Whirlpool GSXP 7427 INSTRUCTION FOR USE

Before using the dishwasher, read the user instructions!

GSXP 7427

On button

Off button

Programme selection button

The selected programme is shown in the
window of the display.

Start button

Switches “on” when the dishwasher is
operating. Flashes when a fault occurs.
Switches off at the end of the programme.

Reset button

After pressing the Reset button, the selected
programme and the supplementary functions
are cancelled (except the detergent and water
hardness settings, see user instructions) and
must be reset. On releasing the button this is
confirmed by an acoustic signal.

Indicators

Add rinse aid

Add regeneration salt

Only add regeneration salt immediately
before starting a wash programme.

Programmes Loading instructions A B

Quick Reference Guide

Programme chart

Options

GB

3)

Time and failure display

Indicates in hours the time remaining until the
start of the wash cycle. Toward the end of the
programme, during the drying cycle, the display
will indicate the time remaining in minutes.

“F....” Identification of faults for service

technician

“Delayed start” button

The wash cycle can be programmed to start
after 1 - 24 hours. With each successive touch of
the button, the delayed start indicator increases
by 1 hour , and after 24 returns to 00. Then press
the Start button. The dishwasher will start at the
set time.

“Half load - Multizone” button

Load the upper or lower rack
This function can be used with any programme.
Press once = upper rack
(the indication lamp/symbol comes on)
Press twice = lower rack
(the indication lamp/symbol comes on)
Press 3 times = Off (half load function
deactivated).
When washing without the top rack, press the
“Half Load” button twice, or “Lower rack wash”
(the corresponding LED/symbol comes on).

Set detergent

(when the appliance is used for the first time and
when using a different type of detergent)
Off indicator = detergent (powder, gel, tablets)
Left indicator =2 in 1 detergent
Right indicator = 3 in 1 / 4 in 1 detergent

Antibacterial rinse

This function adds an antibacterial rinse at the end
of the wash cycle, thereby guaranteeing a perfectly
clean and sanitized load. The lamp will light up
when the function is activated. If the temperature
is not maintained during the antibacterial cycle (e.g.
if the door is opened and remains open for a long
time), the lamp will start blinking to indicate that
sanitation is not guaranteed.

Detergent

2)

Consumption

Litres kWh Minutes

4) 5)

only

.

3)

Pre-Rinse cold

Quickwash 40°C

1) 5) 6)

Bio

Intensive

1) Reference programme for energy label EN 50242;

2) Refer to “User instructions”;

3) Programme data obtained in conformity with European
standard EN 50242. Values may vary in relation to usage,
e.g.: different loads, options, water temperatures - above
or below 15°C - as well as water hardness and power
supply voltage, etc.

Important information for Test Laboratories:
For detailed information on the EN comparison test and other tests, contact the following address:
“[e-mail]”.

5)

50°C

70°C

Crockery to be washed later. - - 4.0 0.03 14

Lightly soiled crockery with no
dried-on food.

Normally soiled crockery. X X 13.0 1.05 195
Recommended programme for

heavily soiled crockery, especially
suitable for pans and saucepans.

4) The bacteria removal efficiency has been tested by the
Institut Pasteur de Lille (France), based on the NF
EN 13697 standard of November 2001.

5) These programmes can be used with the Antibacterial
rinse option.

6) Energy saving programme with prolonged drying cycle.

(We reserve the right to make technical modifications)

X - 10.0 0.65 30

X X 14.0 1.55 155

5019 496 90470

How to use the appliance

ABC

Further indications are given in the single chapters and in the user instructions.

Switch on the appliance

Select, save, and

supply the detergent

Check the rinse aid level

Check the

regeneration salt level

Load the racks

Press the ON / OFF button.

(The first time you use the appliance
and when using a different type of
detergent)

1. Select the third programme from the
top in the relative table.

2. Press the Start button for about 7
seconds until the display changes.

3. Select the required detergent with
the Start button (OFF = powder
detergent, 2 in 1, 3in1, 4 in 1) (shown on the display).

4. Switch the appliance off and then switch it on again. The selected
detergent type will be shown on the display for approximately 3
seconds after switching on.

For dosage of powder detergent in compartment A and B refer to the
programmes table.

Mechanical indicator lamp C.
Electric indicator on control panel (if provided).

On models with water softener
system only.

Mechanical indicator lamp D. Electric
indicator on control panel (if provided).

Refer to the dishwasher loading instructions.

Close the dishwasher door,

turn on the water tap

Select a programme

Select additional options

Press the Start button

Wash cycle

Switch off the appliance

Turn off the water tap,

unload the racks

The last programme selected will light up.
Select the desired programme (using the specific button or knob).
The corresponding indicator lamp lights up.

If necessary (and if provided).
The corresponding indicator lamp lights up.

The selected programme is
then memorised (even in the
event of power failure).

Only after the START button has switched off: Press the ON /
All the indicator lamps switch off.

Warning: When the door is opened steam comes out!

Unload the appliance, starting from the lower rack.

“Change programme in progress”

Press the START button for 2 sec. until the
Start indicator lamp switches off.

Select another programme and press the
START button again.

- Only open the dishwasher if necessary
(Warning: beware of hot steam).

- If the appliance is switched off during a
wash cycle, when switched on again it
will resume the cycle from where it was
interrupted.

OFF

button.