Whirlpool ED25CQXHB01, ED25CQXFN02, ED25CQXFB00, ED20TQXFW03, ED20TQXFT03 Owner’s Manual
...
)liances
SIDE BYSIDE
REFRIGERATOR
For questions about features, operation/performance
parts accessories or service, call: 1-800-253-1301.
In Canada, call for assistance 1-800-461-5681, for installation
www.whirlpooLcom or www.whirlpool.com/canada
and service, call: 1-800-807-8777
or visit our website at...
RI_FRIGI_RATEUR
COTE ACOTE
Au Canada, pour assistance, composer le 1-800-461-5681, pour
Table of Contents/Table des matieres ......................................... 2
installation ou service 1-800-807-8777
ou visitez notre site web _]
www.whirlpool,com/canada
2205958
TABLEOFCONTENTS
TABLEDESMATIERES
REFRIGERATOR SAFETY ..........................................................3
ProperDisposalofYour Old Refrigerator....................................3
INSTALLING YOUR REFRIGERATOR .......................................4
Unpacking Your Refrigerator.......................................................4
Space Requirements....................................................................4
Electrical Requirements ............................................................... 5
Removing the Doors .................................................................... 5
Removing the Door Handles ........................................................ 6
Connecting the Refrigerator to aWater Source .......................... 7
Interior Water Filter Installation .................................................... 8
Water System Preparation ........................................................... 8
Base Grille .................................................................................... 8
Door Closing ................................................................................. 8
Understanding Sounds You May Hear........................................ 9
USING YOUR REFRIGERATOR .................................................9
Ensuring Proper Air Circulation .................................................... 9
Setting the Controls ................................................................... 10
Adjusting Control Settings ......................................................... 10
REFRIGERATOR FEATURES ................................................... 11
Water and Ice Dispensers .......................................................... 11
Base Grille Water Filtration and Monitoring System ................. 12
Interior Water Filtration System ................................................. 13
Refrigerator Shelves ................................................................... 13
Lateral Adjustable Shelf ............................................................. 14
Flip-up Shelf ............................................................................... 14
Adjustable Flip-up Shelf ............................................................. 14
Dell Drawer ................................................................................. 14
Convertible Vegetable/Meat Drawer, Crisper and Covers ........ 15
Convertible Vegetable/Meat Drawer Temperature Control ....... 15
Crisper Humidity Control ........................................................... 15
Utility or Egg Bin......................................................................... 16
Wine or Can/Bottle Rack ........................................................... 16
FREEZER FEATURES .............................................................. 16
Ice Maker and Storage Bin/Bucket ............................................ 16
Freezer Shelf .............................................................................. 17
Freezer Basket ........................................................................... 17
DOOR FEATURES .................................................................... 18
Door Rails ................................................................................... 18
Door Bins .................................................................................... 18
Can Rack .................................................................................... 18
CARING FOR YOUR REFRIGERATOR ...................................18
Cleaning Your Refrigerator ......................................................... 18
Changing the Light Bulbs ........................................................... 19
Power Interruptions .................................................................... 20
Vacation and Moving Care ......................................................... 20
TROUBLESHOOTING ............................................................... 20
ASSISTANCE OR SERVICE ..................................................... 24
Accessories ................................................................................ 24
WARRANTY .............................................................................. 25
WATER FILTER CERTIFICATIONS ......................................... 26
PRODUCT DATA SHEETS ....................................................... 28
SECURITE DU REFRIGERATEUR ........................................... 30
Mise au rebut de votre vieux refrigerateur ................................. 30
INSTALLATION DU RE_FRIGERATEUR ................................... 31
Deballage de votre [efrigerateu[ ................................................ 31
Espacement requis..................................................................... 31
Specifications (_lectriques .......................................................... 32
Enlevement des portes ............................................................... 32
Enlevement des poignees des portes ........................................ 33
Raccordement du rdrigerateur a une canalisation d'eau .........34
Systeme interieur de filtration d'eau .......................................... 35
Preparation du systeme d'eau ................................................... 35
Grille de la base .......................................................................... 36
Fermeture des portes ................................................................. 36
Les bruits de I'appareil que vous pouvez entendre ................... 36
UTILISATION DU RE_FRIGleRATEUR ....................................... 37
Pour s'assurer d'une circulation d'air appropri(_e ...................... 37
Reglage des commandes .......................................................... 37
Ajustement des reglages de controle ........................................ 38
CARACTERISTIQUES DU RleFRIGleRATEUR ......................... 38
Distributeurs d'eau et de glaqons .............................................. 38
Systeme de filtration et de controle d'eau a la
grille de la base ........................................................................... 40
Systeme de filtration d'eau interieur .......................................... 41
Tablettes du refrigerateur ........................................................... 41
Tablette reglable laterale ............................................................ 42
Tablette relevable ....................................................................... 42
Tablette relevable ajustable ....................................................... 42
Tiroir pour specialites alimentaires ............................................ 42
Tiroir a legumes/viande convertible, bac a
legumes et couvercles ............................................................... 43
Reglage de la temperature du tiroir
legumes/viande convertible ....................................................... 43
Reglage de I'humidite dans le bac a legumes ........................... 44
Casier utilitaire ou oeufrier .......................................................... 44
Casier a vin ou porte-cannettes/bouteilles ................................ 44
CARACTE_RISTIQUES DU CONGE_LATEUR ............................ 44
Machine a glacons et bac/seau d'entreposage ........................ 44
Tablette de congelateur ............................................................. 46
Partier de congelateur ................................................................ 46
CARACTE_RISTIQUES DE LA PORTE ...................................... 46
Tringles dans la porte ................................................................. 46
BaIconnets .................................................................................. 46
Porte-cannettes .......................................................................... 47
ENTRETIEN DE VOTRE RE_FRIGERATEUR ............................ 47
Nettoyage du [efrigerateu[ ......................................................... 47
Remplacement des ampoules d'eclairage ................................ 47
Pannes de courant ..................................................................... 48
Entretien avant les vacances ou lots d'un demenagement .......49
DI_PANNAGE .............................................................................49
ASSISTANCE OU SERVICE ......................................................53
Accessoires................................................................................53
GARANTIE .................................................................................54
FEUlLLES DE DONNEES SUR LE PRODUIT ..........................55
REFRIGERATORSAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all
safety messages.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or
This is the safety alert symbol.
