Whirlpool GR2SHWXPQ02, GR2SHWXPS02, GR2SHWXPL02, GR2SHWXPB02 Owner’s Manual
REFRIGERATORUSE&CAREGUIDE
MANUALDEUSOYCUIDAI)ODELREFRIGERADOR
GUIDED ILISATION ET D'ENTRETIENDUREFRIGERATEUR
Table of Contents /lndice/Table des mati_res
ASSISTANCE OR SERVICE ............................ 1
REFRIGERATOR SAFETY ............................... 2
INSTALLATION INSTRUCTIONS ................... 3
REFRIGERATOR USE ................................... 12
REFRIGERATOR CARE ................................. 15
TROUBLESHOOTING .................................... 15
WATER FILTER CERTIFICATIONS .............. 17
PRODUCT DATA SHEETS ............................ 18
WARRANTY .................................................... 20
Ifyou need assistance or service, first see the "Troubleshooting"
section. Additional help is available. Call us at 1-800-253-1301
from any_here in the U.S.A., or write:
Whirlpool Corporation
Customer eXperience Center
553 Benson Road
Benton Harbor, MI 49022-2692
In Canada. for installation and service call. 1-800-807-6777.
For assistance call 1-800-461-5681 Monday to Friday 8:00 a.m. -
6:00 p.m. (EST). Saturday 8:30 - 4:30 p.m. (EST). or write:
Whirlpool Canada Inc.
Customer Interaction Center
1901 Minnesota Court
Mississauga, Ontario LSN 3A7
Information may also be obtained by visiting our website at
www.whirlpool.com.
In Canada. visff www.whirlpoolap plia nces.c a.
Please include a daytime phone number in your correspondence.
Keep this book and your sales slip together for future
reference. You must provide proof of purchase or installation
date for in-warranty service.
AYUDA O SERVIC]O TECNICO .................... 21
SEGURIDAD DEL REFRIGERADOR ............ 21
INSTRUCClONES DE INSTALACION .......... 22
USO DE SU REFR]GERADOR ...................... 32
CUIDADO DE SU REFRIGERADOR ............. 35
SOLUCION DE PROBLEMAS ....................... 36
HOJA DE DATOS DEL PRODUCTO ............ 38
GARANTiA ...................................................... 40
Assistance or Service
Write down the following information about your appliance to help
you obtain assistance or service if you ever need it. You will need
to know your complete model number and serial numbe_ You can
find this information on the model and serial number label, Iocsted
on the inside wall of the refrigerator compartment.
Dealer name
Serial number
Address
Phone nul_lber
Model number
Purchase date
Toorder stainless steel cleaner or replacement filters, call
f-800-442-9991 and ask for the part number listed below or
contact your authorized Whirlpool deale_ In Canada, call
1-800-461-5681.
Stainless Steel Cleaner & Polish: Order Part #4396095
Replacement Filter:
Order Part #4396701 (L2OOV/ NL120V / NLC120V)
ASSISTANCE OU SERVICE .......................... 41
SECURITE DU REFRIGERATEUR ................ 41
INSTRUCTIONS D'INSTALLATION .............. 42
UTIUSATION DU REFRIGERATEUR ........... 52
ENTRETIEN DU REFRIGERATEUR ............. 55
DEPANNAGE .................................................. 56
FEUILLES DE DONNEES
SUR LE PRODUIT .......................................... 58
GARANTIE ...................................................... 60
2314473
REFRIGERATORSAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediat e]_
follow instructions.
You can be kilted or seriously injured if you don't follow
instructions,
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: Toreduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:
• Plug into a grounded 3 prong outlet.
• Do not remove ground prong.
• Do not use an adapter.
• Do not use an extension cord.
• Disconnect power before servicing.
• Replace all panels before operating.
• Remove doors from your old refdgerato_
SAVE THESE INSTRUCTIONS
• Use nonflammable cleaner.
• Keep flammable materials and vapors, such as gasoline,
away from refrigerator.
• Use two or more people to move and install refrigerator.
• Disconnect power before installing ice maker (on ice maker
kit ready models only).
• Use a sturdy glass when dispensing ice or water (on some
models).
Proper Disposal of Your Old Refrigerator
IMPORTANT: Child entrapment and suffocation are not problems
of the past. Junked or abandoned refrigerators are still dangerous
- even ifthey wi]] sff for "just a few days." If you are getting rid of
your old refrigerator, please follow these instructions to help
prevent accidents.
Before You Throw Away Your Old Refrigerator or Freezer:
• Take off the doors.
• Leave the shelves in place so that children may not easily
climb inside.
INSTALLATIONINSTRUCTIONS
Remove the Packaging
Do not use sharp instruments, rubbing alcohol, flammable fluids,
or abrasive cleaners to r_move tape or glue. These products can
damage the surface of your refrigerator. For more information, see
"Refrigerator Safely."
IMPORTANT: Do not remove the white foam air return insert from
behind the contro] panel on the ceiling of the refrigerator. If the
insert is removed, ice may migrate do,_¢_ from the freezer and
cause icicles to form.
When Moving Your Refrigerator:
Your refrigerator [s heavy. When moving the refrigerator
for cleaning or service, be sure to protect the floor.
Always pull the refrigerator straight out when moving it.
Do not wiggle or "walk" the refrigerator when trying to move
it, as floor damage could occur.
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from refrigerator.
Failure to do so can result in death, explosion, or fire,
Toensure proper ventilation for your refrigerator, allow for a W"
(1.25 cm) space on each side and at the top. When installing your
refrigerator next to a fixed wall, leave 2" (5.08 cm) minimum
clearance on each side (some models require more) to allow for
the door to swing open. Ifyour refrigerator has an ice maker, allow
extra space at the back for the water line connections.
NOTE: Do not install the refrigerator near an oven, radiator, or
other heat source, nor in a location where the temperature will fall
below 55°F (13°0).
Clean Before Using
After you remove all of the package materials, clean the inside of
your refrigerator before using it. See the cleaning instructions in
"Refrigerator Care."
Important information to know about glass shelves
and covers:
Do not clean glass shelves or covers with warm water when
they are cold. Shelves and covers may break [fexposed to
sudden temperature changes or impact, such as bumping.
For your protection, tempered glass is designed to shatter
into many small, pebble-size pieces. This is normal Glass
shelves and covers are heavy. Use special care when
removing them to avoid impact from dropping.
2,_ ¸
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire_ or electrical shock.
Before you move your refrigerator into its final location, it is
important to make sure you have the proper electrical connection.
Recommended Grounding Method
A 115 Volt, 60 Hz., AC only 15- or 20-amp fused, grounded
electrical supply is _quired. It is recommended that a separate
oi_uit serving only your _frigerator be provided. Use an outlet
that cannot be turned off by a switch. Do not use an
extension cord.
