setting higher
Do not block any of these vents with food such as soda, cereal, bread, etc. If the vents are blocked, airflow will be prevented and the temperature controls will not function properly.
IMPORTANT:
odors formed in one section will transfer to the other. You must thoroughly clean both sections to eliminate odors. To prevent odor transfer from food, wrap or cover foods tightly.
Because air circulates between both sections, any

Using the Controls

Rotary Controls (on some models)
For your convenience, your refrigerator controls are preset at the factory. When installing your refrigerator, make sure that the controls are still preset to the “mid-settings” as shown.
IMPORTANT:
Your product will not cool when the REFRIGERATOR Control is set to OFF.
The Refrigerator Control adjusts the refrigerator compartment temperature. The Freezer Control adjusts the freezer compartment temperature. Settings to the left of the mid­setting make the temperature less cold. Settings to the right of the mid-setting make the temperature colder.
Wait 24 hours before you put food into the refrigerator. If you add food before the refrigerator has cooled completely, your food may spoil.
Adjusting the Refrigerator and Freezer Controls to a
NOTE:
higher (colder) setting will not cool the compartments any faster.
FREEZER too cold
Not set correctly for your conditions
FREEZER too warm/too little ice
Door opened often, or large amount of food added or very cold room temperature (cant cycle often enough) or heavy ice usage
FREEZER Control one setting lower
FREEZER Control one setting higher

Water and Ice Dispensers

(on some models)
WARNING
Cut Hazard Use a sturdy glass when dispensing ice or water. Failure to do so can result in cuts.
Depending on your model, you may have one or more of the following options: the ability to select either crushed or cubed ice, a special light that turns on when you use the dispenser, or a lock option to avoid accidental dispensing.
The ice dispenser
Ice dispenses from the ice maker storage bin in the freezer. When the dispenser lever is pressed:
A trap door opens in a chute between the dispenser and the ice bin. Ice moves from the bin and falls through the chute.
When you release the dispenser lever, the trap door closes and the ice dispensing stops. The dispensing system will not operate when the freezer door is open.
10
Some models dispense both cubed and crushed ice. Before dispensing ice, select which type of ice you prefer. The button controls are designed for easy use and cleaning.
For cubed ice, press the CUBE button until the red indicator appears in the window above the CUBE button.
ICE
CRUSH CUBE
For crushed ice, press the CRUSH button until the red indicator appears in the window above the CRUSH button.
For crushed ice, cubes are crushed before being dispensed. This may cause a slight delay when dispensing crushed ice. Noise from the ice crusher is normal, and pieces of ice may vary in size. When changing from CRUSH to CUBE, a few ounces of crushed ice will be dispensed along with the first cubes.
To dispense ice:
Press button for the desired type of ice.
1.
Press a sturdy glass against the ice dispenser lever. Hold the
2.
glass close to the dispenser opening so ice does not fall outside of the glass.
IMPORTANT:
the lever in order to activate the ice dispenser. Pressing hard will not make the ice dispense faster or in greater quantities.
Remove the glass to stop dispensing.
3. NOTE:
from new plumbing and parts. Throw the ice away. Also, take large amounts of ice from the ice bin, not through the dispenser.
You do not need to apply a lot of pressure to
The first few batches of ice may have an off-flavor
The water dispenser
If you did not flush the water system when the refrigerator was first installed, press the water dispenser bar with a glass or jar until you draw and discard 2 to 3 gal. (8 to 12 L) or approximately 6 to 7 minutes of water after water begins dispensing. It will take 3 to 4 minutes for the water to begin dispensing. The water you draw and discard cleans the system and helps clear air from the lines. Allow several hours for the refrigerator to cool down and chill water.
IMPORTANT:
tray at the bottom of the dispenser is designed to catch small spills and allow for easy cleaning. There is no drain in the tray. The tray can be removed from the dispenser and carried to the sink to be emptied or cleaned.
Depending on your model, the small removable
To d ispen se wa ter:
Press a glass against the water dispenser lever.
1.
Remove the glass to stop dispensing.
2.
Dispense enough water every week to maintain a fresh
NOTE:
supply.
The dispenser light
The dispenser area has a light. It can be turned on manually by pressing the ON button at the right-hand side of the control panel. The red indicator above the ON button will appear.
On some models: Whenever you use the dispenser the lever will automatically turn the light on.
LIGHT
OFF ON
See the Changing the Light Bulbs section for
NOTE:
information on changing the dispenser light bulb. On models without crushed ice, the light switch is a rocker-style
type. Push the switch to turn the light on, and push again to turn the light off.
The dispenser lock (on some models)
Your dispenser can be turned off for easy cleaning or to prevent accidental dispensing by small children and pets. To turn off the dispenser, press the LOCK button. The indicator will appear above the LOCK button and the ice and water dispensers will not work. To unlock the dispenser, press the UNLOCK button until the indicator appears. Then continue to dispense ice or water as usual.
DISPENSER
LOCK
UNLOCK
The lock feature does not shut off power to the product,
NOTE:
to the ice maker, or to the dispenser light. It simply deactivates the dispenser levers.