"WARNING." These words mean:
You can be killed or seriously injured if you don't
immediately follow instructions.
You can be killed or seriously injured if you don't
follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you
what can happen if the instructions are not followed.
IMPORTANTSAFETYINSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic
precautions:
• Plug into a grounded 3 prong outlet.
• Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Disconnect power before servicing.
Replace all panels before operating.
Remove doors from your old refrigerator.
• Use nonflammable cleaner.
• Keep flammable materials and vapors, such as
gasoline, away from refrigerator.
• Use two or more people to move and install
refrigerator.
• Disconnect power before installing ice maker (on
ice maker kit ready models only).
• Use a sturdy glass when dispensing ice or water
(on some models).
SAVETHESEINSTRUCTIONS
:_" t_ _:,_,__4:_ ' ........
Suffocation Hazard
Remove doors from your old refrigerator.
Failure to do so can result in death or
brain damage.
IMPORTANT: Child entrapment and suffocation are not problems
of the past. Junked or abandoned refrigerators are still dangerous
- even if they will sit for ':just a few days." Ifyou are getting rid of
your old refrigerator, please follow these instructions to help
prevent accidents.
Before you throw away your old refrigerator or freezer:
• Take off the doors.
• Leave the shelves in place so that children may not easily
climb inside.
-_JJ
INSTALLINGYOUR
REFRIGERATOR
Excessive Weight Hazard
Use two or more people to move and install
refrigerator.
Failure to do so can result in back or other injury.
Removing packaging materials
• Remove tape and any labels from your refrigerator before
using (except the model and serial number label).
To remove any remaining tape or glue, rub the area briskly
with your thumb. Tape or glue residue can also be easily
removed by rubbing a small amount of liquid dish soap over
the adhesive with your fingers. Wipe with warm water and
dry.
• Do not use sharp instruments, rubbing alcohol, flammable
fluids, or abrasive cleaners to remove tape or glue. These
products can damage the surface of your refrigerator. For
more information, see the "Refrigerator Safety" section.
IMPORTANT: Do not remove any permanent instruction labels
inside your refrigerator, or the Tech Sheet that is fastened to the
base grille.
When Moving Your Refrigerator:
Your refrigerator is heavy. When moving the refrigerator
for cleaning or service, be sure to protect the floor,
Aiways pulI the refrigerator straight out when moving it.
Do not wiggle or "walk" the refrigerator when trying to move
it, as floor damage could occur.
Cleaning before use
After you remove all of the packaging materials, clean the inside
of your refrigerator before using it. See the cleaning instructions
in the "Caring for Your Refrigerator" section.
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from refrigerator.
Failure to do so can result in death, explosion,
or fire.
To ensure proper ventilation for your refrigerator, allow for
.5 in. (1.25 cm) space on each side and at the top.
_Jl,
/
ji
.5" (1.25 cm)
- II -- I!
F ..... 2
2"(5.08cm}
• If your refrigerator has an ice maker, make sure you leave
some extra space at the back for the water line connections.
The refrigerator can be flush against the back wall if you do
not have an ice maker installed.
• If you are installing your refrigerator next to a fixed wall, leave
2 in. (5.08 cm) minimum on each side (depending on your
model) to allow for the door to swing open.
NOTE: Do not install the refrigerator near an oven, radiator, or
other heat source, nor in a location where the temperature will fall
below 55°F (13°C).
4
___o ¸_@_ __,_,_w,_
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in
death, fire, or electrical shock.
Before you move your refrigerator into its final location, it is
important to make sure you have the proper electrical
connection:
Recommended grounding method
A 115 Volt, 60 Hz., AC only 15 or 20 ampere fused, grounded
electrical supply is required. It is recommended that a separate
circuit serving only your refrigerator be provided. Use an outlet
that cannot be turned off by a switch. Do not use an
extension cord.
NOTE: Before performing any type of installation, cleaning, or
removing a light bulb, turn the control, (Thermostat, Refrigerator
or Freezer Control depending on the model) to OFF and then
disconnect the refrigerator from the electrical source. When you
are finished, reconnect the refrigerator to the electrical source
and reset the control (Thermostat, Refrigerator or Freezer Control
depending on the model) to the desired setting.
Electrical Shock Hazard
Disconnect power before removing doors.
Failure to do so can result in death or
electrical shock.
NOTE: Before removing doors, open both doors and remove
base grille (see the "Base Grille" section).
Tools Needed:
1/4in. hex-head socket wrench and _A6in. hex-head socket
wrench.
1. Unplug refrigerator or disconnect power.
2. If you have a dispenser (ice or water), disconnect water line
(behind base grille).
• Remove hose from clip.
• Disconnect union nut and slide it back onto tube.
• Remove metal insert from tube.
• Remove union nut and spring.
Remove left top hinge.
• Remove hinge cover and screws. DO NOT REMOVE
SCREW 1 AS SHOWN IN DIAGRAM.
• Disconnect wiring plug and both ground wires.
Carefully lift door up off bottom hinge. Make sure you
protect water line from damage.
Style 1
Style2 6. Replacedoors.
I
I
4. Disassemblerighttophinge,
• Removehingecoverandscrews,DONOTREMOVE
SCREW1ASSHOWNINDIAGRAM.