NOTE: Before performing any type of installation, cleaning, or
removing a light bulb, turn the control (Thermostat, Refrigerator or
Freezer Control depending on the model) to OFF and then
disconnect the refrigerator from the electrical source. When you
are finished, reconnect the refrigerator to the electrical source and
reset the control (Thermostat, Refrigerator or Freezer Control
depending on the model) to the desired setting.
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
IMPORTANT:
• If you turn the refrigerator on before the water line is
connected, turn the ice maker OFR
• All installations must meet local plumbing code requirements.
• Use copper tubing and check for leaks. Install copper tubing
only in areas where the household temperatures will remain
above freezing.
TOOLS NEEDED: Flat-blade screwdriver, 7A_,,and V," open-end
wrenches or two edjustable wrenches, %" nut driver and drill bit,
hand drill or electric drill (properly grounded).
NOTE: Your refrigerator dealer has a kit available with a _/4"
(6.35 ram) saddle-type shutoff valve, a union, and copper tubing.
Before purchasing, make sure a saddle-type valve complies with
your local plumbing codes. Do not use a piercing-type or 3/18"
(4.76 ram) saddle valve which reduces water flow and clogs more
easily.
Water Pressure
A cold water supply with water pressure of between 30 and
120 psi (207 - 827 kPa) is required to operate the water dispenser
and ice maker. If you have questions about your water pressure,
call a licensed, qualified plumber.
Reverse Osmosis Water Supply
IMPORTANT: The pressure of the water supply coming out of a
reverse osmosis system going to the water inlet valve of the
refrigerator needs to be between 30 and 120 psi (207 - 827 kPa).
If a reverse osmosis water filtration system is connected to your
cold water supply, the water pressure to the reverse osmosis
system needs to be a minimum of 40 to 60 psi (276 - 414 kPa).
If the water pressure to the reverse osmosis system is less than
40 to 60 psi (276 - 414 kPa):
• Check to see whether the sediment filter inthe reverse
osmosis system is blocked. Replace the filter if necessary.
• Allow the storage tank on the reverse osmosis system to refill
after heavy usage.
• g your refrigerator has a water filtar cartridge, it may further
reduce the water pressure when used in conjunction with a
reverse osmosis system. Remove the water filter cartridge.
See "Water Filtration System."
If you have questions about your water pressure, call a licensed,
qualified plumber.
Read all directions before you begin.
IMPORTANT: Ifyou turn the refrigerator on before the water line is
connected, turn the ice maker OFR
Connect to Water Line
f. Unplug refrigerator or disconnect power.
2. Turn OFF main water supply. Turn ON nearest faucet long
enough to clear line of water.
3. Locate a _62"to 1V4"(1.25 cm to 3.18 ore) vertical cold water
pipe near the refrigerator.
IMPORTANT:
• Make sure it is a cold water pipe.
• Horizontal pipe will work, but drill on the top side of the
pipe, not the bottom. This will help keep water away from
the drill and normal sediment from collecting in the valve.
4. Datermine the length of copper tubing you need. Measure
from the connection on the lower left rear of refrigerator to the
water pipe. Add 7 ft. (2.1 m) to allow for cleaning. Use _/4"
(6.35 ram) O.D. (outside diameter) copper tubing. Be sure both
ends of copper tubing are cut square.
5. Using a grounded drill, drill a _/4"hole in the cold water pipe
you have selected.
F E D
A Cold water pipe E Compression sleeve
B Pipe clamp _ Shutoff valve
C Copper tubing G Packing nut
D Compression nut
6. Fasten the shutoff valve to the cold water pipe with the pipe
clamp. Be sure the outlet end is solidly in the ¼" drilled hole in
the water pipe and that the washer is under the pipe clamp.
Tighten the packing nut. Tighten the pipe clamp screws
carefully and evenly so washer makes a watertight seal. Do
not overtighten or you may crush the copper tubing.
7, Slip the compression sleeve and compression net onto the
copper tubing as shown. Insert the end of the tubing into the
outlet end squarely as far as it will go. Screw compression nut
onto outlet end with adjustable wrench. Do not overtighten.
8, Place the free end of the tubing in a container or sink, and turn
ON the main water supply. Flush the tubing until water is clear.
Turn OFF the shutoff valve on the water pipe. Coil the copper
tubing.
Connect to Refrigerator
Style 1
1. Unplug refrigerator or disconnect power.
2, Attach the copper tube to the valve inlet using a compression
nut and sleeve as shown. Tighten the compression nut. Do not
overtightan.
3, Use the tube clamp on the back of the refrigerator to secure
the tubing to the refrigerator as shown. This will help prevent
damage to the tubing when the refrigerator is pushed back
against the wall.
4, Turn shetoff valve ON.
5. Check for leaks. Tighten any connections (including
connections at the valw or nuts that leak.
A ¼" x ¼" coupling is needed in order to connect the water
tubing to an existing household water line. Thread the
provided nut onto the coupling on the end of the copper
tubing.
NOTE: Tighten the nut by hand. Then tighten itwith awrench
two more turns. Do not overtightan.
A c D
A Water tubing D Coupling (provided)
B Nut (provided) E Ferrule (purchased)
G Bulb F: Nut (purchased)
4. Turn shutoff valve ON.
5. Check for leaks. Tightan any nets or connections (including
connections at the valve) that leak.
6. Plug in refrigerator or reconnect power.
7. Flush the weter systam. See "Weter Dispenser."
NOTE: Allow 24 hours to produce the first batch of ice. Discard
the first three batches of ice produced. Allow 3 days to completely
fill ice container.
Style 3
f. Unplug refrigerator or disconnect power.
2. Remove the shipping tape from the gray, coiled weter tubing
on the rear of the refrigerator.
3. Thread the provided nut onto the weter valve as shown.
NOTE: Tighten the nut by hand. Then tighten it with a wrench
two more turns. Do not overtightan.
A Tubeclamp C Compression nut
B Coppertubit)g D Valveinlet
6. The ice maker is equipped with a builtqn t, eter strainer. If your
water conditions require a second water strainer, install it in
the ¼" (6.35 ram) water line at either tube connection. Obtain
awater strainer from your nearest appliance dealer.
7. Plug in refrigerator or reconnect power.
8. Flush the water system. See "Water Dispenser."
NOTE: Allot, 24 hours to produce the first batch of ice. Discard
the first three batches of ice produced. Allot, 3 days to completely
fill ice container.
Style 2
1. Unplug refrigerator or disconnect power.
2. Remove the shipping tape from the gray, coiled water tubing
on the rear of the refrigerator.
A
B
A Bulb
B Nut (provided)
4. Turn shutoff valve ON.
5. Check for leaks. Tightan any nets or connections (including
connections at the valve) that leak.
6. Plug in refrigerator or reconnect pot, er.
7. Flush the weter systam. See "Weter Dispenser."
NOTE: Allow 24 hours to produce the first batch of ice. Discard
the first three batches of ice produced. Allot, 3 days to completely
fill ice container.
