Whirlpool GSF STUTTGART CLASSIC WS INSTRUCTION FOR USE

Before using the dishwasher, read the user instructions!

GSF Stuttgart

Programme selector knob

On / Off button

Quick Reference Guide

Options

Time and failure display

Indicates in hours the time remaining
until the start of the wash cycle.
Switches off at programme start and
indicates the remaining time in hours
and minutes.

“F...” Information for the
After-Sales Service

GB

3)

Start button

Switches “on” when the dishwasher

is operating. Flashes when a fault
occurs. Switches off at the end of
the programme.

Indicators

Add regeneration salt

Only add regeneration salt
immediately before starting a
wash programme.

Add rinse aid

Programme chart

Programmes Loading instructions A B

Pre-Rinse cold

Rapid 30 min 40°C

Standard

Normal 65°C

“Delayed start” button

The wash cycle can be programmed to
start after 1 - 24 hours. With each
successive touch of the button, the
delayed start indicator increases by
1 hour, and after 24 returns to 00.
Then press the Start button. The
dishwasher will start at the set time.

Detergent

Crockery to be washed
later.

Lightly soiled crockery
with no dried-on food.

1)

Normally soiled crockery. X X 16.0 1.05 120

50°C

Normally or heavily soiled
crockery.

- - 5.0 0.02 10

X - 13.0 0.70 30

X X 16.0 1.65 90

2)

Consumption

Litres kWh Minutes

3)

Intensive 70°C

1) Reference programme for energy label in
compliance with EN 50242 regulations;

2) Refer to “User instructions“;

Important information for Test Laboratories:
For detailed information on the EN comparison test and other tests, contact the following address:
“[e-mail]”.

Heavily soiled crockery,
especially pots and pans.

3) Program data obtained in conformity with

X X 17.0 1.90 125

European standard EN 50242. Values may vary in
relation to usage, e.g.: different loads, water
temperatures - above or below 15°C - as well as
water hardness and power supply voltage, etc.

(We reserve the right to make technical modifications)

5019 496 90279

How to use the appliance

C

BA

Further indications are given in the single chapters and in the user instructions.

Switch on the appliance

How to fill the

detergent dispenser

Check the

rinse aid level

Check the regeneration

salt level

Load the racks

Close the door,

turn on the water tap

Select a programme

Press the ON/ OFF button.

Large compartment
With each wash cycle.
Small compartment
For programmes with pre-wash only.

Mechanical indicator C.
Electric indicator on control panel (if provided).

On models with water softener system only.

Mechanical indicator D.
Electric indicator on control panel (if provided).

Refer to the dishwasher loading instructions.

The last programme selected will light up.
Select the desired programme (using the specific button or
knob). The corresponding indicator lamp lights up.

A:

B:

Select additional

options

Press the START button

Wash cycle

Switch off the appliance

Shut off the water tap,

unload the racks

If necessary (and if provided) the corresponding indicator
lamp lights up.

The selected programme
is then memorised (even
in the event of power
failure).

Only after the START button has switched off: Press the

OFF

ON /

Warning: when the door is opened steam comes out!

Unload the appliance, starting from the lower rack.

button. All the indicator lamps switch off.

“Change programme”

Press the START button for 2 sec. until
the Start indicator lamp switches off;

Select another programme and
press the START button again.

- Only open the dishwasher if necessary
(Warning: beware of hot steam).

- If the appliance is switched off during
a wash cycle, when switched on
again it will resume the cycle from
where it was interrupted.