Reconnect both ground wires.
Failure to do so can result in death or
electrical shock.
• Lift door up off bottom hinge.
Style 1
7. Reconnect both ground wires.
8. Reconnect wiring plug.
9. Replace hinge cover and screws.
10. Plug in refrigerator or reconnect power.
Electrical Shock Hazard
Style 2
Remove bottom hinge, if necessary. Both bottom hinges have
similar construction. DO NOT REMOVE SCREW 1 AS
SHOWN IN DIAGRAM.
NOTE: It may not be necessary to remove the bottom hinge
to move refrigerator through a doorway.
Apply firm pressure with hand on face of trim. Slide top trim up
and bottom trim down away from handle, then lift off of shoulder
screws. Remove handle screws.
J
f
Read all directions carefully before you begin.
IMPORTANT:
• if operating the refrigerator before installing the water
connection, turn ice maker to the OFF position to prevent
operation without water.
• All installations must be in accordance with local plumbing
code requirements,
• Use copper tubing and check for leaks,
• Install copper tubing only in areas where temperatures will
remain above freezing,
• It may take up to 24 hours for your ice maker to begin
producing ice.
Tools required:
• Standard screwdriver
• 7A6in. and _/2in. open-end wrenches or two adjustable
wrenches
• ¼in. nut driver
• ¼in. drill bit
• Hand drill or electric drill (properly grounded)
NOTE: Your refrigerator dealer has a kit available with a
¼ in. (6.35 mm) saddle-type shut-off valve, a union, and copper
tubing. Before purchasing, make sure a saddle-type valve
complies with your local plumbing codes. Do not use a piercing-
type or 3A6in. (4.76 ram) saddle valve which reduces water flow
and clogs more easily.
Cold water supply
The ice maker water valve contains a flow washer which is used
as a water pressure regulator. The ice maker needs to be
connected to a cold water line with water pressure between 30
and 120 psi. If a problem occurs, call your utility company.
Connecting to water line:
1. Unplug refrigerator or disconnect power.
2. Turn OFF main water supply. Turn ON nearest faucet long
enough to clear line of water.
3. Locate a V2in. to 1¼ in. (12.7 mm to 3.18 cm) vertical COLD
water pipe near the refrigerator.
NOTE: Horizontal pipe will work, but the following procedure
must be followed: Drill on the top side of the pipe, not the
bottom. This will help keep water away from the drill. This
also keeps normal sediment from collecting in the valve.
4. To determine the length of copper tubing you will need,
measure from connection on lower left rear of refrigerator to
water pipe. Add 7 ft. (2.1 m) to allow for moving refrigerator
for cleaning. Use ¼ in. (6.35 ram) O.D. (outside diameter)
copper tubing. Be sure both ends of copper tubing are cut
square.
5. Using a grounded drill, drill a ¼ in. hole in the cold water pipe
you have selected.
....................1
7 .......................2
..... ..............3
1.Cold WaterPipe
2. Pipe Clamp
3. Copper Tubing
4. Compression Nut
5. Compression Sleeve
6. Shut-Oft Valve
7.Packing Nut
6. Fasten shut-off valve to cold water pipe with pipe clamp. Be
sure outlet end is solidly in the ¼ in. drilled hole in the water
pipe and that washer is under the pipe clamp. Tighten
packing nut. Tighten the pipe clamp screws carefully and
evenly so washer makes a watertight seal. Do not overtighten
or you may crush the copper tubing, especially if soft (coiled)
copper tubing is used. Now you are ready to connect the
copper tubing.
7. Slip compression sleeve and compression nut on copper
tubing as shown. Insert end of tubing into outlet end squarely
as far as it will go. Screw compression nut onto outlet end
with adjustable wrench. Do not overtighten.
8. Place the free end of the tubing into a container or sink, and
turn ON main water supply and flush out tubing until water is
clear. Turn OFF shut-off valve on the water pipe. Coil copper
tubing.
Connecting to refrigerator:
1. Attach the copper tube to the valve inlet using a compression
nut and sleeve as shown. Tighten the compression nut. Do
not overtighten. Use the tube clamp on the back of the
refrigerator to secure the tubing to the refrigerator as shown.
This will help prevent damage to the tubing when the
refrigerator is pushed back against the wall. Move to step 2.
2. Turn shut-off valve ON. Check for leaks. Tighten any
connections (including connections at the valve) or nuts that
leak.
"_ 1
2
1. Tube Clamp
2. Copper Tubing
3. Compression Nut
4. Valve Inlet
3. The ice maker is equipped with a built-in water strainer. If
local water conditions require periodic cleaning or a well is
your source of water supply, a second water strainer should
be installed in the ¼ in. (6.35 mm) water line. Obtain a water
strainer from your nearest appliance dealer. Install at either
tube connection.
4. Plug in refrigerator or reconnect power.
The interior water filter cartridge is located in the upper right-
hand corner of the fresh food compartment of the refrigerator.
The interior water filter cartridge should be replaced every six
months or earlier if the flow of water to your water dispenser or
ice maker decreases noticeably. (See "Replacing an interior water
filter cartridge" in the features section of this book.)
Installing the interior water filter cartridge
NOTE: Do not use with water that is microbiologically unsafe
or of unknown quality without adequate disinfection before
or after the system.
1. Carefully remove the interior water filter cartridge from its
packaging. Remove the red cap from the cartridge.
2. Apply the appropriate month sticker to the cartridge as a
reminder to replace the cartridge within six months. Then
apply the "Water Filter Replacement Reminder" sticker to
your calendar as a reminder to replace the cartridge in six
months.
Style 2
Flush the water system by dispensing and discarding
2 to 3 gallons (approximately 6 to 7 minutes) of water through
the dispenser. This will clean the system and help clear air
from the lines. Additional flushing may be required in some
households.
