Whirlpool GSF 2684 WS INSTRUCTION FOR USE
GSF 2684
Before using the dishwasher, read the user instructions!
Quick Reference Guide
Wash cycle
GB
Programme selector knob
Pre-Rinse Washing Drying
Options
On / Off button
Start button
Switches “on” when the
dishwasher is operating. Flashes
when a fault occurs. Switches off
at the end of the programme.
Indicators
Add rinse aid
Add regeneration salt
Only add regeneration salt
immediately before starting a
wash programme.
Programme chart
Programmes Loading instructions A B
Pre-Rinse cold
Rapid 30 min 40°C
Crockery to be washed later. - - 5.0 0.02 10
Lightly soiled crockery with no dried-on food. X - 13.0 0.70 30
Programme
end
Time and failure display
Indicates in hours the time remaining
until the start of the wash cycle.
Switches off when the programme
starts and indicates the time remaining
in hours and minutes.
“F...” Information for the AfterSales Service
“Delayed start” button
The wash cycle can be programmed to
start after 1 - 24 hours. With each
successive touch of the button, the
delayed start indicator increases by 1
hour, and after 24 returns to 00. Then
press the Start button. The dishwasher
will start at the set time.
Detergent
2)
Litres kWh Minutes
3)
Consumption
3)
Bio/Eco 50°C
1)
Eco
Normal
Intensive
1) Reference programme for energy label in
compliance with EN 50242 regulations;
2) Refer to “User instructions“;
Important information for Test Laboratories:
For detailed information on the EN/Standard loading comparison test, contact the following ad dress:
“nk_customer@email.whirlpool.com”.
1)
Normally soiled crockery. X - 13.0 1.35 80
Normally soiled crockery. X X 16.0 1.05 120
50°C
Normally or heavily soiled crockery. X X 16.0 1.65 90
65°C
Heavily soiled crockery, especially pots and
70°C
pans.
3) Program data obtained in conformity with
European standard EN 50242. Values may vary in
relation to usage, e.g.: different loads, water
temperatures - above or below 15°C - as well as
water hardness and power supply voltage, etc.
(We reserve the right to make technical modifications)
X X 17.0 1.90 125
5019 496 90237
How to use the appliance
C
BA
Further indications are given in the single chapters and in the user instructions.
Switch on the appliance
How to fill the
detergent dispenser
Check the
rinse aid level
Check the regeneration
salt level
Load the racks
Close the door,
turn on the water tap
Select a programme
Press the ON/ OFF button.
Large compartment
With each wash cycle.
Small compartment
For programmes with pre-wash only.
Mechanical indicator lamp C.
Electric indicator on control panel (if provided).
On models with water softener system only.
Mechanical indicator lamp D.
Electric indicator on control panel (if provided).
Refer to the dishwasher loading instructions.
The last programme selected will light up.
Select the desired programme (using the specific button or
knob). The corresponding indicator lamp lights up.
A:
B:
Select additional
options
Press the START button
Wash cycle
Switch off the appliance
Shut off the water tap,
unload the racks
If necessary (and if provided) the corresponding indicator
lamp lights up.
The selected programme
is then memorised (even
in the event of power
failure).
Only after the START button has switched off: Press the
OFF
ON /
Warning: when the door is opened steam comes out!
Unload the appliance, starting from the lower rack.
button. All the indicator lamps switch off.
“Change programme”
Press the START button for 2 sec. until
the Start indicator lamp switches off;
Select another programme and
press the START button again.
- Only open the dishwasher if necessary
(Warning: beware of hot steam).
- If the appliance is switched off during
a wash cycle, when switched on
again it will resume the cycle from
where it was interrupted.
Loading...