Whirlpool GSUK 61202 DI A IN INSTRUCTION FOR USE
CANCEL/OFF BUTTON
Push this button to switch off the control panel.
If pressed when a program is running it cancels the
program ongoing draining water for 1 minute
(0:01 is shown into the display).
If pressed when the dishwasher is switched off,
it drains any possible liquids from dishwasher
(1 minute process).
PROGRAM SELECTION
BUTTON
Push “P” button (repeatedly)
until selected program number
is shown on the display
(P1...Px) - see “Table of
programs” below.
START/RESUME BUTTON
Push this button to start the selected program: the
indicator lights up and goes off at the end of the program.
When the door is opened during a washing cycle,
the cycle is temporarily paused: the Start indicator
blinks. To resume the cycle close the door and
push Start button again.
(see at right for options description)
1) Program data obtained in conformity with European standard EN 50242, obtained under normal conditions (without additional options) and may
vary depending on conditions. Differences of up to 20 minutes are possible with sensor programs as a result of the appliance’s automatic
calibration system.
2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the EN/
Standard loading comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.
Table of programs
Deter-
gent
Consumption
Drying
Phase
Programs
Available
options
Loading instructions
Litres kWh
Minutes
1)
P1
Sensor 40°-70°C
Delay
Half load
Recommended program for
routine washes, with dried-on
food (e.g. EN 50242).
X 7-14 1.00-1.60 70-155 Full
P2
Pre-Wash cold
Delay Crockery to be washed later. — 4.0 0.03 14 NO
P3
Rapid 45°C
Delay
Lightly soiled crockery , with
no dried-on food.
X 11.0 0.80 30 NO
P4
Eco
2)
50°C
Delay
Half load
Normally soiled crockery.
Energy-saving program.
X 11.5 1.03 170 Full
P5
Fast Daily 60°C
Delay
Half load
Normally soiled crockery. X 10.0 1.30 80 Full
P6
Steam
Delay
Program including steam
action dedicated for heavily
soiled crockery, pots and
pans. Soaking or hand
pretreatment is no longer
needed.
X 14.0 1.70 180 Full
5019 496 01737
Options and display description
SALT INDICATOR
When lit (at the end of the cycle),
the salt reservoir needs to be
refilled.
HALF LOAD BUTTON
Half load cycle can be used for the upper or lower rack.
Select the required program then press the “Half Load”
button - the light comes on. Turns off at the en d of the
program.
The “Half Load” option can be used with the
programs indicated in the table of programs.
TABLET SETTING
This setting allows to optimize the
cycle performances according the
type of detergent used.
Push the Tablet button for
3 seconds (until the indicator lights
up) if you are using the combined
detergents in tablet (rinse aid, salt
and detergent in 1 dose).
If you are using powder detergent
or liquid detergent, the Tablet
indicator on the control panel has to
be off.
RINSE AID INDICATOR
When lit (at the end of the cycle),
the rinse aid dispenser needs to
be refilled.
BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS
QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTR UCTIONS!
THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING ANY
BUTTON EXCEPT CANCEL/OFF BUTTON.
FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES
AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED.
DELAYED START BUTTON
Push the button (repeatedly) to delay the
start of the program - delay indicator
turns on. Adjustable from 1 to 24 hours.
With each press of the button, the delay
increases by one hour and after "h 24”
returns to "h 00”. When this option is
selected the delay indicator turns on.
Then press the START button. The
dishwasher will start after the set time.
WASH TIME DISPLAY
Indicated the cycle duration and the remaining time (h:min). With “Delayed start” selected it indicates
the time remaining until program start (h.00) - below 1h (0:min).
If “Fx Ey” messages appears on the display, see page 6 - chapter “What to do if...”.
Quick reference guide
Chart
Bauknecht is a registered trademark
GB -1-
1
4
10
9
23
5
7
86
1- salt reservoir
2- rinse aid dispenser
3- detergent dispenser
4- racks system
5,6,7,8- available functions on the panel
9- filters
10- spray arms
Water hardness should be set only
before the first wash or if water
hardness has been changed
(depending on the model)
The salt level indicator lamp may rem ai n lit
at the end of several wash cycles. If the
water hardness level falls with in category
(soft), no salt is required.
Salt indicator on the control pa ne l Salt indicator on the salt reservoir cap
The indicator lamp lights up when
SALT NEEDS TO BE ADDED.
green: OK.
clear: NEEDS TO
BE ADDED
- Press and hold together PROGRAM Selection and CANCEL/Off buttons for minimum 3 seconds.