Open the freezer door and turn on the ice maker. For Style 1
lower the wire shut-off arm. For Style 2 move the switch to
the ON (left) position. Please refer to the "Ice Maker and
Storage Bin/Bucket" features section for further instructions
on the operation of your ice maker.
• Allow 24 hours to produce the first batch of ice.
• Discard the first three batches of ice produced.
• Depending on your model, you may want to select the
maximum ice feature to increase the production of ice. To
do so, set the switch on the front of the ice maker to MAX.
3. Line up the INSTALL mark on the water filter label with the
indicator line that is molded into the filter mounting bracket
cover. Push the cartridge into the filter mounting bracket.
Twist the cartridge _/4turn to the right to lock it into place. The
REMOVE mark should be lined-up with the indicator line
located on the front cover.
4. RUN WATER THROUGH THE DISPENSER UNTIL THE
WATER RUNS CLEAR (about 2-3 gallons or 6-7 minutes).
This will clean the system and clear air from the lines.
Additional flushing may be required in some households.
NOTE: As air is cleared from the system, water may spurt out
of the dispenser.
5. Open the refrigerator door and inspect the filter system for
water leaks. If you see water leaks, see the "Troubleshooting"
section.
NOTE: You can run the dispenser without a water filter cartridge.
Your water will not be filtered.
Please read before using the water system.
Immediately after installation, follow the steps below to make
sure that the water system is properly cleaned.
1. Open the freezer door and turn off the ice maker. For Style 1
lift up the wire shut-off arm as shown. For Style 2 move the
switch to the OFF (right) setting as shown.
Style 1
U
To remove the base grille:
1. Open both refrigerator doors.
2. Place hands along the ends of the grille, with your thumbs
along the top. Push in with your thumbs and pull up on the
bottom.
NOTE: Be sure to refasten the Tech Sheet behind the base grille
after cleaning.
To replace the base grille:
1. Open the doors.
2. Line up the grille support tabs with the metal clips.
3. Push the grille firmly to snap it into place.
Your refrigerator has two front adjustable rollers -- one on the
right and one on the left. If your refrigerator seems unsteady or if
you want the doors to close more easily, adjust the refrigerator's
tilt using the instructions below:
1. Plug into a grounded 3 prong outlet.
2. Move the refrigerator into its final position.
3. Remove the base grille (see "Base Grille" earlier in this
section). The two leveling screws are part of the front roller
assemblies which are at the base of the refrigerator on either
side.
4,
Use a screwdriver to adjust the leveling screws. Turn the
leveling screw to the right to raise that side of the refrigerator
or turn the leveling screw to the left to lower that side. It may
take several turns of the leveling screws to adjust the tilt of
the refrigerator.
NOTE: Having someone push against the top of the
refrigerator takes some weight off the leveling screws and
rollers. This makes it easier to adjust the screws.
5. Open both doors again and check to make sure that they
close as easily as you like. If not, tilt the refrigerator slightly
more to the rear by turning both leveling screws to the right. It
may take several more turns, and you should turn both
leveling screws the same amount.
6. Replace the base grille.
USINGYOUR
REFRIGERATOR
In order to ensure proper temperatures, you need to permit air to
flow between the two sections. Cold air enters the bottom of the
freezer section and moves up. It then enters the refrigerator
section through the top vent. Air then returns to the freezer as
shown.
< +
Your new refrigerator may make sounds that your old one didn't
make. Because the sounds are new to you, you might be
concerned about them. Most of the new sounds are normal. Hard
surfaces, like the floor, walls, and cabinets, can make the sounds
seem louder than they actually are. The following describes the
kinds of sounds and what may be making them.
• If your product is equipped with an ice maker, you will hear a
buzzing sound when the water valve opens to fill the ice
maker for each cycle.
• The defrost timer will click when the automatic defrost cycle
begins and ends. Also, the Thermostat Control (or
Refrigerator Control depending on the model) will click when
cycling on and off.
• Rattling noises may come from the flow of refrigerant, the
water line, or items stored on top of the refrigerator.
• Your refrigerator is designed to run more efficiently to keep
your food items at the desired temperature. The high
efficiency compressor may cause your new refrigerator to run
longer than your old one, and you may hear a pulsating or
high-pitched sound.
• Water dripping on the defrost heater during a defrost cycle
may cause a sizzling sound.
• You may hear the evaporator fan motor circulating the air
through the refrigerator and freezer compartments.
• As each cycle ends, you may hear a gurgling sound due to
the refrigerant flowing in your refrigerator.
• Contraction and expansion of the inside walls may cause a
popping noise.
• You may hear air being forced over the condenser by the
condenser fan.
• You may hear water running into the drain pan during the
defrost cycle.
Do not block any of these vents with food such as soda, cereal,
bread, etc. If the vents are blocked, airflow will be prevented and
the temperature controls will not function properly.
IMPORTANT: Because air circulates between both sections, any
odors formed in one section will transfer to the other. You must
thoroughly clean both sections to eliminate odors. To prevent
odor transfer from food, wrap or cover foods tightly.
For your convenience, your refrigerator controls are preset at
the factory. When you first install your refrigerator, make sure
that the controls are still preset. The Refrigerator Control and the
Freezer Control should both be at the "mid-settings" as shown in
the illustrations below.
Style 1
REFRRGERATOR
I
, 3 4
1 6 COLDER
COLD
FREEZER
COLDER COLD
NOTE: Your product will not cool when the REFRIGERATOR
Control is set to OFE
Style 2
FR E_EZER REFRIGERATOR
3 7
COLD 2 8 COLDER COLD
1 9
COLDER
Give the refrigerator time to cool down completely before adding
food. It is best to wait 24 hours before you put food into the
refrigerator. The settings indicated in the previous section should
be correct for normal household refrigerator usage. The controls
are set correctly when milk orjuice is as cold as you like and
when ice cream is firm.
