Whirlpool ARL 366/H, ARL 352/G/E, GSXP 7727 INSTRUCTION FOR USE
Before using the dishwasher, read the user instructions!
GSXP 7727
On button
Off button
Programme selection button
The selected programme is shown in the
window of the display.
Start button
Switches “on” when the dishwasher is
operating. Flashes when a fault occurs.
Switches off at the end of the programme.
Reset button
After pressing the Reset button, the selected
programme and the supplementary functions
are cancelled (except the detergent and water
hardness settings, see user instructions) and
must be reset. On releasing the button this is
confirmed by an acoustic signal.
Indicators
Add rinse aid
Add regeneration salt
Only add regeneration salt immediately
before starting a wash programme.
Programmes Loading instructions A B
Quick Reference Guide
Programme chart
Options
GB
3)
Time and failure display
Indicates in hours the time remaining until the start of
the wash cycle. Toward the end of the programme,
during the drying cycle, the display will indicate the time
remaining in minutes.
“F....” Identification of faults for service technician
“Delayed start” button
The wash cycle can be programmed to start after 1 - 24
hours. With each successive touch of the button, the
delayed start indicator increases by 1 hour, and after 24
returns to 00. Then press the Start button. The
dishwasher will start at the set time.
“Half load - Multizone” button
Load the upper or lower rack only.
This function can be used with any programme.
Press once = upper rack
(the indication lamp/symbol comes on)
Press twice = lower rack
(the indication lamp/symbol comes on)
Press 3 times = Off (half load function deactivated).
When washing without the top rack, press the “Half
Load” button twice, or “Lower rack wash” (the
corresponding LED/symbol comes on).
Set detergent
(when the appliance is used for the first time and when
using a different type of detergent)
Off indicator = detergent (powder, gel, tablets)
Left indicator =2 in 1 detergent
Right indicator = 3 in 1 / 4 in 1 detergent
Antibacterial rinse
This function adds an antibacterial rinse at the end of the
wash cycle, thereby guaranteeing a perfectly clean and
sanitized load. The lamp will light up when the function
is activated. If the temperature is not maintained during
the antibacterial cycle (e.g. if the door is opened and
remains open for a long time), the lamp will start
blinking to indicate that sanitation is not guaranteed.
Detergent
2)
Litres kWh Minutes
4) 5)
Consumption
3)
Pre-Rinse cold
Glass 40°C
Quickwash 40°C
1) 5) 6)
Bio
Standard
Intensive
1) Reference programme for energy label EN 50242;
2) Refer to “User instructions”;
3) Programme data obtained in conformity with European
standard EN 50242. Values may vary in relation to usage,
e.g.: different loads, options, water temperatures - above
or below 15°C - as well as water hardness and power
supply voltage, etc.
Important information for Test Laboratories:
For detailed information on the EN comparison test and other tests, contact the following address:
“nk_customer@whirlpool.com”.
5)
5)
50°C
60°C
70°C
Crockery to be washed later. - - 4.0 0.03 14
Light soiling, for example glasses
and cups.
Lightly soiled crockery with no
dried-on food.
X - 10.0 0.85 100
X - 10.0 0.65 30
Normally soiled crockery. X X 13.0 1.05 195
Normally or heavily soiled
crockery.
X X 13.0 1.25 120
Recommended programme for
heavily soiled crockery, especially
X X 14.0 1.55 155
suitable for pans and saucepans.
4) The bacteria removal efficiency has been tested by the
Institut Pasteur de Lille (France), based on the NF
EN 13697 standard of November 2001.
5) These programmes can be used with the Antibacterial
rinse option.
6) Energy saving programme with prolonged drying cycle.
(We reserve the right to make technical modifications)
5019 496 90469
How to use the appliance
ABC
Further indications are given in the single chapters and in the user instructions.
Switch on the appliance
Select, save, and
supply the detergent
Check the rinse aid level
Check the
regeneration salt level
Load the racks
Press the ON / OFF button.
(The first time you use the appliance
and when using a different type of
detergent)
1. Select the third programme from the
top in the relative table.
2. Press the Start button for about 7
seconds until the display changes.
3. Select the required detergent with
the Start button (OFF = powder
detergent, 2 in 1, 3in1, 4 in 1) (shown on the display).
4. Switch the appliance off and then switch it on again. The selected
detergent type will be shown on the display for approximately 3
seconds after switching on.
For dosage of powder detergent in compartment A and B refer to the
programmes table.
Mechanical indicator lamp C.
Electric indicator on control panel (if provided).
On models with water softener
system only.
Mechanical indicator lamp D. Electric
indicator on control panel (if provided).
Refer to the dishwasher loading instructions.
Close the dishwasher door,
turn on the water tap
Select a programme
Select additional options
Press the Start button
Wash cycle
Switch off the appliance
Turn off the water tap,
unload the racks
The last programme selected will light up.
Select the desired programme (using the specific button or knob).
The corresponding indicator lamp lights up.
If necessary (and if provided).
The corresponding indicator lamp lights up.
The selected programme is
then memorised (even in the
event of power failure).
Only after the START button has switched off: Press the ON /
All the indicator lamps switch off.
Warning: When the door is opened steam comes out!
Unload the appliance, starting from the lower rack.
“Change programme in progress”
Press the START button for 2 sec. until the
Start indicator lamp switches off.
Select another programme and press the
START button again.
- Only open the dishwasher if necessary
(Warning: beware of hot steam).
- If the appliance is switched off during a
wash cycle, when switched on again it
will resume the cycle from where it was
interrupted.
OFF
button.
Loading...