TOOLS NEEDED: 5/_o"hex-heed socket wrench, #2 PMIlips
screwdriver, flat-blade screwdriver, 5_6"open-end wrench,
flat 2" putty knife.
IMPORTANT:
• Unplug refrigerator or disconnect power.
• Turn oft the water supply to the refrigerator. If there iswater in
the dispenser's water line, some spilling may occur during
door swing reversal.
• Remove food and any adjustable door or utility bins from
doors.
• If you only want to remove and replace the doors, see
"Remove Doors and Hinges" and "Replace Doors and
Hinges."
• All graphics referenced in the following instructions are
included later in this section after "Final Steps."
Remove Doors and Hinges
ReverseDoors (optional)
IIMPORTANT:
• If you want to reverse your doors so that they open in the
opposite direction, follow these steps. If you are not
reversing the doors, see "Replace Doors and Hinges."
• The the grapMcs shown are for a right-hand swing
refrigerator (hinges factory installed on the righ9.
Door Stop Screw
DoorHandle Sealing Screw
Flat=Head Handle Screw
DoorHinge Hole Plug
Cabinet Hinge Hole Plug
Door Handle Screw Cover
1. Unplug refrigerator or disconnect power.
2. Turn off the water supply to the refdgeratar.
3. Open refdgeratar door and remove base grille from the bottom
front of the refrigerator. See Graphic 1.
4. Close the refrigerator door and keep both doors closed until
you are ready to lift them free from the cabinet.
NOTE: Provide additional support for the doors while the
hinges are being moved. Do not depend on the door magnets
to hold the doors in place while you are working.
5. Pull the water dispenser wire/tube assembly out of the
channel on the bottom of the refrigerator door. See Graphic 2.
6. Disconnect the wiring plug. See Graphic g.
7. Disconnect the water dispenser tubing. Press the red outer
ring against the face of the fitting and pull the dispenser tu bing
free. See Graphic 16.
8. Remove the parts for the top hinge. See Graphic 4. Lift the
freezer door free from the cabinet.
g. Remove the %e" hex-heed screw from the center rail. Loosen
the two screws on the side just enough to remove the center
hinge. Remove the center hinge. Replace the center rail screw
and tighten all screws. See Graphic 5.
fO. Lift the refrigerator door free from the cabinet.
f f. Remove the parts for the bottom hinge. See Graphic 6.
Door Handle Seal Screw Front
Round=Head Handle Screw
Freezer Door
If the door hinges were factory installed on the le_hand side of
the refrigerator, these graphics are reversed.
f. Remove the cabinet hinge hole plugs from the cabinet top and
move them to the opposite side hinge holes. See Graphic 7.
2. Remove freezer handle assembly as shown. Keep all parts
together. See Graphic 8.
3. Remove door hinge hole plug. Move to opposite side as
shown in Graphic 9.
4. Remove door handle sealing screws. Move to opposge side of
freezer door as shown in Graphic 1g.
5. Remove door stop. Move to opposita side of freezer door as
shown in Graphic 11.
6. Position handle on opposita side of freezer door. Assemble
handle on door as shown in Graphic 8.
7. Tighten all screws. Set aside door until Mnges and refrigerator
compartment door are in place.
Right-Hand Swing to Le_t-Hand Swing
If the door hinges were factory-installed on the right-hand side of
the refrigerator, follow these instructions.
f. Remove refrigerator handle bottom tdm. For Style 1,slide tdm
down as shown in Graphic 13. For St}de 2, remove the handle
screw cover. See Graphic 14.
2. Remove refrigerator handle assembly as shown. Keep all
parts together. See Graphic 14.
3. Remove door hinge hole plug from refrigerator door. Move to
opposite side hinge hole as shown in Graphic 9.
4. Remove door handle sealing screws. Move to opposge side of
refrigerator door as shown in Graphic 10.
5. Remove door handle seal screw front. Move to opposffe side
of refrigerator door as shown in Graphic 12.
6. Remove door stop. Move to opposge side of refrigerator door
as shown in Graphic 11.
7. Positionrefrigeratorhandleonoppositesideoftherefrigerator
doorasshowninGraphic14.Drivetoptwoscrewsinhandle
first.Alignlowerportionofhandleanddrivebottomscrew.
8. Alignrefrigeratorbottomtdm.ForStyle1,slidetriminto
place.SeeGraphic13.ForStyle2,replacethedoorhandle
screwcover.BeeGraphic14.
g. Onthebottomoftherefrigeratordoor,movethewire/tube
assemblysotheconnectorpointstowardtheopposffe
(bottom-hinge)side.BeeGraphic2.
f0.Locatethewaterdispenserwire/tubeassemblybehindthe
left-handsideofthebottomrail.Breakthetapeandpullthe
looseendoutfromthebottomrail.BeeGraphic15.
ff. Unscrewthehoseclipfromtheright-handsideofthebottom
railandremoveit.Replacethehoseclip(withthetabpointing
down)ontheleft-handsidewire/tubeassembly.Bee
Graphic17.
IMPORTANT:Donotcompletelytightenthehosecliptothe
bottomrailatthistime.
12.Connecttheright-handsidedispenserwire/tubeassemblyto
theconnectorslocatedneartheright-handsideofthewater
filter.Pushtheconnectorsandwire/tubeassemblybehindthe
bottomrail.SeeGraphic15.
fg.Goto"ReplaceDoorsandHinges."
Left-HandSwing to Right-Hand Swing
Ifthe refrigerator doors have already been reversed to left-hand
swing and you wish to change to a right-hand swing, follow these
steps. Some graphics may be reversed.
f. Remove refrigerator handle bottom trim. For Style 1, slide trim
down as sho_q in Graphic 1g. For Style 2, remove the handle
screw cover. Bee Graphic 14.
2. Remove refrigerator handle assembly as shown. Keep all
parts together. See Graphic 14.
3. Remove door hinge hole plug from refrigerator door. Move to
opposite side hinge hole as shown in Graphic 9.
4. Remove door handle sealing screws. Move to opposite side of
refrigerator door as shown in Graphic 10.
5. Remove door ha_dle seal screw front. Move to opposite side
of refrigerator door as shown in Graphic 12.
6. Remove door stop. Move to opposite side of refrigerator door
as shown in Graphic 11.
7. Position refrigerator handle on opposite side of the refrigerator
door as shown in Graphic 14. Drive top two screws in handle
first. Align lower portion of handle and drive bottom screw.
8. On the bottom of the refrigerator door, move the wire/tube
assembly so the connector points toward the opposffe
(bottom-hinge) side. See Graphic 2.
g. Push the left-hand side dispenser wire/tube assembly behind
the bottom rail. It will not be reconnected. Bee Graphic 15.
tO. Unscrew the hose clip from the left-hand side of the bottom
rail and remove it. Replace the hose clip {with the tab pointing
down) on the right-hand side wire/tube assembly. See
Graphic 17.