If you need to adjust temperatures in the refrigerator or freezer,
use the settings listed in the chart below as a guide. Wait at least
24 hours between adjustments.
RECOMMENDED
CONDITION/REASON: ADJ USTMENT:
REFRIGERATOR section Adjust
too warm REFRIGERATOR
• Door opened often Control one setting
• Large amount of food added
higher
For Style 1 controls
• Room temperature very warm only: after adjusting
control, wait 24
hours and then
check the FREEZER
temperature
• Air vent blocked byitems
Move packages out
of airstream
NOTE: Your product will not cool when the FREEZER Control is
set to OFE
The Refrigerator Control adjusts the refrigerator
compartment temperature. Settings to the left of the mid-
setting make the temperature less cold. Settings to the right of
the mid-setting make the temperature colder.
The Freezer Control adjusts the freezer compartment
temperature. Settings to the left of the mid-setting make the
temperature less cold. Settings to the right of the mid-setting
make the temperature colder.
Give your refrigerator time to cool down completely before
adding food. It is best to wait 24 hours before you put food into
the refrigerator.
IMPORTANT: If you add food before the refrigerator has cooled
completely, your food may spoil. Adjusting the Refrigerator and
Freezer Controls to a higher (colder) than recommended
setting will not cool the compartments any faster.
FREEZER section too warm/ice
not made fast enough
• Door opened often
Adjust FREEZER
Control one setting
higher
• Large amount of food added
• Very cold room temperature
(can't cycle often enough)
• Heavy ice usage
REFRIGERATOR section
too cold
• Controls not set correctly for your
conditions
Adjust
REFRIGERATOR
Controlone setting
lower
For Style 1 controls
only: after adjusting
control, wait 24
hours and then
check the FREEZER
temperature
FREEZER section too cold Adjust FREEZER
• Controls not set correctly for your Control one setting
conditions lower
10
REFRIGERATOR
FEATURES
Your model may have some or all of these features. Features that
can be purchased separately as product accessories are labeled
with the word "Accessory." Not all accessories will fit all models.
If you are interested in purchasing one of the accessories, please
call the toll-free number on the cover or in the "Assistance or
Service" section.
Cut Hazard
Use a sturdy glass when dispensing ice or water.
Failure to do so can result in cuts.
Depending on your model, you may have one or more of the
following options: the ability to select either crushed or cubed
ice, a special light that turns on when you use the dispenser, or a
lock option to avoid accidental dispensing.
To dispense ice:
1. Press button for the desired type of ice.
2. Press a sturdy glass against the ice dispenser lever. Hold the
glass close to the dispenser opening so ice does not fall
outside of the glass.
IMPORTANT: You do not need to apply a lot of pressure to
the lever in order to activate the ice dispenser. Pressing hard
will not make the ice dispense faster or in greater quantities.
3. Remove the glass to stop dispensing.
NOTE: The first few batches of ice may have an off-flavor
from new plumbing and parts. Throw the ice away. Also, take
large amounts of ice from the ice bin, not through the
dispenser.
The water dispenser
When the refrigerator is first hooked up, press the water
dispenser bar with a glass orjar until you draw and discard 2 to 3
quarts (1.9 to 2.8 L). It will take three to four minutes for the water
to begin dispensing. The water you draw and discard rinses the
pipes. Allow several hours for the refrigerator to cool down and
chill water.
IMPORTANT: Depending on your model, the small removable
tray at the bottom of the dispenser is designed to catch small
spills and allow for easy cleaning, There is no drain in the tray,
The tray can be removed from the dispenser and carried to the
sink to be emptied or cleaned,
The ice dispenser
Ice dispenses from the ice maker storage bin inthe freezer. When
the dispenser lever is pressed:
• A trap door opens in a chute between the dispenser and the
ice bin.
• Ice moves from the bin and falls through the chute.
• When you release the dispenser lever, the trap door closes
and the ice dispensing stops. The dispensing system will not
operate when the freezer door is open.
Some models dispense both cubed and crushed ice. Before
dispensing ice, select which type of ice you prefer. The button
controls are designed for easy use and cleaning.
• For cubed ice, press the CUBE button until the red indicator
appears in the window above the CUBE button.
m
ICE
CRUSH CUBE
• For crushed ice, press the CRUSH button until the red
indicator appears in the window above the CRUSH button.
For crushed ice, cubes are crushed before being dispensed. This
may cause a slight delay when dispensing crushed ice. Noise
from the ice crusher is normal, and pieces of ice may vary in size.
When changing from CRUSH to CUBE, a few ounces of crushed
ice will be dispensed along with the first cubes.
To dispense water:
1. Press a glass against the water dispenser lever.
2. Remove the glass to stop dispensing.
NOTE: Dispense enough water every week to maintain a fresh
supply
11
The dispenser light
The dispenser area has a light. It can be turned on manually by
pressing the ON button at the right hand side of the control panel,
The red indicator above the ON button will appear, On some
models: Whenever you use the dispenser the lever will
automatically turn the light on.
LIGHT
OFF ON
NOTE: See the "Changing the Light Bulbs" section for
information on changing the dispenser light bulb.
On models without crushed ice, the light switch is a rocker-style
type. Push the switch to turn the light on, and push again to turn
the light off.
The dispenser lock (on some models)
Your dispenser can be turned off for easy cleaning or to prevent
accidental dispensing by small children and pets, Toturn off the
dispenser, press the LOCK button, The indicator will appear
above the LOCK button and the ice and water dispensers will not
work, To unlock the dispenser, press the UNLOCK button until
the indicator appears. Then continue to dispense ice or water as
usual,
u
DISPENSER
Non-indicator water filter (on some models)
If your refrigerator does not have the water filter status light, you
should change the water filter cartridge every 6-9 months
depending upon your usage. If the water flow to the water
dispenser or icemaker decreases noticeably before 6 months
have passed, replace the water filter cartridge more often. (See
"Changing a base water filter cartridge" later in this section.)