- The current water hardness setting will be visible on the display.
- Press the PROGRAM Selection button to increase setting. Value range goes from 1 to 7 (when the level reaches 7, the next
press of the start button will set the leve l back to 1).
- Wait 30 seconds (control panel switches off) or press Start/Resume button to save setting.
1. Ask your water supply company what the water hardness is... 2. ...enter this value on
your dishwasher
Suggestions for detergent use
German
degrees °dH
French
degrees °fH
English
degrees °eH
Water har dness
level
Insert value is shown
in the display
Gel or Powder
(rinse aid and salt)
Tablets
0 - 5 0 - 9 0 - 6.3 Soft 1
go to step 1
(see “Daily
check”)
6 - 10 10 - 18 7 - 12.6 Medium 2
11 - 15 19 - 27 13.3 - 18.9 Average 3
16 - 21 28 - 37 19.6 - 25.9 Medium-hard 4
if water is
HARD extra salt
needs to be added
(go to step 1,
“Daily check”)
22 - 28 38 - 50 26.6 - 35 Hard 5
29 - 35 51 - 63 35.7 - 44.1 Ve ry hard 6
36 - 50 64 - 90 44.8 - 62.4 Extremely hard 7
1
Visual indicator
(depending
on the model).
Unscrew cap.
Daily check
Filling the salt reservoir - Dissolve limescale (not necessary if water hardness level is set to “soft”!)
Screw on the cap.
Salt residual
around the cap
need to be
removed. Some
salt reservoir have
a level indicator
integrated in the
cap (see below
how to check).
At first time use, the salt
reservoir has to be filled
independently from water
hardness level (see
description below in step 1
“Daily check”).
Water hardness level is factory
set for medium-hard water
(level 4).
Even if you use tablets which
include salt functionality, you
must still add regeneration salt
since such detergents are not
effective enough at softening
hard water.
Once regeneration salt is added, immediately start a wash program (the “Pre-wash” program alone is not sufficient). Residual saline solution or grains of salt can lead to
deep-down corrosion, irreparably damaging the stainless steel components. The guarantee is not applicable if fa ults are caused by such circumstances.
Fill the salt reservoir with water
before the first wash only.
Add salt (never add detergent!)
min. 0.8 kg / max. 1 kg
How to set water hardness in order to always assure the best cleaning results
First time use
GB -2-
3
Check the rinse aid indicator to check the level
into the dispenser.
(depending on the model)
Rinse aid indicator on the control panel Rinse aid indicator on the dispenser
The indicator lamp lights up when RINS E AID NEEDS
TO BE ADDED.
dark: OK. clear: NEEDS TO BE ADDED
Only use rinse aids recommended for use in domestic dishwashers. Immediately wipe away any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause a fault function of the
appliance.
If there are streaks: reduce the dosage by turning t he dial to a lower setti ng (1-3). If crockery is not perfectly dry: increase th e dosage by turning the dial to a higher setting (5- 6). Plastic di shes have more diff iculty
drying and a higher rinse aid setting will not improve the situation.
Detergents with rinse aid incorporated may be effective only with longer programs. In the case of shorter programs, detergent residue may be a problem (if necessary, use powder detergent). Detergents with
rinse aid incorporated tend to form excess suds.
Daily use
Adding detergent - Use only detergent specifically for dishwashers in accordance with the supplier’s recommendations
Open the cover A
(press the dedicated button).
Only fill the
detergent dispenser
prior to starting a
wash program.
Shut the cover
by pressing dedicated ribs.
If required,
open the
cover B
(press the
dedicated
button).
Add rinse aid
to the max.
line ~150 ml
The rinse aid dosage can be
adjusted to the detergent used.
The lower the setting, the less
rinse aid is dispensed (factory
setting: position 4).
Press the button to open the
cover B. Using a coin or similar
object, turn the arrow to the
desired setting. After adjusting
the rinse aid setting, shut the
cover again.
Visual
indicator
2
Use only one tablet per one cycle, only
placed in detergent dispenser.
All types of tablets can be used, but for
2 in 1 type adding of salt is mandatory.
Some type of tablets could not dissolve
completely during the short programs
(Rapid, Fragile, Handwash); placing the
tablet on the tub bottom can help
dissolving and washing.
Insert detergent: Tablet / powder / liquid into the big chamber.
Please look for the recommendation of the detergent manufacturer
on the packaging of the detergent product.
Adding rinse aid (not necessary when you use tablets). How to adjust the rinse aid dosage regulator
Daily check
GB -3-
Loading...