IMPORTANT: Do not completely tighten the hose clip to the
bottom rail at this time.
f f. Disconnect the dispenser tubing and wiring plug from the
connectors located near the right-hand side of the water filter.
Push the wiring plug and connector tube behind the bottom
rail. They will not be reconnected. The wire/tube assembly will
reconnect later with the door. Bee Graphic 15.
12. Go to "Replace Doors and Hinges."
Replace Doers and Hinges
NOTE: Graphic may be reversed ifdoor swing is reversed.
f. Assemble the parts for the bottom hinge as shown. Tighten
screws. Bee Graphic 6.
2. Replace the refrigerator door.
NOTE: Provide additional support for the doors while the
hinges are being moved. Do not depend on the door magnets
to hold the doors in place while you are working.
3. Remove the _/_6"hex-head screw from the center rail. Loosen
the two screws on the side just enough to replace the center
hinge. Replace the center hinge. Replace the center rail screw
and tighten all screws. Bee Graphic 5.
4. Reconnect the wiring plug. See Graphic 3.
5. Reconnect the water dispenser tubing by pushing the tubing
into the fitting until itstops and the black mark touches the
face of the red outer ring. See Graphic 16.
6. Carefully push the wire/tube assembly into the clips on the
bottom of the refrigerator door. See Graphic 2.
7. Replace the freezer door.
8. Assemble the parts for the top hinge as shown. Do not tighten
completely. See Graphic 4.
g. Line up the doors so that the bottom of the freezer door aligns
evenly w_h the top of the refrigerator door. Tighten all screws.
f0. Open the refrigerator door a full 120°. Locate the black
electrical tape on the wire/tube assam bly. Make sure the hose
clip is covering the tape and tighten the hose clip completely.
See Graphic 17.
Final Steps
f. Check all holes to make sure that hole plugs and screws are in
place. Reinstall top hinge cover. Bee Graphic 4.
2. If the door swing is reversed, remove the bottom hinge cover
from the left-hand side of the base grille and replace it on the
opposite side. Replace the base grille. See Graphic 1.
g. Plug in refrigerator or reconnect power.
4. Turn on the water supply to the refrigerator.
NOTE: Make sure the water dispenser tube connections, at
the bottom of the refrigerator door, are fully tightened.
5. Flush the water system. See "Water Filtration System."
6. If the dispenser light is not working, recheck the wiring plug
connection.
7. Return all removable door parts to doors and food to
refrigerator.
BaseGrille
A Bottom H#lge Cover
• c'&_
I
A Cabinet H_nge Hole Plugs
I
A Door H_nge Hole Plug
A
A Flat-Head Handle Screws
B Freezer Handle
A Ooor Handle Seahng Screws
Front View Side V_e_t
Top Hinge
Center Hinge
A %_" HO._Head Hing9 Screws
B CentefH#lge
Bottom Hinge
d, , I
A DoorStopSerew A B
B Door Stop
A
A Flat-Head
Handle Screw
B Refrigerator Handle
C Handle Screw
D_ Door Handle Screw
Cover
Ooor Handle
Seal Screw Front
A Roht Wife/Tube A
B Left Wsfe/Tube A Red Outer Rblg A Hose C#p
TOOLS NEEDED: 5/_o"hex-heed socket wrench, #2 Phillips
screwdriver, flat-blade screwdriver, 5/t0"open-end wrench,
flat 2" putty knife.
IMPORTANT:
• Unplug refrigerator or disconnect power.
• Turn oft the water supply to the refrigerator. If there is water in
the dispenser's water line, some spilling may occur during
door swing reversal.
• Remove food and any adjustable door or utility bins from
doors.
• If you only want to remove and replace the doors, see
"Remove Doors and Hinges" and "Replace Doors and
Hinges."
• All graphics referenced in the following instructions are
included later in this section after "Final Steps."
Remove Doors and Hinges
_J' Hex head hinge screw
f. Unplug refrigerator or disconnect power.
2. Turn off the water supply to the refdgeratar.
3, Open the refrigerator door and remove the base grille from the
bottom front of the refrigerator. See Graphic 1.
4, Close the refrigerator door and keep both doors dosed until
you are ready to lift them free from the cabinet.
NOTE: Provide additional support for the doors while the
hinges are being moved. Do not depend on the door magnets
to hold the doors in place while you are working.
5, Pull the water dispenser wire/tube assembly out of the
channel on the bottom of the refrigerator door. See Graphic 2.
6, Disconnect the wiring plug. See Graphic g.
7, Disconnect the water dispenser tubing. Press the red outer
ring against the face of the fitting and pull the dispenser tu bing
free. See Graphic 11.
NOTE: There may be water in the dispenser tubing if the
dispenser has been used.
8, Remove the parts for the top hinge. See Graphic 4. Lift the
freezer door free from the cabinet.
g, Remove the %e" hex-heed screw from the center rail. Loosen
the two screws on the side just enough to remove the center
hinge. Remove the center hinge. Replace the center rail screw.
See Graphic 5.
tO, Lift the refrigerator door free from the cabinet.
f f, Remove the parts for the bottom hinge. See Graphic 6.
ReverseDoors (optional)
IMPORTANT:
• If you want to reverse your doors so that they open in the
opposite direction, follow these steps. If you are not reversing
the doors, see "Replace Doors and Hinges."
• The the graphics shown are for a fight-hand swing refrigerator
(hinges factory installed on the right).
Round-Head Door Handle DoorHinge
Handle Screw ScrewHole Plug Hole Plug
Right-Hand Swing to Le_t-Hand Swing
If the door hinges were factory installed on the right-hand side of
the refrigerator, follow these steps.
f, Remove cabinet hinge hole plugs from the cabinet top and
move them to opposite side hinge holes. See Graphic 7.
2, Remove door hinge hole plug from top of freezer door. Move
to opposite side as shown. See Graphic 8.
3, Remove door stap from both the freezer and refrigerator
doors and place them on the opposite side. See Graphic 9.
4, On the bottom of the refrigerator door, move the wire/tube
assembly so the connector points toward the opposite
(bottom-hinge) side. See Graphic 2.
5. Locate the watar dispenser wire/tube assembly behind the
left-hand side of the bottom rail. Break the tape and pull the
loose end out from the bottom rail. See Graphic 10.
6, Unscrew the hose clip ftom the right-hand side of the bottom
rail and remove it. Replace the hose clip (with the tab pointing
down) on the left-hand side wire/tube assembly. See
Graphic 12.
IMPORTANT: Do not completely tighten the hose clip to the
bottom rail at this time.
7. Connect the right-hand side dispenser wire/tube assembly to
the connectors located near the right-hand side of the water
filter. Push the connectors and wire/tube assembly behind the
bottom rail. See Graphic 10.