Changing a base grille water filter cartridge
The base grille water filter is located below the freezer
compartment door.
1. Locate the water filter cartridge cap in the front base grille
below the freezer compartment door. Rotate the cap
counterclockwise to a vertical position and pull the cap and
filter cartridge out through the base grille.
NOTE: There will be water in the cartridge. Some spilling may
occur.
2. Remove the cartridge cap by sliding it off the end of the old
cartridge. The cap will slide to the left or right. DO NOT
DISCARD THE CAR
LOCK UNLOCK
NOTE: The lock feature does not shut off power to the product,
to the ice maker, or to the dispenser light. It simply deactivates
the dispenser levers.
The base grille water filter status light
The water filter status light will help you know when to change
your water filter cartridge. The light is located at the top of the
refrigerator compartment. The light will change from green to
yellow. This tells you that it is almost time to change the water
filter cartridge (90% of the filter life has been used). It is
recommended that you replace the base grille water filter
cartridge when the water filter indicator light changes to red OR
water flow to your water dispenser or ice maker decreases
noticeably. (See "Changing a base grille water filter cartridge"
later in this section.)
NOTE: Do not use with water that is microbiologically unsafe
or of unknown quality without adequate disinfection before
or after the system.
3. Take the new cartridge out of its packaging and remove
protective cover from o-rings.
4. Slide the cartridge cap onto the new cartridge as shown
above in Step 2.
5. With cartridge cap in the vertical position, push the new filter
cartridge into the base grille until it stops. Rotate the cartridge
cap clockwise to a horizontal position.
1. Status Light
2. Light Switch
After changing the water filter cartridge, reset the water filter
status light by pressing the light switch 5 times within 10
seconds. The status light will change from red to green when the
system is reset.
12
61 RUN WATER THROUGH THE DISPENSER UNTIL THE
WATER RUNS CLEAR (about 2 - 3 gallons or 6 - 7 minutes).
This will clean the system and clear air from the lines.
Additional flushing may be required in some households.
NOTE: As air is cleared from the system, water may spurt out
of the dispenser.
Using the dispenser without the water filter
You can run the dispenser without a water filter cartridge. Your
water will not be filtered. If you run the dispenser without a water
filter cartridge, keep the cartridge cap and replace it in the base
grille for future use.
1. Remove the base grille water filter cartridge (See "Changing a
base grille water filter cartridge" earlier in this section.) Then
slide the cartridge cap off the end of the filter cartridge. DO
NOT DISCARD THE CAP
2. With the cartridge cap in the vertical position, insert the cap
into the base grille until it stops.
The shelves in your refrigerator are adjustable to meet your
individual storage needs. Your model may have glass or wire
shelves.
Storing similar food items together in your refrigerator and
adjusting the shelves to fit different heights of items will make
finding the exact item you want easier. Itwill also reduce the
amount of time the refrigerator door is open, and save energy.
IMPORTANT: Do not clean glass shelves with warm water when
they are cold. Shelves may break if exposed to sudden
temperature changes or impact, such as bumping. For your
protection, tempered glass is designed to shatter into many small
pebble-size pieces. This is normal.
NOTE: Glass shelves are heavy. Use special care when removing
them to avoid impact from dropping.
Slide-out Shelves (on some models)
• To slide out shelf, carefully pull front of shelf toward you.
• To slide in shelf, push shelf in until it stops.
Rotate the cartridge cap to a horizontal position as shown in
step 5.
NOTE: The cartridge cap may not be even with the base
grille.
• ¢
The interior water filter cartridge is located in the upper right-
hand corner of the flesh food compartment of the refrigerator.
The interior water filter cartridge should be replaced every six
months or earlier if the flow of water to your water dispenser or
ice maker decreases noticeably.
Replacing the interior water filter cartridge
1. Twist the interior water filter cartridge 1/4turn to the left. The
INSTALL mark will be lined up with the indicator mark located
on the filter mounting bracket cover.
2. Gently pull down on the cartridge to remove it from the filter
mounting bracket assembly. To prevent water from spilling
inside the refrigerator, DO NOT TIP the cartridge.
To remove and replace a shelf in a metal frame:
1. Pull the shelf forward to the stop.
2. Tilt the front of the shelf up and lift it slightly as you pull the
shelf from the frame.
3. Replace the shelf by guiding it back into the slots on the
frame and pushing the shelf in past the stop.
Shelves and Shelf Frames
To remove and replace a shelf/frame:
11 Remove the shelf/frame by tilting it up at the front and lifting it
out of the shelf supports.
2. Replace the shelf/frame by guiding the rear shelf hooks into
the shelf supports. Tilt the front of the shelf up until rear shelf
hooks drop into the shelf supports.
3. Lower the front of the shelf and check to make sure that the
shelf is securely in position.
3. Dispose of the cartridge.
4. To install a new cartridge, refer to "Installing the interior water
filter cartridge" section in this Use and Care guide.
NOTE: You can run the dispenser without a water filter cartridge.
Your water will not be filtered.
13
.... ,
To slide the shelf from side to side:
1. Lift up on the front of shelf and slide to the desired location.
2. Lower shelf to the level position.
NOTE: You do not have to remove small items from the shelf
before moving it from side to side. You may need to remove larger
items.
To remove the shelf:
NOTE: The shelf is heavy and must be removed using
both hands.
1. Hold the back of the shelf with one hand.
2. Lift the front of the shelf with the other hand to a 45 °angle
and lower it slightly to release it from the upper channel of the
track. Pull the shelf straight out.
