Whirlpool GSIE 6598/1 IN INSTRUCTION FOR USE

GSIE 6598

Indicators

Programmes Loading instructions A B

Auto

Pre-Rinse cold

Before using the dishwasher, read the user instructions!

Quick Reference Guide

Options

Time and failure display

Programme selection button

On / Off button

Start button

Switches “on” when the dishwasher is

operating. Flashes when a fault occurs.
Switches off at the end of the programme.

Add regeneration salt

Only add regeneration salt immediately
before starting a wash programme.

Add rinse aid

Programme chart

5)

50-65°C

Automatic programme recommended
for routine washes, with dried-on food
(for example for EN 50242).

Crockery to be washed later. - - 4.0 0.03 14

Indicates in hours the time remaining until the
start of the wash cycle. Switches off when the
programme has started and indicates the time
remaining in hours and minutes.

“F ....” Information for the After -Sales Service

“Delayed start” button

The wash cycle can be programmed to start
after 1 - 24 hours. With each successive touch
of the button, the delayed start indicator
increases by 1 hour, and after 24 returns to

00.Then press the Start button. The
dishwasher will start at the set time.

“Half load - Multizone” button

Load the upper or lower rack
This function can be used with any programme.
Press once = upper rack (the indication lamp/
symbol comes on)
Press twice = lower rack (the indication lamp/
symbol comes on)
Press 3 times = Off (half load function deactivated).
When washing without the top rack, press the
“Half Load” button twice, or “Lower rack wash”
(the corresponding LED/symbol comes on).

Antibacterial rinse

This function adds an antibacterial rinse at
the end of the wash cycle, thereby
guaranteeing a perfectly clean and sanitized
load. The lamp will light up when the
function is activated. If the temperature is
not maintained during the antibacterial cycle
(e.g. if the door is opened and remains open
for a long time), the lamp will start blinking
to indicate that sanitation is not guaranteed.

3)

.

only

4)

Detergent

X X 11-16 1.1-1.5 100-130

2)

Consumption

Litres kWh Minutes

GB

3)

Rapid 30 min 40°C

Standard

Intensive

1) Reference programme for energy label EN 50242;

2) Refer to “User instructions”;

3) Program data obtained in conformity with European
standard EN 50242. Values may vary in relation to
usage, e.g.: different loads, water temperatures ­above or below 15°C - as well as water hardness and
power supply voltage, etc.

Important information for Test Laboratories:
For detailed information on the EN comparison test and other tests, contact the following address:
“[e-mail]”.

1) 5)

5)

Lightly soiled crockery with no dried­on food.

Normally soiled crockery. X X 14.0 1.05 145

50°C

Recommended programme for heavily
soiled crockery, especially suitable for

70°C

pans and saucepans.

4) The bacteria removal efficiency has been tested by
the Institut Pasteur de Lille (France), based on the NF
EN 13697 standard of November 2001.

5) These programmes can be used with the Antibacterial
rinse option.

(We reserve the right to make technical modifications)

X - 10.0 0.65 30

X X 15.0 1.70 150

5019 496 90416

How to use the appliance

CBA

Further indications are given in the single chapters and in the user instructions.

Switch on the appliance

How to fill the

detergent dispenser

Check the

rinse aid level

Check the regeneration

salt level

Load the racks

Close the door,

turn on the water tap

Select a programme

Press the ON/ OFF button.

Large compartment
With each wash cycle.
Small compartment
For programmes with pre-wash only.

Mechanical indicator C.
Electric indicator on control panel (if provided).

On models with water softener system only.

Mechanical indicator D.
Electric indicator on control panel (if provided).

Refer to the dishwasher loading instructions.

The last programme selected will light up.
Select the desired programme (using the specific button or
knob). The corresponding indicator lamp lights up.

A:

B:

Select additional

options

Press the START button

Wash cycle

Switch off the appliance

Shut off the water tap,

unload the racks

If necessary (and if provided) the corresponding indicator
lamp lights up.

The selected programme
is then memorised (even
in the event of power
failure).

Only after the START button has switched off: Press the
ON /

Warning: when the door is opened steam comes out!

Unload the appliance, starting from the lower rack.

button. All the indicator lamps switch off.

OFF

“Change programme”

Press the START button for 2 sec. until
the Start indicator lamp switches off;
Select another programme and
press the START button again.

- Only open the dishwasher if necessary
(Warning: beware of hot steam).

- If the appliance is switched of f during
a wash cycle, when switched on
again it will resume the cycle from
where it was interrupted.