8, Go to "Replace Doors and Hinges."
Left-HandSwing to Right-Hand Swing
Ifthe refrigerator doors have already been reversed to left-hand
swlag and you wish to change back to a right-hand swing, follaw
these steps.
1, Remove cabinet hinge hole plugs from the cabinet top and
move them to opposite side hinge holes. See Graphic 7.
2, Remove door hinge hole plug from top of freezer door. Move
to opposffe side as shown. See Graphic 8.
3, Remove door stop from both the freezer and refrigerator
doors and place them on the opposffe side. See Graphic 9.
4, On the bottom of the refrigerator door, move the wire/tube
assembly so the connector points toward the opposffe
(bottom-hinge) side. See Graphic 2.
5. Push the left-hand side dispenser wire/tube assembly behind
the bottom rail. It will not be reconnected. See Graphic 10.
6, Unscrew the hose clip from the laft-hand side of the bottom
rail and remove it. Replace the hose clip (with the tab pointing
down) on the right-hand side wire/tube assembly. See
Graphic 12.
IMPORTANT: Do not completely tighten the hose clip to the
bottom rail at this time.
7. Disconnect the dispenser tubing and wiring plug from the
connectors located near the right-hand side of the water filter.
Push the widng plug and connector tube behind the bottom
rail. They will not be reconnected. The wire/tube assembly will
reconnect later with the door. See Graphic 11.
8, Go to "Replace Doors and Hlages."
Replace Doors and Hinges
NOTE: Graphics and steps may be reversed if the door swing is
reversed.
f, Assembla the parts for the bottom hinge as shown. Tighten all
screws. See Graphic 6.
2, Replace the refrigerator door.
NOTE: Provide additional support for the doors while the
hinges are being moved. Do not depend on the door magnets
to hold the doors in place whila you areworking.
3. Remove the %0" hex-head screw from the center rail. Loosen
the two screws on the side just enough to replace the center
hinge. Replace the center hinge and center rail screw. Tighten
all screws. See Graphic 5.
4, Reconnect the wMng plug. See Graphla 3.
5, Reconnect the water dispenser tubing by pushing the tubing
into the fitting until itstops and the black mark touches the
face of the red outer ring. See Graphic 11.
6, Carefully push the wire/tube assemMy into the clips on the
bottom of the refrigerator door. See Graphic 2.
7, Replace the freezer door.
8, Assembla the parts for the top hinge as shown. Do not tighten
completely. See Graphic 4.
g, Line up the doors so that the bottom of the freezer door aligns
evenly with the top of the refrigerator door. Tighten all screws.
f0, Open the refrigerator door a full 120°. Locate the black
electrical tape on the wire/tube assam bly. Make sure the hose
clip is covering the tape and tighten the hose clip completely.
See Graphic 12.
Final Steps
f, Check aHholds to make sure that hold plugs and screws are la
place. Reinstall top hinge cover. See Graphic 4.
g, If the door swlag is reversed, remove the bottom hinge cover
from the left-hand side of the base grille and replace it on the
opposite side. Replace the base grille. See Graphic 1.
3, Plug in refrigerator or reconnect power.
4, Turn on the water supply te the reftigerator.
NOTE: Make sure the water dispenser tube connections, at
the bottom of the refrigerator door, are fully tightened.
5, Flash the water system. See "Water Filtratlan System."
6, If the dispenser light is not worklag, recheck the wiring plug
connection.
7, Return all removabla door parts to doors and food to
refrigerator.
10
Base Grille
A Bottom Hhl_e Cover
A WIf#lg Plug
I
A Cabinet Hinge Hole Plugs
A DoorHmge Hole PJug
Top Hinge
A Top H_lge Cover
B %_" Hex Head H#)ge Screws
C Top H#)ge
Center Hinge
-J B
A %_"HexHead Hsng_ S#fews
B Cot)tel H#)_
Bottom Hinge
F_ont View
A B A
0
Side View
A DoorStop
_ DoorStop Screw
B %_" Hex Head Hinge ._rew8
A Roht Witeflube A
B Left Wsteflube A Red Outer Ri/_ A Hose Clip
11
Mid-setting "3"
_r÷
Door Closing
Your refrigerator has two front adjustable rollers - one on the right
and one on the left. If your refrigerator seems unsteady or you
want the doors to close easier, adjust the refrigerator's tilt using
the instructions below:
f, Plug into a grounded 3 prong outlet.
2, Move the refrigerator into its final location.
3, Remove the base grille. See Base Grille graphic. The two
leveling screws are part of the front roller assemblies which
are at the base of the refrigerator on either side.
4. Use a screwdriver to adjust the leveling screws. Turn the
leveling screw to the right to raise that side of the refrigerator
or turn the leveling screw 1o the left to lower that side. It may
take several turns of the leveling screws to adjust the tilt of the
refrigerator.
NOTE: Having someone push against the top of the
refrigerator takes some weight off the leveling screws and
rollers. This makes it easier to adjust the screws.
5. Open both doors again and check to make sure that thay
close as easily as you like. If not, tilt the refrigerator slightly
more to the rear by turning both leveling screws to the right. It
may take several more turns, and you should turn both
leveling screws the same amount.
6, Replace the base grille.
Align Doors
Ifthe space between your doors looks uneven, you can adjust it
using the instructions below:
f, Pry off the top hinge cove_
2, Loosen the top hinge screws using a %B"socket or wrench.
3, Have someone hold the door in place or put a spacer between
the doors ,_ile you tighten the top hinge screws.
4, Replace the top hinge cove_
REFRIGERATORUSE
For your convenience, your refrigerator controls are preset at the
factory. When you first install your refrigerator, make sure that the
controls are still preset to the mid-settings as sho,_¢_.
NOTE: To turn your refrigerator off, turn the refrigerator control to
the word OFF or until the word OFF appears. Your product will not
cool ,_hen the refrigerator control is set to OFE
s i
Mid-setting "3"
\8 .....
Mid-setting "4"
IMPORTANT:
• Give your refrigerator time to cool down completely before
adding food. It is best to wait 24 hours before you put food
into the refrigerator.
• If you add food before the refrigerator has cooled completely,
your food may spoil. Adjusting the Refrigerator and Freezer
Controls to a higher (colder) than recommended setting will
not cool the compartments any faster.
Adjusting Controls
The mid-settings indicated in the previous section should be
correct for normal household usage. The controls are set correctly
when milk or juice is as cold as you like and when ice cream is
firm.
Ifthe temperature is too warm or too cold in the refrigerator or
freezer, first check the air vents to be sure they are not blocked.
If you need to adjust temperatures, use the settings listed in the
chart below as a guide. On models with two controls, adjust the
refrigerator temperature first. Wait at least 24 hours between
adjustments and then recheck the temperatures.
