GSF 2988
Before using the dishwasher, read the user instructions!
Quick Reference Guide
Wash cycle
On / Off button
GB
Programme selector
Start button
Switches “on” when the
dishwasher is operating. Flashes
when a fault occurs. Switches off
at the end of the programme.
Indicators
Add regeneration salt
only add regeneration salt
immediately before starting a
wash programme.
Add rinse aid
No water
Check that the appliance fills with
water.
Programmes Loading instructions A B Litres kWh Minutes
Pre-Rinse cold
Gentle 40°C
Rapid 30 min 40°C
Standard
Programme chart
Auto
Normal
Auto
Intensive
1)
40-55°C
60-70°C
Recommended programme for
routine washes, for crockery with
little dried-on food.
Recommended programme for
heavily soiled crockery, especially
suitable for pans and saucepans.
Crockery to be washed later. - - 4.0 0.03 14
Light soiling, for example
glasses and cups.
Lightly soiled crockery, with
no dried-on food.
Normally soiled crockery. X X 13.0 1.05 110
50°C
Pre-wash Washing Drying
Options
Time and failure display
Indicates in hours the time remaining
until the start of the wash cycle.
Switches off at programme start and
indicates the remaining time in hours
and minutes.
“F...” Information for the After-Sales
Service
“Delayed start” buttons
The wash cycle can be programmed to
start after 1 - 24 hours. Then press the
Start button. The dishwasher will start
at the set time.
“Half Load” button
This function can be used with any
programme. The indicator lamp
switches on. The wash cycle is activated
for the upper
Detergent
X X 10-13 0.8-1.05 50-110
X X 13-20 1.1-2.0 90-140
X - 10.0 0.80 55
X - 10.0 0.65 30
or
2)
lower rack
Consumption
Programme
3)
only
end
.
3)
1) Reference programme for energy label in
compliance with EN 50242 regulations;
2) Refer to “User instructions“;
3) Values may vary in relation to usage, e.g.:
different loads, water temperatures - above or
below 15° C - as well as water hardness and
power supply voltage, etc.
(We reserve the right to make technical modifications)
5019 496 90111
How to use the appliance
Further indications are given in the single chapters and in the user instructions.
Switch on the appliance
How to fill the
detergent dispenser
Check the
rinse aid level
Check the regeneration
salt level
Load the racks
Close the door,
turn on the water tap
Select a programme
Press the ON/ OFF button.
Large compartment
With each wash cycle.
Small compartment
For programmes with pre-wash only.
Mechanical indicator lamp C.
Electric indicator on control panel (if provided).
On models with water softener system only.
Mechanical indicator lamp D.
Electric indicator on control panel (if provided).
Refer to the dishwasher loading instructions.
The last programme selected will light up.
Select the desired programme (using the specific button or
knob). The corresponding indicator lamp lights up.
A:
B:
Select additional
options
Press the START button
Wash cycle
Switch off the appliance
shut off the water tap,
unload the racks
If necessary (and if provided) the corresponding indicator
lamp lights up.
The selected programme
is then memorised (even
in the event of power
failure).
Only after the START button has switched off: press the
OFF
ON /
Warning: when the door is opened steam comes out!
Unload the appliance, starting from the lower rack.
button. All the indicator lamps switch off.
“Change programme”
Press the START button for 2 sec. until
the Start indicator lamp switches off;
Select another programme and
press the START button again.
- Only open the dishwasher if necessary
(Warning: beware of hot steam).
- If the appliance is switched off during
a wash cycle, when switched on
again it will resume the cycle from
where it was interrupted.