Quick reference guide |
Chart |
BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!
THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING ANY BUTTON EXCEPT CANCEL/OFF BUTTON.
FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED.
WASH TIME DISPLAY |
|
RINSE AID INDICATOR |
|
SALT INDICATOR |
|
|
|
|
|||
Indicated the cycle duration and the remaining time (h:min). With “Delayed start” selected it |
|
When lit (at the end of the cycle), the |
|
When lit (at the end of the cycle), the |
|
|
|
|
|||
indicates the time remaining until program start (h.00) - below 1h (0:min). |
|
rinse aid dispenser needs to be refilled. |
|
salt reservoir needs to be refilled. |
5019 496 01745 |
||||||
If “Fx Ey” messages appears on the display, see page 9 - chapter “What to do if...”. |
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PROGRAM SELECTION BUTTON
Push “P” button (repeatedly) until selected program number is shown on the display (P1...Px) - see “Table of programs” next page.
DELAYED START BUTTON Push the button (repeatedly) to delay the start of the program - delay indicator turns on. Adjustable from 1 to 24 hours. With each press of the button, the delay increases by one hour and after "h 24" returns to
"h 00”. When this option is selected the delay indicator turns on. Then press the START button. The dishwasher will start after the set time.
HALF LOAD BUTTON
Half load cycle can be used for the upper or lower rack. Select the required program then press the “Half Load” button - the light comes on. Turns off at the end of the program.
The “Half Load” option can be used with the programs indicated in the table of programs.
TABLET SETTING
This setting allows to optimize the cycle performances according the type of detergent used. Push the Tablet button for 3 seconds (until the indicator lights up) if you are using the combined detergents in tablet (rinse aid, salt and deteregent in 1 dose). If you are using powder detergent or liquid detergent, the Tablet indicator on the control panel has to be off.
START/RESUME BUTTON Push this button to start the selected program: the indicator lights up and goes off at the end of the program.
When the door is opened during a washing cycle, the cycle is temporarily paused: the Start indicator blinks.
To resume the cycle close the door and push Start button again.
CANCEL/OFF BUTTON Push this button to switch off the control panel.
If pressed when a program is running it cancels the program ongoing draining water for
1 minute (0:01 is shown into the display).
If pressed when the dishwasher is switched off, it drains any possible liquids from dishwasher
(1 minute process).
GB -1-
|
Quick reference guide |
|
|
|
|
|
|
|
|
Chart |
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Table of programs |
|
Deter- |
|
Consumption |
Drying |
|
|||
|
|
|
|
|
|
|
|
|
|
|
||
|
|
Programs |
|
Available |
|
Loading instructions |
gent |
Litres |
kWh |
Minutes 1) |
Phase |
|
|
|
|
options |
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
P1 |
Sensor |
40°-70°C |
Delay |
|
Recommended program for routine |
|
|
|
|
|
|
|
|
washes, with dried-on food |
X |
7-14 |
1.00-1.65 |
80-165 |
Full |
|
||||
|
|
|
|
Half Load |
|
(e.g. EN 50242). |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
P2 |
Pre-Wash |
cold |
Delay |
|
Crockery to be washed later. |
— |
4.0 |
0.03 |
14 |
NO |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
P3 |
Rapid |
45°C |
Delay |
|
Lightly soiled crockery, with no dried-on |
X |
11.0 |
0.80 |
30 |
NO |
|
|
|
food. |
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
P4 |
Eco 2) |
50°C |
Delay |
|
Normally soiled crockery. |
X |
11.5 |
1.03 |
150 |
Full |
|
|
Half Load |
|
Energy-saving program. |
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
P5 |
Fast Daily |
60°C |
Delay |
|
Normally soiled crockery. |
X |
10.0 |
1.30 |
80 |
Full |
|
|
|
|
|
Half Load |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Program including steam action dedicated |
|
|
|
|
|
|
|
P6 |
Steam |
|
Delay |
|
for heavily soiled crockery, pots and pans. |
X |
14.0 |
1.70 |
180 |
Full |
|
|
|
|
Soaking or hand pretreatment is no longer |
|
||||||||
|
|
|
|
|
|
needed. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1)Program data obtained in conformity with European standard EN 50242, obtained under normal conditions (without additional options) and may vary depending on conditions. Differences of up to 20 minutes are possible with sensor programs as a result of the appliance’s automatic calibration system.
2)Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the EN/Standard loading comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.
GB -2-
How to set water hardness in order to always assure the best cleaning results |
First time use |
|
Water hardness should be set only |
|
|
- Press and hold together PROGRAM Selection and CANCEL/Off buttons for minimum 3 seconds. |
|
|
before the first wash or if water |
- The current water hardness setting will be visible on the display. |
|
hardness has been changed |
- Press the PROGRAM Selection button to increase setting. Value range goes from 1 to 7 (when the level reaches 7, the next |
|
|
press of the start button will set the level back to 1). |
|
|
- Wait 30 seconds (control panel switches off) or press Start/Resume button to save setting. |
|
|
|
|
Water hardness level is factory set for medium-hard water (level 4).
Even if you use tablets which include salt functionality, you must still add regeneration salt since such detergents are not effective enough at softening hard water.
At first time use, the salt reservoir has to be filled independently from water hardness level (see description below in step 1 “Daily check”).