To raise the shelf, pull forward on the lever located at the
bottom front of the shelf and liR until the shelf locks into the
vertical position.
To lower the shelf, lower the shelf until it is latched securely
in place.
To raise and lower the shelf:
1. Raise the shelf by first sliding it back and down to make it
half-width. (You can use the shelf in this position to allow
taller items to be stored on the shelf below.)
2. Lift the front of the shelf until it fits securely in place against
the back wall.
3. Lower the shelf securely back into position.
4. Pull the front of the shelf forward until it fits into place.
To remove and replace the shelf track:
11 Remove the shelf track by lifting both sides of the track
slightly and pulling the track straight out.
2. Replace the track by guiding the track hooks into the shelf
support slots on the back wall.
NOTE: Make sure that both sets of track hooks are in the
slots and that the slots are parallel with each other.
3. Push the track back and down securely into the shelf
supports.
To replace the shelf:
NOTE: Make sure that both of the rear shelf slides are securely in
the track before letting go of the shelf. The lateral shelf may be
difficult to install if the track is placed too close to the refrigerator
ceiling. Reposition the track on a lower rung until the shelf can be
tilted enough to easily slide into the track.
1. Hold the shelf at the front and tip the front at a 45 ° angle to
the track.
2. Insert both of the rear shelf slides into the upper channel of
the track, and lower the front of the shelf into place.
The dell drawer stores raisins, nuts, spreads, and other small
items at normal refrigerator temperatures.
To remove and replace the dell drawer:
1. Remove the dell drawer by sliding it straight out to the stop.
Lift the front and slide the drawer out the rest of the way.
2. Replace the dell drawer by sliding it back past the stop.
14
. ._ /=, ....
To remove and replace the crisper and convertible vegetable
meat drawers:
1. Slide crisper or meat drawer straight out to the stop. Lift the
front of drawer with one hand while supporting the bottom of
drawer with other hand and slide the drawer out the rest of
the way.
2. Replace the crisper or meat drawer by sliding it back in fully
past the drawer stop.
IMPORTANT: Do not clean crisper/meat drawer covers with
warm water when they are cold. Covers may break if exposed to
sudden temperature changes or impact, such as bumping. For
your protection, tempered glass is designed to shatter into many
small pebble-size pieces. This is normal.
NOTE: Glass crisper/meat drawer shelves are heavy. Use special
care when removing them to avoid impact from dropping,
To remove and replace the crisper or vegetable/meat
drawer covers:
1. Remove the crisper and meat drawer. Press up in center of
crisper glass insert until it rises above the plastic frame.
Holding the crisper glass firmly, carefully slide the glass insert
forward to remove.
2. Lift crisper cover frame up and remove. Repeat steps to
remove the meat drawer cover.
3. Replace back of meat drawer cover frame into supports on
side walls of the refrigerator and lower the front of the cover
frame into place.
4. Slide rear of glass insert into cover frame and lower front into
place. Repeat steps to replace the crisper cover.
Meat storage guide
Store most meat in original wrapping as long as it is airtight and
moisture-proof. Rewrap if necessary. See the following chart for
storage times. When storing meat longer than the times given,
freeze the meat.
Fresh fish or shellfish ................. use same day as purchased
Chicken, ground beef, variety meat (liver, etc.) ......... 1-2 days
Cold cuts, steaks/roasts ........................................... 3-5 days
Cured meats ........................................................... 7-10 days
Leftovers - Cover leftovers with plastic wrap, aluminum foil, or
plastic containers with tight lids.
Q :ili< sblXIV:TI : :!l_q :i_/:':itt ;"=;_',_='"
...................... 7'11............................... (XVYt _
The convertible vegetable/meat drawer can be adjusted to
properly chill meats or vegetables. The air inside the pan is
cooled to prevent "spot" freezing and can be set to keep meats
at the National Livestock and Meat Board recommended storage
temperatures of 28°- 32°F (-2° - 0°C).
IMPORTANT: To extend freshness, wrap meats in airtight,
moisture-proof materials before storing. Always store meat as
recommended.
Adjusting the control
The convertible control comes preset at the lowest meat setting.
To change a control setting: Move the control to the right
(colder) or to the left (less cold) as desired.
To store vegetables: Set the control at the VEG setting, all the
way to the left, to store vegetables at their optimal storage
temperatures (which need to be warmer than those for meat).
IMPORTANT: If food starts to freeze, move the control to the left
(less cold). Remember to wait 24 hours between adjustments.
Doing so gives the temperature of the food time to change.
You can control the amount of humidity in the moisture-sealed
crisper. Adjust the control to any setting between LOW and
HIGH.
• LOW (open} lets moist air out of the crisper for best storage
of fruits and vegetables with skins.
Fruit: Wash, let dry and store in refrigerator in plastic bag or
crisper. Do not wash or hull berries until they are ready to use.
Sort and keep berries in original container in crisper, or store
in a loosely closed paper bag on a refrigerator shelf.
Vegetables with skins: Place in plastic bags or plastic
container and store in crisper.
• HIGH (closed} keeps moist air in the crisper for best storage
of fresh, leafy vegetables.
Leafy vegetables: Wash in cold water, drain and trim or tear
off bruised and discolored areas. Place in plastic bag or
plastic container and store in crisper.
Humidity control location:
• Humidity Control on crisper drawer (Style 1 - on left)
• Humidity Control on crisper cover (Style 2 - on right)
fL Humidity Control
• .; g% =,
IiIII]I}IFIIIX'(I l..OlItP(}l
I
i)l_si:IIle ) _. s
High 5 4 3 2 I Low
,,ITT£
15
Depending on your model, you may have aone piece utility bin or
a three piece egg bin. To use the three piece egg bin, remove the
cover and place the eggs in the egg tray. Replace cover and store
on an interior refrigerator shelf. If you prefer, you can remove the
egg tray and place the entire carton of eggs in the bin. Replace
the cover.