CONDITION/R EASON: ADJUSTMENT:
REFRIGERATOR too warm REFRIGERATOR or
TEMPERATURE Control one
setting higher
FREEZER too warm/too FREEZER or TEMPERATURE
little ice Control one setting higher
MAX ice production switch
REFRIGERATOR too cold REFRIGERATOR or
TEMPERATURE Control one
setting lower
FREEZER too cold FREEZER or TEMPERATURE
Control one setting lower
12
You can control the amount of humidly in the moieture-sealed
crisper. Adjuet the control to any setting between LOW and HIGH.
LOW (open) for best storage of fruits and vegetables with skins.
HIGH (closed) for best storage of fresh, leafy vegetables.
Tumi_j the Ice Maker OrJOff
To turn the ice maker ON. simply lower the wire shutoff arm.
To manually turn the ice maker OFE (iff the wire shutoff arm to the
OFF (arm up) position and listen for the click.
NOTE: Your ice maker has an automatic shutoff. As ice is made.
the ice cubes wiil fill the ice storage bin and the ice cubes will
raise the wire shutoff arm to the OFF (arm up) position. Do not
force the wire shutoff arm up or down.
\
IceProduction Rate
• Allow 24 hours to produce the first batch of lee. Discard the
first three batches of ice produced.
• The ice maker should produce approximetely 8 to 12 batches
of ice in a 24-hour period.
• To increase ice production, lower the freezer and refrigerator
temperature. See "Using the Controls." Wait 24 hours
between adjustments.
• For maximum ice production (on some models), push the
sedtch to ICE PLUS. The ice maker should produce 16 to
20 batches of ice in a 24-hour period in the Ice Plus mode.
Cut Hazard
Use a sturdy glass when dispensing ice or water,
Failure to do so can result in cuts.
IMPORTANT:
• Ifyou did not flush the water system when the refrigerator was
first installed, press the water dispenser paddle with a glass or
jar until you draw and discard 2 to 3 gal. (8 to 12 L) or
approximately 5 minutas of water after water begins
dispensing. It will take 3 to 4 minutas for the water to begin
dispensing. The water you draw and discard cleans the
system and helps clear air from the lines. Allow several hours
for the refrigerator to cool down and chill water.
NOTE: After 4 minutes of continuous dispensing, the
dispenser will stop dispensing to avoid flooding. To continue
dispensing, r&move the glass and press the dispensing
paddle again.
• When the refrigerator compartment door is open, the
dispenser will not dispense water and the dispenser control
panel will not display or receive input. The previous settings
will be retained.
Dispense Water
f. Press a sturdy glass againet the paddle to etart dispensleg.
2. Release pressure on the paddle and be sure the weter has
stopped dispensing before removing the glass.
NOTE: Water may have an off-flavor if you do not use the
dispenser periodically. Dispense enough water every week to
maintain a fresh supply.
Remember
• The quality of your ice will be only as good as the quality of the
water supplied to your ice maker. Avoid connecting the ice
maker to a softened water supply. Water softener chemicals
(such as salt) can damage parts of the ice maker and lead to
poor quality ice. If a softened water supply cap,not be avoided.
make sure the water softener is operating properly and is well
maintained.
• Never use anything sharp to break up the ice in the bin. This
can cause damage to the ice container and the dispenser
mechanism.
• Do not store anything on top of or in the lee maker or ice bin.
Remove and Replace Dispenser Paddle
The removable paddle is designed to catch small spills and allow
for easy cleaning. There is no drain in the paddle. The paddle can
be removed from the dispenser to be emptied or cleaned.
IMPORTANT: Press and hold LOCK OUT for 2 seconds to
activate the dispenser lock feature before removing the dispenser
peddle. See "The Dispenser Lock."
13
f. Press up on the dispenser paddle, as shown, to release.
2. Pull down on the dispenser paddle to remove.
NIGHT LIGHT: Press the light bulb button asecond time to select
the night light mode. The green indicator will appear below NIGHT
LIGHT. The dispenser light will automatically adjust to become
brighter as the room brightens, dimmer as the room darkens.
OFF: Press the light bulb button a third time to turn the dispenser
light off.
The Dispenser Lock
The watar dispenser can be locked for easy cleaning or to prevent
unintentional dispensing by small children and pets.
NOTE: The lock feature does not shut off power to the product, to
the ice maker, or to the dispenser light. It simply deactivates the
dispenser paddle.
To Lock the Dispenser:
Press and hold the LOCK OUT button for 2 seconds until the red
indicator appears. The water dispenser and the dispenser control
panel will not work.
To Unlock the Dispenser:
Press and hold the LOCK OUT button for 2 seconds until the
indicator disappears. Then continue to dispense water as usual.
3. Replace the dispenser paddle by firmly snapping it intothe
dispenser cover as shown.
The Dispenser Light
The dispenser light turns on automatically when you press the
paddle to dispense water. If you want the light to be on
continuously, press the light bulb button, located on the left-hand
side of the dispenser control panel, for either ON or NIGHT LIGHT.
NOTE: The dispenser lights are LEDs which do not need to be
changed.
NI_H_
• ®
t/G£1
ON: Press the light bulb button once to turn on the dispenser
light. The green indicator will appear below ON.
LOCKOUT
NOTE: Do not use with water that is microbiologically unsafe
or of unknown quality without adequate disinfection before or
after the system. Systems certified for cyst reduction may be
used on disinfected waters that may contain filterable cysts.
Water Filter Status Light (on some models)
The water filter status light will help you know when to change
your water filter. The light will change from green to yellow. This
tells you that it is almost time to change the filter. It is
recommended that you replace the water filter when the status
light changes to red OR water flow to your watar dispenser or ice
maker decreases noticeably.
After changing the water filter, reset the water filter status light.
The status light will change from red to green when the system is
reset.
Non-indicator Water Filter (on some models)
If your refrigerator does not have the status light, you should
change the water filter every 6 to 9 months depending upon your
usage. If the water flow to the water dispenser or ice maker
decreases noticeably before 6 months have passed, replace the
water filter more often.
Using the Dispenser Without _ Water Filter
You can run the dispenser without a watar Jilter. Your watar will not
be filtered.
f, Remove the water tiger.
2, Slide the cap off the end of the filter and replace the cap in the
base grille.
IMPORTANT: Do not discard the cap. It is part of your
refrigerator. Keep the cap to use with the replacement filter.
3, Rotate the cap until it is securely in posgion.
14
REFRIGERATORCARE
Explosion Hazard
Use nonflammable cleaner.
Failure to do so can result in death_ explosion_ or fire,
Both the refrigerator and freezer sections defrost autometically.
However, clean both sections about once a month to prevent
odors from building up. Wipe up spills immediately.
IMPORTANT: Because air circulates between both sections, any
odors formed in one section will transfer to the other. You must
thoroughly clean both sections to eliminate odors. To prevent
odor transfer and drying out of food, wrap or cover foods tightly.