Interior Water Filtration System

(on some models)
The interior water filter cartridge is located in the upper corner of the fresh food compartment of the refrigerator. The interior water filter cartridge should be replaced every six months or earlier if the flow of water to your water dispenser or ice maker decreases noticeably.
Replacing the interior water filter cartridge
Twist the interior water filter cartridge
1.
INSTALL mark will be lined up with the indicator line located on the filter mounting bracket cover.
Gently pull down on the cartridge to remove it from the filter
2.
mounting bracket assembly. To prevent water from spilling inside the refrigerator, DO NOT TIP the cartridge. Dispose of the cartridge.
Install the new interior water filter cartridge. You can run the
3.
dispenser without a water filter cartridge, but your water will not be filtered.
NOTE: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.
Carefully remove the interior water filter cartridge from its packaging. Remove the red cap from the cartridge.
¹⁄₄
turn to the left. The
11
Apply the appropriate month sticker to the cartridge as a reminder to replace the cartridge within six months. Then apply the Water Filter Replacement Reminder sticker to your calendar as a reminder to replace the cartridge in six months.
Line up the INSTALL mark on the water filter label with the
4.
indicator line that is molded into the filter mounting bracket cover. Push the cartridge into the filter mounting bracket. Twist the cartridge
¹⁄₄
turn to the right to lock it into place. The REMOVE mark should be lined up with the indicator line located on the front cover.
Use a sturdy container to depress the water dispenser bar
5.
until the water begins to flow. Flush the water system by dispensing and discarding 2 to 3 gal. (8 to 12 L) of water. Cleaning the system will take approximately 6 to 7 minutes and will help clear air from the line. Additional flushing may be required in some households.
As air is cleared from the system, water may spurt out
NOTE:
of the dispenser. Inspect the filter system for water leaks. If you see water
6.
leaks, see the “Troubleshooting” section.

Ice Maker and Storage Bin/Bucket

(on some models - Accessory)
To turn the ice maker on/off:
The on/off switch for the ice maker is a wire shutoff arm located on the side of the ice maker.
To turn the ice maker on, simply lower the wire shutoff arm.
1.
Your ice maker has an automatic shutoff. As ice is
NOTE:
made, the ice cubes will fill the ice storage bin and the ice cubes will raise the wire shutoff arm to the OFF (arm up) position.
To manually turn the ice maker off, lift the wire shutoff arm to
2.
the OFF (arm up) position and listen for the click to make sure the ice maker will not continue to operate.
MAX
NORMAL
To increase ice production rate:
Normal Ice Production:
In normal ice production mode, the ice maker should produce approximately 7 to 9 batches of ice in a 24-hour period. If ice is not being made fast enough, turn the Freezer Control toward a higher (colder) number in half number steps. (For example, if the control is at 3, move it to between 3 and 4.) Wait 24 hours between each increase.
Maximum Ice Production (on some models):
In maximum ice production, the ice maker should produce approximately 10 to 14 batches of ice in a 24-hour period. If your refrigerator has the maximum ice production feature, push the switch to MAX.
To remove and replace the ice bin:
Pull the covering panel out from the bottom and then slide it
1.
back toward the rear. Lift the wire shutoff arm so it clicks into the OFF (up) position.
2.
Ice can still be dispensed, but no more can be made. Lift up the front of the storage bin and pull it out.
3.
Replace the bin by pushing it in all the way or the dispenser
4.
will not work. Push the wire shutoff arm down to the ON position to restart ice production. Make sure the door is closed tightly.
To care for ice storage bin:
Empty the ice bin. Use warm water to melt the ice if
1.
necessary.
Never use anything sharp to break up the ice in the
NOTE:
bin. This can cause damage to the ice container and the dispenser mechanism.
Wash ice bin with a mild detergent, rinse well and dry
2.
thoroughly. Do not use harsh or abrasive cleaners or solvents.
REMEMBER:
Allow 24 hours to produce the first batch of ice.
Discard the first three batches of ice produced to avoid impurities that may be flushed out of the system.
The quality of your ice will be only as good as the quality of the water supplied to your ice maker.
Avoid connecting the ice maker to a softened water supply. Water softener chemicals (such as salt) can damage parts of the ice maker and lead to poor quality ice. If a softened water supply cannot be avoided, make sure the water softener is operating properly and is well maintained.
It is normal for the ice cubes to be attached at the corners. They will break apart easily.
Do not force the wire shutoff arm up or down.
Do not store anything on top of the ice maker or in the ice storage bin.
12
REFRIGERATOR
FEATURES
Your model may have some or all of these features. Features that can be purchased separately as product accessories are labeled with the word “Accessory. Not all accessories will fit all models. If you are interested in purchasing one of the accessories, please call the toll-free number on the cover or in the “Accessories” section.
Important information to know about glass shelves and covers:
Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. For your protection, tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use special care when re­moving them to avoid impact from dropping.