NOTE: Eggs should be stored in a covered container. If your
model does not have an egg bin or covered utility bin, store
eggs in their original container on an interior shelf.
To remove and replace the wine rack (left) or can/bottle rack
(right):
11 Remove the rack by pulling it straight out from the shelf.
2. Replace the rack by sliding it in between the shelf and the
wall of the refrigerator.
To turn the ice maker on:
The on/off switch for the ice maker is a wire shut-off arm located
on the side of the ice maker. To turn the ice maker on, simply
lower the wire shut-off arm.
NOTE: The ice maker will not make ice until the freezer is cold
enough. Allow 24 hours to produce the first batch of ice. Discard
the first three batches of ice produced.
To turn the ice maker off:
• Automatic turn off: As ice is made, the ice cubes will fill the
ice storage bin. The ice cubes will raise the wire shut-off arm
to the OFF (arm up) position.
• Manual turn off: Lift the wire shut-off arm to the OFF (arm up)
position and listen for the click to make sure the ice maker
will not continue to operate.
• To increase ice production rate: Maximum Ice Production (on
some models): In maximum ice production, the ice maker
should produce approximately 10 to 14 batches of ice in a
24-hour period. If your refrigerator has the maximum ice
production feature, push the switch to MAX.
• Normal Ice Production: In normal ice production mode, the
ice maker should produce approximately 7 to 9 batches of ice
in a 24-hour period. If ice is not being made fast enough, turn
the Freezer Control toward a higher (colder) number in half
number steps. (For example, if the control is at 3, move it to
between 3 and 4.) Wait 24 hours and, if necessary, gradually
turn the Freezer Control to the highest setting, waiting 24
hours between each increase.
Style 1 - Ice Storage Bin
To remove and replace the ice bin:
1, Pull the covering panel out from the bottom and then slide it
back toward the rear.
2. Lift the wire shut-off arm so it clicks into the OFF (up)
position. Ice can still be dispensed, but no more can be
made.
FREEZERFEATURES
Your model may have some or all of these features. Features that
can be purchased separately as product accessories are labeled
with the word "Accessory." Not all accessories will fit all models.
If you are interested in purchasing one of the accessories, please
call the toll-flee number on the cover or in the "Assistance or
Service" section.
Style 1 - Normal and Maximum Ice Maker
f
/
31 Lift up the front of the storage bin and pull it out.
4. Replace the bin by pushing it in all the way or the dispenser
will not work. Push the wire shut-off arm down to the ON
position to restart ice production. Make sure the door is
closed tightly.
Style 2 - Ice Maker
16
To turn the ice maker on:
The ON/OFF switch is located on the top right side of the freezer
compartment. To turn the ice maker on, slide the control to the
ON (left) position.
NOTE: The ice maker will not make ice until the freezer is cold
enough. Allow 24 hours to produce the first batch of ice. Discard
the first three batches of ice produced.
To turn the ice maker off:
• Automatic turn off: The ice maker sensors will automatically
stop ice production but the control will remain in the ON (left)
position.
• Manual turn off: Slide the control to the OFF (right) position.
Style 2 - Ice Storage Bucket
To remove and replace ice bucket:
l i Place four fingers in bucket base opening and rest thumb on
the release button.
2. Holding the base of the bucket with both hands, depress the
release button and lift the bucket up and out. It is not
necessary to turn the ice maker control to the OFF (right)
position. The ice maker will not produce ice without the
bucket installed in the door.
To care for ice storage bin or bucket (Styles 1 and 2)
l i Empty the ice container. Use warm water to melt the ice if
necessary. Never use anything sharp to break up the ice in
the bin or bucket. This can cause damage to the ice container
and the dispenser mechanism.
2. Wash with a mild detergent, rinse well and dry thoroughly. Do
not use harsh or abrasive cleaners or solvents.
REMEMBER:
• Allow 24 hours to produce the first batch of ice.
• Discard the first three batches of ice produced to avoid
impurities that may be flushed out of the system.
• The quality of your ice will be only as good as the quality of
the water supplied to your ice maker.
• Avoid connecting the ice maker to a softened water supply.
Water softener chemicals (such as salt) can damage parts of
the ice maker and lead to poor quality ice. If a softened water
supply cannot be avoided, make sure the water softener is
operating properly and is well maintained.
• It is normal for the ice cubes to be attached at the corners.
They will break apart easily.
• Do not force the wire shut-oft arm up or down.
• Do not store anything on top of the ice maker or in the ice
storage bin.
To remove and replace the shelf:
1. Lift the shelf off of the supports.
2. Slide it out of the shelf support holes.
3. Replace shelf in the reverse order.
Frozen food storage guide
Storage times will vary according to the quality and type of food,
the type of packaging or wrap used (should be airtight and
moisture-proof), and the storage temperature. Ice crystals inside
a sealed package are normal. This simply means that moisture in
the food and air inside the package have condensed, creating ice
crystals.
Put no more unfrozen food into the freezer than will freeze within
24 hours (no more than 2-3 Ib of food per cubic foot [907-1,350 g
per LI of freezer space). Leave enough space in the freezer for air
to circulate around packages. Be careful to leave enough room
for the door to close tightly.
For more information on preparing food for freezing, check a
freezer guide or reliable cookbook.
The freezer basket can be used to store bags of frozen fruits and
vegetables that may slide oft freezer shelves.
To remove and replace the freezer basket:
1. Remove basket by sliding it out to the stop.
2. Lift the front of the basket and slide it out the rest of the way.
31 Replace the basket by positioning it on the side wall guide
rails. Lift the basket front slightly while pushing it past the
guide rail stops and slide basket in the rest of the way.
17
Loading...