To Clean Your Refrigerator:
NOTE: Do not use abrasive or harsh cleaners such as window
sprays, scouring cleansers, flammable fluids, cleaning waxes,
concentrated detergents, bleaches or cleansers containing
petroleum products on plastic parts, interior and door liners or
gaskets. Do not use paper towels, scouring pads, or other harsh
cleaning tools.
f, Unplug refrigerator or disconnect power.
2, Hand wash, rinse, and dry removable parts and interior
surfaces thoroughly. Use a clean sponge or soft cloth and a
mild detergent in warm water.
g,
Wash stainless steel and painted metal exteriors with a clean
sponge or soft cloth and a mild detergent in warm water.
4,
There is no need for routine condenser cleaning in normal
home operating environments. If the environment is
patticulady greasy or dusty, or there is significant pet traffic in
the home, the condenser should be cleaned every 2 to
3 months to ensure maximum efficiency.
If you need to clean the condenser:
• Removethe base grille.
• Use a vacuum cleaner with a soft brush to clean the grille,
the open areas behind the gdlle and the front surface area
of the condenser.
• Replace the base grille when finished.
Plug in refrigerator or reconnect power.
NOTE: Not all bulbs will fit your refrigerator. Be sure to replace the
bulb with one of the same size, shape, and wattage.
f, Unplug refrigerator or disconnect powe_
2, Remove the bulb from behind the control panel inthe
refrigerator or from behind the light shield in the freezer (on
some models). Replace it with a bulb of the same wattage.
3, Plug in _frigeretor or reconnect powe_
\
ta
TROUBLESHOOTING
Try the solutions suggested here first in order to avoid the cost of an unnecessary ser4ce call.
The refrigerator will not operate
• Power cord unplugged? Plug into a grounded 3 prong outlet.
• Is outlet working? Plug in a lamp to see if the outlet is
working.
• Household fuse blown, or circuit breaker tripped? Replace
the fuse or reset the circuit breaker.
• Are controls on? Make sure the refrigerator controls are on.
See "Using the Controls."
• Hew installation? Allow 24 hours following installetion for the
refrigerator to cool completely.
NOTE: Adjusting the temperature controls to coldest setting
will not cool either compartment more quickly.
]]_e motor seems tO run tOO much
Your new refrigerator may run longer than your old one due to its
high-efficiency compressor and fans. The unit may run even
longer if the room is warm, a large food load is added, doors are
opened often, or if the doors have been left open.
The refrigerator seems noisy
Refrigerator noise has been reduced over the years. Due to this
reduction, you may hear intermittent noises from your new
refrigerator that you did not notice from your old model. Below are
lieted some normal sounds with explanations.
• Buzzing - heard when the weter valve opens to fill the ice
maker
• Pulsating - fans/compressor adjusting to optimize
performance
• Hissing/Rattling - flow of refrigerant, movement of water
lines, or from items placed on top of the refrigerator
• Sizzling/Gurgling - water dripping on the heater during
defrost cycle
• Popping - contraction/expansion of inside walls, especially
during initial cooPdown
• Watar running - may be heard when weter melts during the
defrost cycle and runs into the drain pan
• Creaking/Cracking - occurs as ice is being ejected from the
ice maker mold.
15
The doors will not close completely
• Door blocked open? Move food packages away from door.
• Bin or shelf in the way? Push bin or shelf back in the correct
position.
The doors are difficult to open
• Gaskets dirty or sticky? Clean gaskets and contact surfaces
with mild soap and warm water. Rinse and dry with soft cloth.
• Large amount of ice recently removed? Allow 24 hours for
ice maker to produce more ice.
• Ice cube jammed in the ice maker ejector arm?
Remove ice from the ejector arm with a plastic utensil.
• Water filter installed on the refrigerator? Remove filter and
operate ice maker. If ice volume improves, then the filter may
be clogged or incorrectly installed. Replace tiger or _install g
correctly.
• Reverse osmosis water filtration system connected to
your cold water supply? This can decrease water p_ssure.
See "Water Supply Requirements."
The ice cubes are hollow or small
Temperatare is too warm
• New installation? Allow 24 hours following installation for the
refrigerator to cool completely.
• Door(ej opened oftan or left open? Allews warm air to entsr
refrigerator. Minimize door openings and keep doors fully
closed.
• Large load of food added? Allow several hours for
refrigerator to return to normal temperature.
• Controls set correctly for the surrounding conditions?
Adjust the controls a setting colder. Check temperature in
24 hours. See "Using the Controls."
There is interior moisture buildup
NOTE: Some moisture build-up is normal.
• Humid room? Contributes Io moisture build-up.
• Door(ej opened often or left open? Allows humid air Io enter
refrigerator. Minimize door openings and keep doors fully
closed.
The ice maker is not producing ice or not enough ice
• Refrigerator connected to a water supply and the supply
shutoff valve turned on? Connect refrigerator to water
supply and turn water shutoff valve fully open.
• Kink in the water source line? A kink in the line can reduce
water flow. Straighten the water source line.
• Ice maker turned on? Make sure wire shutoff arm or switch
(depending on model) is in the ON position.
• New installation? Wait 24 hours after ice maker installation
for ice production to begin. Wait 72 hours for full ice
production.
• Freezer door closed completely? Firmly close the freezer
compartment door. If the freezer compartment door will not
close all the way, see "The doors will not close completely."
NOTE: This is an indication of low water pressure.
• Water shutoff valve not fully open? Turn the water shutoff
valve fully open.
• Kink in the water source line? A kink in the line can reduce
water flow. Straighten the water source line.
• Water filter installed on the refrigerator? Remove filter and
operate ice maker. If ice quality improves, then the filter may
be clogged or incorrectly installed. Replace filter or reinstall it
correctly.
• Reverse osmosis water filtration system connected to
your cold water supply? This can decrease water pressure.
See "Water Supply Requirements."
• Questions remain regarding water pressure? Call a
licensed, qualified plumber.
Off-taste, odor or gray color in the ice
• New plumbing connections? New plumbing connections
can cause discolored or of f-flevored ice.
• Ice stored too long? Discard ice. Wash ice bin. Allow
24 hours for ice maker to make new ice.
• Odor transfer from food? Use airtight, moisture proof
packaging to store food.
• Are there minerals (such as sulfur) in the water? A water
filter may need to be installed to remove the minerals.
• Water filter installed on the refrigerator? Gray or dark
discoloration in ice indicates that the water filtration system
needs addglenal flushing. Flush the water system before using
a new water filts_ Replace water filter when indicated. See
"Water Filtration System."
16
The water dispenser will not operate propedy
• Refrigerator connected to a water supply and the supply
shutoff valve turned on? Connect refrigerator to water
supply and turn water shutoff valve fully open.
• Kink in the water source line? Straighten the water source
line.
• New installation? Flush and fill the water system. See "Water
Dispense_"
• Is the water pressure at least 30 psi? The water pressure to
the home determines the flow from the dispense_ See "Water
Supply Requirements."