Refrigerator Shelves

Your model may have glass or wire shelves. Store similar foods together and adjust the shelves to fit different heights. This reduces the time the refrigerator door is open and saves energy.

Flip-up Shelf

(on some models)
To raise or lower the shelf:
Raise the shelf by pulling forward on the lever located at the
1.
bottom front of the shelf and lift until the shelf locks into the vertical position.
Lower the shelf until it is latched securely in place.
2.

Adjustable Flip-up Shelf

(on some models)
To raise or lower the shelf:
Raise the shelf by first sliding it back and down to make it
1.
half-width. (You can use the shelf in this position to allow taller items to be stored on the shelf below.)
Lift the front of the shelf until it fits securely in place against
2.
the back wall. Lower the shelf securely back into position. Pull the front of the shelf forward until it fits into place.
3.
Slide-out Shelves (on some models)
To remove and replace a shelf in a metal frame:
Pull the shelf forward to the stop. Tilt the front of the shelf up
1.
and lift it slightly as you pull the shelf from the frame. Replace the shelf by guiding it back into the slots on the
2.
frame and pushing the shelf in past the stop.
Shelves and Shelf Frames
To remove and replace a shelf/frame:
Remove the shelf/frame by tilting it up at the front and lifting it
1.
out of the shelf supports. Replace the shelf/frame by guiding the rear shelf hooks into
2.
the shelf supports. Tilt the front of the shelf up until rear shelf hooks drop into the shelf supports. Check to make sure that the shelf is securely in position.

Deli Drawer

(on some models)
The deli drawer stores raisins, nuts, spreads, and other small items at normal refrigerator temperatures.
To remove and replace the deli drawer:
Remove the deli drawer by sliding it straight out to the stop.
1.
Lift the front and slide the drawer out the rest of the way. Replace the deli drawer by sliding it back past the stop.
2.
13
Convertible Vegetable/Meat Drawer, Crisper
and Covers
(on some models)
Crisper and Convertible Vegetable Meat Drawers
To remove and replace drawers:
Slide crisper or meat drawer straight out to the stop. Lift the
1.
front of drawer with one hand while supporting the bottom of drawer with other hand and slide the drawer out the rest of the way.
Replace the crisper or meat drawer by sliding it back in fully
2.
past the drawer stop.
Crisper or Vegetable/Meat Drawer Covers
To remove and replace covers:
Remove the crisper and meat drawer. Press up in center of
1.
crisper glass insert until it rises above the plastic frame. Holding the crisper glass firmly, carefully slide the glass insert forward to remove.
Lift crisper cover frame and remove. Repeat steps to remove
2.
the meat drawer cover.
Replace back of meat drawer cover frame into supports or
3.
slides on side walls of the refrigerator and lower or slide the front of the cover frame into place.
Slide rear of glass insert into cover frame and lower front into
4.
place. Repeat steps to replace the crisper cover.
Meat storage guide
Store most meat in original wrapping as long as it is airtight and moisture-proof. Rewrap if necessary. See the following chart for storage times. When storing meat longer than the times given, freeze the meat.
Fresh fish or shellfish..................use same day as purchased
Chicken, ground beef, variety meat (liver, etc.) .........1-2 days
Cold cuts, steaks/roasts ...........................................3-5 days
Cured meats............................................................7-10 days
Leftovers - Cover leftovers with plastic wrap, aluminum foil, or plastic containers with tight lids.

