Whirlpool GSF 7596 TW-WS PROGRAM CHART
GB
DYNAMIC SENSE: Energy savings and optimum wash results
The two sensor-controlled “DYNAMIC SENSE” wash options are
recommended for routine washes. They use double-sensor
technology. Separate sensors gauge turbid ity an d pa rticle s in o rder to
determine the degree of soiling of the wash w ater. In accordance with
values measured, a microprocessor establishes optimum water,
energy and time consumption. Optimum wash results are thus
achieved using only those resources strictly required.
GSF 7596
Further indications are given in the pages to follow and in the user instructions.
Water supply indicator
Check the appliance fills with water.
spray arm block indicator.
Lower
Release the spray arm.
“Water stop” device indicator
“Water stop” device not working.
Switch off the dishwasher and shut off
the water tap.
Rinse aid level indicator
Add rinse aid.
Salt level indicator
Add regeneration salt; only add
regeneration salt immediately before
starting a wash programme.
Programme Symbol
and Temperature
Eco Normal 40 - 55° C
Intensive 60 - 70° C
Pre-wash
Programme selection and
recommended load type
Recommended programme
for crockery with little or no dried-on food.
Recommended programme
crockery
for pans and saucepans.
Crockery to be washed later.
, with dried-on food. Especially suitable
Programme progress indicator
for routine washes
for heavily soiled
Quick Reference Guide
Pre-rinse /
Pre-wash
Washing
Options
Half Load button
This function can be used with any
programme. The indicator lamp
switches on: The wash cycle is
activated for the upper rack or lower
rack
only
.
,
Drying
Programme
End
small compartment large compartment
Place the detergent in the:
X X
X X
- - 5.0 (4.2) 0.02 (0.02) 9(9)
Delayed start button
The wash cycle can be programmed to start after 1-24 hours. Then
press the Start button. The dishwasher will start at the set time.
Time and failure display
Indicates in hours the time remaining until the start of the wash
cycle.
Switches off when the programme has started.
Toward the end of the programme, during the drying cycle, the
display will indicate the time remaining in minutes.
“F1--F9” Identification of faults for service technician.
Start button
Indicator lamp lit while the dishwasher is operating. Flashes when a
fault occurs. Switches off at the end of the programme.
On / Off Button
Consumption
Normal load / (Half load)
Water
(Litres)
(13.5)
(11.5)
(19.5)
(11.5)
Energy
(kWh)
(1.3)
(0.9)
(1.7)
(1.3)
1)
Time
(Min.)
(80)
(60)
(98)
(90)
Rapid 40° C
Glasses 40° C
Standard 50° C
1) Values may vary in relation to usage, e.g.: different loads, water temperatures - abo ve or below 15° C as well as water hardness and power supply voltage.
2) Reference programme for Test Institute and energy-label.
Lightly soiled crockery with no dried-on fo od.
Light soiling, especially glasses and cu ps.
Normally or heavily soiled crockery with dried-on
2)
food.
- X 13.0 (13.0) 0.85 (0.75) 30 (30)
- X 12.0 (10.0) 0.82 (0.78) 60 (59)
X X 16.0 (14.5) 1.03 (0.90) 120 (117)
5019 100 90335
(We reserve the right to make technical modifications)
A
A
C
B
C
D
How to use the dishwasher
1. After loading the dishwasher, close the
door properly and open the water
supply tap.
2. Press the On/Off button to switch the
dishwasher on.
indicator lamps will switch on.
3. Select the desired programme by
pressing the corresponding button.
The corresponding indicator lamp
lights up.
supplied).
4. Press theStart button to start the
selected programme.
indicator lamp will light up.
the programmed data cannot be
altered by pressing the programme
selector buttons.
once the Start button has been
Note:
pressed, the dishwasher memorises the
last programme selected. This
information remains in the memory even
during interruption of the power supply.
To change the selected
programme, press the Start button
for about 5 seconds
indicator lamp switches off.
Select a new programme and
press the Start button.
If the dishwasher is switched off
Note:
during a wash programme, when
switched on again it will resume the wash
cycle from where it was interrupted.
Only open the dishwasher door if
strictly necessary during a wash
cycle and exercise maximum
caution. Danger of scalding from
5. To indicate the end of the programme,
steam.
the Start indicator lamp switches off
and
the End indicator lamp (if fitted)
lights up
One of the programme
If required, select options (if
The Start
Once set,
, until the Start
(for about 30 min.)
.
6. Once the Start indicator lamp has
switched off press the On/Off bu tton to
switch the dishwasher off.
indicator lamps switch off.
7. Open the door (warning: beware of hot
steam). Unload the lower rack before
the upper one. Close the water tap.
All the
Upper rack
B
Half Load:
If the upper rack
the cutlery basket
Rack height adjustment:
(The dishwasher is delivered with the upper
rack in the top position).
The rack height can also be chan ged
when loaded.
• To lower: pull out the
handles and gently lower the rack.
• To raise: pull up the
until the rack clicks into place.
is to be loaded, place
only
in the upper rack.
“B”
side
two
side handles
two
Please read the user instructions carefully.
Upper and lower rack
• The rack must be level on both
sides.
Crockery holders:
• Down:
cups and long-stemmed glasses.
•
Up: plates.
“Vario Organizer” multi-purpose
support:
• To be used, for example, for longhandled utensils
with the blade facing downwards),
cups and glasses.
• May be used in three different
positions (see also “Dishwasher
loading instructions” on Page 4).
1. Upon the left-hand side of the rack.
2. Upside-down, towards the centre of
the rack.
3. Upside-down, towards the left side.
Glass holder:
(arrange knives
Lower rack
Half Load:
Loading the lower rack
greater washing power, especially for
plates and saucepans.
Plate holders:
• May be lowered to increase
available space (A).
only
gives
A
Cutlery basket:
• The cutlery basket (
removed to increase availabl e space.
• Some models are provided with a
grid (D) which can be fitted onto the
cutlery basket.
B + C
) can be
Loading...