• Water filter installed on the refrigerator? Remove filter and
operate dispense_ If water flow increases, the filter may be
clogged or incorrectly installed. Replace filter or reinstall it
correcg_
• Refrigerator door closed completely? Close the door firmly.
If it does nat close completely, see "The doors will not close
completely"
• Recently removed or reversed the doors? Make sure the
water dispenser wire/tube assembly has been properly
reconnected at the bottom of the refrigerator doo_ See
"Refrigerator Doors."
• Reverse osmosis water filtration system connected to
your cold water supply? This can decrease water pressure.
See "Water Supply Requirements."
Water is leaking from the dispenser system
WATERFILTERCERTIFICATIONS
S_ ofc_im_ma
Water TIea(me_z[ Deice
Cer_if:cate Number
04-1612
NOTE: One or two drops of water after dispensing is normal.
• Glass not being held under the dispenser long enough?
Hold the glass under the dispenser 2 to 3 seconds after
releasing the dispenser lever.
• New installation? Flush the water system. See 'MTater
Dispenser."
• Recently changed water filter? Flush the water system. See
"Water Dispenser."
• Water on the floor near the base grille? Make sure the
water dispenser tube connections, at the bottom of the
refrigerator door, are fully tightened. See "Refrigerator
Doors."
Water from the dispenser is warm
NOTE: Water from the dispenser is only chilled to 50°F (10°O).
• New installation? Allow 24 hours after installation for the
water supply to cool completely.
• Recently dispensed large amount of water? Allow 24 hours
for water supply to cool completely.
• Water not been recently dispensed? The first glass of water
may not be cool. Discard the first glass of water.
• Refrigerator connected to a cold water pipe? Make sure
the refrigerator is connected to a cold water pipe. See "Water
Supply Requirements."
D__lam_ nt of H_ahh _pdces
Water Tl_-a tmere Device
Certificate N_muber
04-/61/
17
PRODUCTDATASHEETS
Base Grille Water Filtration System
Model WF-L200V Capacity 200 Gallons (757 Liters)
Model WF-NL120V Capacity 120 Gallons (454 Liters)
System tested and certified by NSF International agah_st NSF/ANSI
p=dichlorobenzene, O=Dichlo_obenzene, Toxaphene, Ethyl Benzene,
Standard 53 fo_ the reduction of Lead, Mercury, Benzene,
1,2,4=t_ichlorobenzene and against NSF/ANSI Standard 42 for the
reduction of Chlorine Taste and Odor and Particulate Class HL
This system has been tes_d according to ANSVNSF 42/53 for the reduction of the substances listed below. The concentration of the
indicted substances in water entering the system was reduced to a o3ncentration less than or equal to the permissible limit for water
leaving the system, as specified in ANSI/NSF 42/53.
Substance Reduction NSF Reduction Average Influent Challenge Maximum Average Minimum % Average %
Aesthetic Effects Requirements Influent Concentration Effluent Effluent Reduction Reduction
ChlorineTaste/Ode[ _50% 1.9 mg/L 0.06 mg/L >75% >75%
Ioo 'co'a'eO'ass'"I 14033 / ,L 1 '2/m 198.7 IgP.0
Contaminant NSF Reduction Average Influent Challenge Maximum Average Minimum % Average %
Reduction Requirements Influent Concentration Effluent Effluent Reduction Reduction
Lead:@pH6.5 0.01mg/L 0.14 mg/LT 0.15 mg/L _ 10% 0.0014 mg/L 0.0011 mg/L 99.00% 99.21%
Lead: @pH 8.5 0.01mg/L 0.15 mg/L t 0.15 mg/L ± 10% 0.0069 mg/L 0.0042 mg/L 95.40%% 97.20%
Mercury: @pH 6.5 0.002 mg/L 0.0059 mg/L 0.006 mg/L _ 10% 0.0009 mg/L 0.0004 mg/L 84.74% 93.22%
Mercury: @pH 8.5 0.002 mg/L 0.0054 mg/L 0.006 mg/L _ 10% 0.0007rag/L 0.00043 mg/L 87.03% 92.03%
Benzene 0.005 mg/L 0.0157 mg/L 0.015 mg/L _ 10% 0.002 mg/L 0.00083 mg/L 87.26% 94.71%
3 dichlorobenzene 0.075 mg/L 0.210 mg/L 0.225 mg/L _ 10% 0.0005 mg/L 0.0005 mg/L 99.76% 99.76%
O Dichlorobenzene 0.60 1.84 1.8 ± 10% 0.20 0.0418 89.13 97.73
Toxaphene 0.003 0.0143 0.015 ± 10% 0.0012 0.0010 91.60 93.00
Ethyl Benzene 0.70 2.00 2.1 ± 10% 0.40 0.085 80.00 95.75
1,2,4 trichlorobenzene 0.07 0.232 0.21 ± 10% 0.0041 0.0016 98.23 99.31
Test Parameters: pH = 7.5 ± 0.5 unless otherwise noted. Flow = 0.5 gpm (1.9 Lpm). Pressure = 60 psig (413.7 kPa). Temp. = 63°F
(17.2°0).
• It is essentialthat operational, maintenance, and filter
replacement requirements be carried out for the product to
perform as advertised.
• Model WF-L200V: The filter monitor system measures the
• Refer to the front cover or "Accessories" section for the
Manufacturer's name, address and telephone number.
• Refer to the "Warranty" section for the Manufacturer's limited
warranty.
amount of water that passes through the tiger and alerts you
to replace the filter. When 90% of the filter's rated Ige is used,
Application Guidelines/Water Supply Parameters
the filter indicator light changes from green 1oyellow. When
100% of the filter's rated life is used, the filter indicator light
changes from yellow to red, and it is recommended that you
replace the tiger. Use replacement cartridge L20OV/NL120V,
part #4396701. 2004 suggested retail price of $32.99 U.S.A./
$49.99 Canada. Prices are subject to change without notice.
Water Supply City or Well
Water Pressure 30 - 120 psi (207 - 827 kPa)
Water Temperature 33 ° - 100°F (0.6 ° - 37.8°C)
Service Flow Rate 0.5 GPM (1.9 Wmin.) @ 60 psi.
Model WF-NLf20V: Change the water filter cartridge every 6-
9 months. Use replacement cartridge L200V / NL12OV, part
#4396701. 2004 suggested retail price of $32.99 U.S.A./
$49.99 Canada. Prices are subject to change without notice.
• The product is for cold water use only.
• Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after
the system.
*Class Ill par[iole size: > 5 to < 15 um
*_Test requirement is at least 100,00O par ticles/m L of AC Fine Test Dust.
I_h ese contaminators are not necessarily in your water suppl_ Performance may vary based on Ioc_ water conditions,
® NSF is a registered trademark of NSF Internation_.
18
Loading...