Crisper Humidity Control

(on some models)
You can control the amount of humidity in the moisture-sealed crisper. Adjust the control to any setting between LOW and HIGH.
LOW (open) lets moist air out of the crisper for best storage of fruits and vegetables with skins.
Fruit: Wash, let dry and store in refrigerator in plastic bag or crisper. Do not wash or hull berries until they are ready to use. Sort and keep berries in original container in crisper, or store in a loosely closed paper bag on a refrigerator shelf.
Vegetables with skins: Place in plastic bag or plastic container and store in crisper.
HIGH (closed) keeps moist air in the crisper for best storage of fresh, leafy vegetables.
Leafy vegetables: Wash in cold water, drain and trim or tear off bruised and discolored areas. Place in plastic bag or plastic container and store in crisper.
Humidity control location:
Humidity Control on crisper drawer (
Humidity Control on crisper cover (
Style 2
Style 1
- on left)
- on right)
Convertible Vegetable/Meat Drawer
Temperature Control
The convertible vegetable/meat drawer can be adjusted to properly chill meats or vegetables. The air inside the pan is cooled to prevent “spot” freezing and can be set to keep meats at the National Livestock and Meat Board recommended storage temperatures of 28°- 32°F (-2°- 0°C).
IMPORTANT:
moisture-proof materials before storing. Always store meat as recommended.
Adjusting the control
The convertible control comes preset at the lowest meat setting.
To change a control setting:
(colder) or to the left (less cold) as desired.
To store vegetables:
left) to store vegetables at their optimal storage temperatures (which need to be warmer than those for meat).
IMPORTANT:
(less cold). Remember to wait 24 hours between adjustments. Doing so gives the temperature of the food time to change.
To extend freshness, wrap meats in airtight,
Move the control to the right
Set the control to VEG (all the way to the
If food starts to freeze, move the control to the left

Wine or Can/Bottle Rack

(on some models - Accessory)
To remove and replace the wine rack (left) or can/bottle rack (right):
Remove the rack by pulling it straight out from the shelf.
1.
Replace the rack by sliding it in between the shelf and the
2.
wall of the refrigerator.

Utility Bin

(on some models - Accessory)
For long-term storage, place eggs in a covered container
NOTE:
or in their original carton on an interior shelf.
14

FREEZER FEATURES

DOOR FEATURES

Your model may have some or all of these features. Features that can be purchased separately as product accessories are labeled with the word “Accessory. Not all accessories will fit all models. If you are interested in purchasing one of the accessories, please call the toll-free number on the cover or in the “Accessories” section.
Freezer Shelf
(number of shelves varies with model)
To remove and replace the shelf:
Lift the shelf off of the supports.
1.
Slide it out of the shelf support holes.
2.
Replace shelf in the reverse order.
3.
Frozen food storage guide
Storage times will vary according to the quality and type of food, the type of packaging or wrap used (should be airtight and moisture-proof), and the storage temperature. Ice crystals inside a sealed package are normal. This simply means that moisture in the food and air inside the package have condensed, creating ice crystals.
Put no more unfrozen food into the freezer than will freeze within 24 hours (no more than 2 to 3 lbs. of food per cubic foot [907-1,350 g per L] of freezer space). Leave enough space in the freezer for air to circulate around packages. Be careful to leave enough room for the door to close tightly.
For more information on preparing food for freezing, check a freezer guide or reliable cookbook.
Your model may have some or all of these features. Features that can be purchased separately as product accessories are labeled with the word “Accessory.” Not all accessories will fit all models. If you are interested in purchasing one of the accessories, please call the toll-free number on the cover or in the “Accessories” section.
Door Rails
The door rails may be removed for easier cleaning.
Snap-on Door Rails
To remove and replace the rails:
Remove the rails by pushing in slightly on the front of the
1.
bracket while pulling out on the inside tab. Repeat these steps for the other end of the rail.
Replace the rails by aligning the ends of the brackets with the
2.
buttons on the sides of the door liner. Firmly snap bracket and rail assembly onto the tabs above the shelf as shown.
Drop-in Door Rails
To remove and replace the rails:
Remove the rails by pulling straight up on each end of the rail.
1.
Replace the rails by sliding the shelf rail into the slots on the
2.
door and pushing the rail straight down until it stops.
Freezer Basket or Bin
(plastic bin on some models)
The freezer basket or bin can be used to store bags of frozen fruits and vegetables that may slide off freezer shelves.
To remove and replace the freezer basket or bin:
Remove basket or bin by sliding it out to the stop.
1.
Lift the front of the basket or bin and slide it out the rest of the
2.
way.
Replace the basket or bin by positioning it on the side wall
3.
guide rails. Lift the basket or bin front slightly while pushing it past the guide rail stops and slide basket or bin in the rest of the way.
Can Racks and Door Bins
(on some models)
Can racks may be purchased as an Accessory for some
NOTE:
models.
To remove and replace the racks/bins:
Remove the rack/bin by lifting it and pulling it straight out.
1.
Replace the rack/bin by sliding it in above the desired
2.
support and pushing it down until it stops.
15
Loading...
+ 33 hidden pages