Whirlpool GSIP 81312 TR A PT INSTRUCTION FOR USE
Quick reference guide
Chart
BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!
THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING ANY BUTTON EXCEPT CANCEL/OFF BUTTON.
FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED.
WASH TIME DISPLAY
Indicated the cycle duration and the remaining time (h:min). With “Delayed start” selected it
indicates the time remaining until program start (h.00) - below 1h (0:min).
If “Fx Ey” messages appears on the display, see page 9 - chapter
“What to do if...”.
PROGRAM
SELECTION
BUTTON
Push “P” button
(repeatedly) until selected
program number is shown
on the display (P1...Px) see “Table of programs” next page).
POWER CLEAN
Thanks to the additional
power jets this option
provides a more intensive
and powerful wash in the
lower rack, in the specific
area. This option is
recommended for
washing pots and
casseroles (see page 7).
Press this button to
activate Power Clean
(the indicator lights up).
For non Power Clean
loading to achieve best
cleaning performances
and resources
optimization, Power
Clean should be switched
off.
ANTIBACTERIAL
3)
RINSE
This function activates an
antibacterial rinse at the
end of the wash cycle,
guaranteeing a further
reduction of bacteria.
Press the button to
activate or deactivate the
function.
This function can be used
with the programs
indicated in the table of
programs. The
dishwasher door must be
kept shut for the entire
duration of the program in
order to guarantee
reduction of bacteria.
If the door is opened the
indicator lamp starts
flashing.
TABLET SETTING
This setting allows to
optimize the cycle
performances according
the type of detergent
used. Push the Tablet
button for 3 seconds (until
the indicator lights up)
if you are using the
combined detergents in
tablet (rinse aid, salt and
deteregent in 1 dose).
If you are using powder
detergent or liquid
detergent, the Tablet
indicator on the control
panel has to be off.
RINSE AID INDICATOR
When lit (at the end of the
cycle), the rinse aid dispenser
needs to be refilled.
DELAYED START
BUTTON
Push the button
(repeatedly) to delay the
start of the program.
Adjustable from 1 to 24
hours. With each press of
the button, the delayed
start indicator increases
by one hour and after
24 restarts from 0.
Then press the START
button. The dishwasher
will start after the set
time.
SALT INDICATOR
When lit (at the end of the
cycle), the salt reservoir needs
to be refilled.
START/RESUME
BUTTON
Push this button to start
the selected program: the
indicator lights up and
goes off at the end of the
program.
When the door is opened
during a washing cycle, the
cycle is temporarily
paused: the Start indicator
blinks.
To resume the cycle close
the door and push Start
button again.
5019 496 01782
CANCEL/OFF
BUTTON
Push this button to switch
off the control panel.
If pressed when a
program is running it
cancels the program
ongoing draining water for
1 minute (0:01 is shown
into the display).
If pressed when the
dishwasher is switched
off, it drains any possible
liquids from dishwasher
(1 minute process).
Bauknecht is a registered trademark
GB -1-
Quick reference guide
Chart
Table of programs
Deter-
Programs
P1
P2
P3
P4
P5
P6
P7
P8
1) Program data obtained in conformity with European standard EN 50242, obtained under normal conditions (without any options) and may vary depending on conditions. Differences of up to
20 minutes are possible with sensor programs as a result of the appliance’s automatic calibration system.
2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the EN/Standard loading comparison test and other tests,
contact the following address: “nk_customer@whirlpool.com”.
3) The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 standard of November 2001.
RECYCLING WATER SYSTEM: these programs save water in a dedicated tank.
A TANK CLEANING CYCLE (at least 45 min.) is automatically run every 30 cycles or after every power off, to assure the best product conditions.
Sensor Power
Clean Plus
Pre-Wash cold
Glass 40°C
Express 45°C
2)
Eco
Normal 60°C
Night 39dBA 50°C
All in 1
40°-70°C
50°C
Available
options
Delay
Power Clean
Antibacterial
Rinse
Delay Crockery to be washed later.
Delay Light soiling, for example glasses and cups.
Delay Lightly soiled crockery, with no dried-on food.
Delay
Power Clean
Antibacterial
Rinse
Delay
Antibacterial
Rinse
Delay
Delay
Power Clean
Antibacterial
Rinse
Use for normal soiled dishes with dried-on food. Senses the level
of soiling on the dishes and adjusts the program accordingly.
When the sensor is detecting the soil level an animation appears
in the display and the cycle duration is updated. The Power
Clean option is activated automatically with this program. To
deactivate, press the Power Clean button on the control panel.
Normally soiled crockery. Energy-saving program.
Normally soiled crockery.
Normally soiled crockery, gentle and quiet thanks to the
lower spray pressure.
This program is able to manage different wash intensity for
each rack. You can optimize loading and properly wash
different crockery in one cycle, loading delicate items in
upper rack and pots and pans in lower rack.