1. Ask your water supply company what the water hardness is... |
2. ...enter this value |
Suggestions for detergent use |
|||||||
|
|
|
|
|
|
on your dishwasher |
|||
|
|
|
|
|
|
|
|
||
German |
French |
English |
Water hardness |
Insert value is shown |
Gel or Powder |
Tablets |
|||
degrees °dH |
degrees °fH |
degrees °eH |
level |
in the display |
(rinse aid and salt) |
||||
|
|||||||||
0 |
- 5 |
0 |
- 9 |
0 - 6.3 |
Soft |
1 |
|
|
|
|
|
|
|
|
|
|
|
||
6 - 10 |
10 |
- 18 |
7 - 12.6 |
Medium |
2 |
|
|
||
|
|
|
|
|
|
|
|
|
|
11 |
- 15 |
19 |
- 27 |
13.3 - 18.9 |
Average |
3 |
go to step 1 |
|
|
|
|
|
|
|
|
|
|
||
16 |
- 21 |
28 |
- 37 |
19.6 - 25.9 |
Medium-hard |
4 |
if water is |
||
(see “Daily |
|||||||||
|
|
|
|
|
|
|
check”) |
HARD extra salt |
|
22 |
- 28 |
38 |
- 50 |
26.6 - 35 |
Hard |
5 |
|||
needs to be |
|||||||||
|
|
|
|
|
|
|
|
||
29 |
- 35 |
51 |
- 63 |
35.7 - 44.1 |
Very hard |
6 |
|
added |
|
|
|
|
|
|
|
|
|
(go to step 1, |
|
36 |
- 50 |
64 |
- 90 |
44.8 - 62.4 |
Extremely hard |
7 |
|
||
|
“Daily check”) |
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
Filling the salt reservoir - Dissolve limescale (not necessary if water hardness level is set to “soft”!) |
|
Daily check |
|||
|
|
|
1 |
Visual indicator |
|
|
|
Screw on the cap. |
|
|
|
(depending |
|
|
|
Salt residual |
|
10 |
|
|
on the model). |
|
|
|
around the cap |
|
|
|
4 |
Unscrew cap. |
|
|
|
need to be |
|
|
|
|
|
|
|
|
|
removed. Some |
1 |
|
|
9 |
|
|
|
|
salt reservoir have |
|
|
|
|
|
|
a level indicator |
||
|
|
|
|
|
|
|
|
integrated in the |
|
|
|
|
|
|
|
|
cap (see below |
|
|
|
|
|
|
|
|
how to check). |
|
|
|
|
Fill the salt reservoir with water |
Add salt (never add detergent!) |
|
||
1- salt reservoir |
2 |
|
|
before the first wash only. |
min. 0.8 kg / max. 1 kg |
|
||
|
|
|
|
|
|
|||
3 |
|
|
Once regeneration salt is added, immediately start a wash program (the “Pre-wash” program alone is not sufficient). |
|
||||
2- rinse aid dispenser |
|
Residual saline solution or grains of salt can lead to deep-down corrosion, irreparably damaging the stainless steel components. |
|
|||||
3- detergent dispenser |
|
The guarantee is not applicable if faults are caused by such circumstances. |
|
|
|
|||
|
|
|
|
|
|
|||
4- racks system |
|
|
|
(depending on the model) |
|
|
|
|
5,6,7,8- available functions on the panel |
The salt level indicator lamp may remain lit |
Salt indicator on the control panel |
|
Salt indicator on the salt reservoir cap |
||||
9- filters |
6 |
7 |
8 |
at the end of several wash cycles. If the |
|
|
|
|
5 |
water hardness level falls within category |
The indicator lamp lights up when SALT |
green: OK. |
clear: NEEDS TO |
||||
10spray arms |
|
|
|
(soft), no salt is required. |
NEEDS TO BE ADDED. |
BE ADDED |
||
|
|
|
|
|
|
|
|
GB -3-
Adding rinse aid (not necessary when you use tablets). How to adjust the rinse aid dosage regulator |
Daily check |
2 |
Visual |
|
|
|
indicator |
If required, open the cover B (press the dedicated button).
(depending on the model)
Add rinse aid to the max. line ~150 ml
The rinse aid dosage can be adjusted to the detergent used. The lower the setting, the less rinse aid is dispensed (factory setting: position 4). Press the button to open the cover B. Using a coin or similar object, turn the arrow to the desired setting. After adjusting the rinse aid setting, shut the cover again.
Check the rinse aid indicator to check the |
Rinse aid indicator on the control panel |
Rinse aid indicator on the dispenser |
|
level into the dispenser. |
The indicator lamp lights up when |
dark: OK. |
clear: NEEDS TO BE ADDED |
|
RINSE AID NEEDS TO BE ADDED. |
||
|
|
|
|
|
|
|
|
Only use rinse aids recommended for use in domestic dishwashers. Immediately wipe away any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause a fault function of the appliance.
If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3). If crockery is not perfectly dry: increase the dosage by turning the dial to a higher setting (5-6). Plastic dishes have more difficulty drying and a higher rinse aid setting will not improve the situation.
Detergents with rinse aid incorporated may be effective only with longer programs. In the case of shorter programs, detergent residue may be a problem (if necessary, use powder detergent). Detergents with rinse aid incorporated tend to form excess suds.
Adding detergent - Use only detergent specifically for dishwashers in accordance with the supplier’s recommendations |
Daily use |
|
Open the cover A 3 (press the dedicated button).
Insert detergent: Tablet / powder / liquid into the big chamber. Please look for the recommendation of the detergent manufacturer on the packaging of the detergent product.
Only fill the detergent dispenser prior to starting a wash program.
Use only one tablet per one cycle, only placed in detergent dispenser.
All types of tablets can be used, but for 2 in 1 type adding of salt is mandatory.
Some types of tablets may not dissolve completely during the short cycles (Rapid, Fragile, Handwash); placing the tablet on the tub bottom can help dissolving and washing.
Shut the cover
by pressing dedicated ribs.
GB -4-