Whirlpool GSFK 1588 WS INSTRUCTION FOR USE

GSFK 1588

Before using the dishwasher, read the user instructions!

Quick Reference Guide

Options

Time and failure display

Programme selector knob

Indicates in hours the time remaining until
the start of the wash cycle. Switches off at
programme start and indicates the
remaining time in hours and minutes.

“F....” Information for the After-Sales

Service

GB

3)

On / Off button

“Delayed start” button

The wash cycle can be programmed to start
after 1 - 24 hours. With each successive touch
of the button, the delayed start indicator
increases by 1 hour, and after 24 returns to

00. Then press the Start button. The
dishwasher will start at the set time.

Start button

Switches “on” when the dishwasher is
operating. Flashes when a fault occurs.
Switches off at the end of the programme

.

Indicators

Add regeneration salt

Only add regeneration salt immediately
before starting a wash programme.

Add rinse aid

Programme chart

Programmes Loading instructions A B

Pre-Rinse cold

Rapid 30 min 40°C

Standard

Normal

Intensive

1) Reference programme for energy label in compliance with
EN 50242 regulations;

2) Refer to “User instructions“;

3) Program data obtained in conformity with European
standard EN 50242. Va lues may vary in relation to usage,
e.g.: different loads, water temperatur es - above or below
15°C - as well as water hardness and power supply
voltage, etc.

Important information for Test Laboratories:
For detailed information on the EN comparison test and other tests, contact the following address:
“[e-mail]”.

1) 5)

5)

5)

Crockery to be washed later.
Lightly soiled crockery, with

no dried-on food.
Normally soiled crockery.

50°C

Normally or heavily soiled

65°C

crockery.
Recommended programme

for heavily soiled crockery,

70°C

especially suitable for pots
and saucepans.

4) The bacteria removal efficiency has been tested by the
Institut Pasteur de Lille (France), based on the NF EN
13697 standard of November 2001.

5) These programmes can be used with the Antibacterial
rinse option.

Antibacterial Rinse

This function adds an antibacterial rinse at
the end of the wash cycle, thereby
guaranteeing a perfectly clean and sanitized
load. The lamp will light up when the
function is activated. If the temperature is
not maintained during the antibacterial cycle
(e.g. if the door is opened and remains open
for a long time), the lamp will start blinking
to indicate that sanitation is not guaranteed.

Detergent

- - 5.0 0.02 10

X - 13.0 0.70 30

X X 16.0 1.05 120

X X 16.0 1.65 100

X X 17.0 1.90 135

(We reserve the right to make technical modifications)

5019 496 98015

4)

2)

Consumption

Litres kWh Minutes

3)

How to use the appliance

Further indications are given in the single chapters and in the user instructions.

Switch on the appliance

How to fill the

detergent dispenser

Check the

rinse aid level

Check the regeneration

salt level

Load the racks

Close the door,

turn on the water tap

Select a programme

Press the ON/ OFF button.

Large compartment
With each wash cycle.
Small compartment
For programmes with pre-wash only.

Mechanical indicator C.
Electric indicator on control panel (if provided).

On models with water softener system only.

Mechanical indicator D.
Electric indicator on control panel (if provided).

Refer to the dishwasher loading instructions.

The last programme selected will light up.
Select the desired programme (using the specific button or
knob). The corresponding indicator lamp lights up.

A:

CBA

B:

Select additional

options

Press the START button

Wash cycle

Switch off the appliance

Shut off the water tap,

unload the racks

If necessary (and if provided) the corresponding indicator
lamp lights up.

The selected programme
is then memorised (even
in the event of power
failure).

Only after the START button has switched off: Press the

OFF

ON /

Warning: when the door is opened steam comes out!

Unload the appliance, starting from the lower rack.

button. All the indicator lamps switch off.

“Change programme”

Press the STAR T button for 2 sec. until
the Start indicator lamp switches of f;

Select another program m e and
press the START button again.

- Only open the dishwasher if necessary
(Warning: beware of hot steam).

- If the appliance is switched off during
a wash cycle, when switched on
again it will resume the cycle from
where it was interrupted.