Loading instructions Litres kWh
gent
X 7-14 1.00-1.65 80-165 Full
— 4.0 0.03 14 NO
X 10.0 0.85 100 Light
X 11.0 0.80 30 NO
X 6.0 1.03 185 Full
X 10.0 1.30 80 Full
X 10.0 1.20 290 Light
X 11.0 1.35 155 Full
Consumption
Minutes
1)
Drying
Phase
GB -2-
How to set water hardness in order to always assure the best cleaning results
First time use
10
1
23
5
7
1- salt reservoir
2- rinse aid dispenser
3- detergent dispenser
4- racks system
5,6,7,8- available functions on the panel
9- filters
10- spray arms
86
Water hardness should be set
only before the first wash or if
water hardness has been
changed
Water hardness level is
factory set for medium-hard
water (level 4).
Even if you use tablets which
include salt functionality, you
must still add regeneration
salt since such detergents are
not effective enough at
softening hard water.
At first time use, the salt
4
9
reservoir has to be filled
independently from water
hardness level (see
description below in step 1
“Daily check”).
- Press and hold together PROGRAM Selection and CANCEL/Off buttons for minimum 3 seconds.
- The current water hardness setting will be visible on the display.
- Press the PROGRAM Selection button to increase setting. Value range goes from 1 to 7 (when the level reaches 7, the
next press of the start button will set the level back to 1).
- Wait 30 seconds (control panel switches off) or press Start/Resume button to save setting.
1. Ask your water supply company what the water hardness is... 2. ...enter this value
German
degrees °dH
0 - 5 0 - 9 0 - 6.3 Soft 1
6 - 10 10 - 18 7 - 12.6 Medium 2
11 - 15 19 - 27 13.3 - 18.9 Average 3
16 - 21 28 - 37 19.6 - 25.9 Medium-hard 4
22 - 28 38 - 50 26.6 - 35 Hard 5
29 - 35 51 - 63 35.7 - 44.1 Very hard 6
36 - 50 64 - 90 44.8 - 62.4 Extremely hard 7
French
degrees °fH
English
degrees °eH
Water hardness
level
Filling the salt reservoir - Dissolve limescale (not necessary if water hardness level is set to “soft”!)
Visual indicator
1
Once regeneration salt is added, immediately start a wash program (the “Pre-wash” program alone is not sufficient).
Residual saline solution or grains of salt can lead to deep-down corrosion, irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such circumstances.
The salt level indicator lamp may remain lit
at the end of several wash cycles. If the
water hardness level falls within category
(soft), no salt is required.
(depending
on the model).
Unscrew cap.
Fill the salt reservoir with water
before the first wash only.
(depending on the model)
Salt indicator on the control panel Salt indicator on the salt reservoir cap
The indicator lamp lights up when SALT
NEEDS TO BE ADDED.
Add salt (never add detergent!)
min. 0.8 kg/max. 1 kg
on your dishwasher
Insert value is shown
in the display
Suggestions for detergent use
Gel or Powder
(rinse aid and salt)
go to step 1
(see “Daily
check”)
Daily check
green: OK.
Tablets
if water is
HARD extra salt
needs to be
added
(go to step 1,
“Daily check”)
Screw on the cap.
Salt residual
around the cap
need to be
removed. Some
salt reservoir have
a level indicator
integrated in the
cap (see below
how to check).
clear: NEEDS TO
BE ADDED
GB -3-
Adding rinse aid (not necessary when you use tablets). How to adjust the rinse aid dosage regulator
Daily check
Visual
2
Check the rinse aid indicator to check the
level into the dispenser.
Only use rinse aids recommended for use in domestic dishwashers. Immediately wipe away any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause
a fault function of the appliance.
If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3). If crockery is not perfectly dry: increase the dosage by turning the dial to a higher setting (5-6).
Plastic dishes have more difficulty drying and a higher rinse aid setting will not improve the situation.
Detergents with rinse aid incorporated may be effective only with longer programs. In the case of shorter programs, detergent residue may be a problem (if necessary, use powder
detergent). Detergents with rinse aid incorporated tend to form excess suds.
Adding detergent - Use only detergent specifically for dishwashers in accordance with the supplier’s recommendations
Open the cover A
(press the dedicated button).
3
indicator
If required,
open the
cover B
(press the
dedicated
button).
Add rinse
aid to the
max. line
~150 ml
(depending on the model)
Rinse aid indicator on the control panel Rinse aid indicator on the dispenser
The indicator lamp lights up when
RINSE AID NEEDS TO BE ADDED.
Insert detergent: Tablet / powder / liquid into the big chamber.
Please look for the recommendation of the detergent manufacturer
Only fill the detergent
dispenser prior to
starting a wash
program.
on the packaging of the detergent product.
Use only one tablet per one cycle, only
placed in detergent dispenser.
All types of tablets can be used, but for
2 in 1 type adding of salt is mandatory.
Some types of tablets may not dissolve
completely during the short cycles (Glass,
Express, Handwash); placing the tablet
on the tub bottom can help dissolving and
washing.
The rinse aid dosage can be
adjusted to the detergent
used. The lower the setting,
the less rinse aid is dispensed
(factory setting: position 4).
Press the button to open the
cover B. Using a coin or
similar object, turn the arrow
to the desired setting. After
adjusting the rinse aid setting,
shut the cover again.
dark: OK. clear: NEEDS TO BE ADDED
Shut the cover
by pressing dedicated ribs.
Daily use
GB -4-
Loading...