Whirlpool GI1500XHW1, GI1500XHW0 Owner’s Manual

Appliances

ICE MAKER

tc_ £_,,'_

For questions about features, operation/performance,

parts, accessories or service, call: 1-800-253-1301.

In Canada, call for assistance 1-800-461-5681, for installation

and service, call: 1-800-807-6277 or visit our website at...

www.whirlpool.com or www.whirlpool.com/canada

LAMACHINEA

GLA(_ONS

Au Canada, pour assistance, composer le 1-800-461-5681, pour

installation ou service 1-800-807-6777 ou visitez notre site web

Table of Contents/Table des matieres .............................. 2

www.whirlpool.com/canada

2208357

TABLEOF

TABLEDES

CONTENTS

ICE MAKER SAFETY ....................................................... 3

PARTS AND FEATURES .................................................. 4

INSTALLING YOUR ICE MAKER ....................................... 5

Unpacking the Ice Maker ................................................. 5

Space Requirements ....................................................... 5

Electrical Requirements ................................................... 6

Leveling the Ice Maker ..................................................... 6

Connecting the Ice Maker to a Water Source ................ 7

Reversing the Door Swing ............................................... 9

Understanding Sounds You May Hear ......................... 11

USING YOUR ICE MAKER ............................................... 11

Understanding How Your Ice Maker Works ................. 11

Setting the Controls ....................................................... 12

CARING FOR YOUR ICE MAKER ................................... 12

Cleaning Exterior Surfaces ............................................ 12

Cleaning the Ice Maker System .................................... 13

Cleaning the Condenser ................................................ 13

Cleaning the Interior Components ................................ 14

Vacation and Moving Care ............................................ 15

TROUBLESHOOTING ....................................................... 16

ASSISTANCE OR SERVICE ............................................. 17

WARRANTY ...................................................................... 18

MATIERES

SECURITE DE LA MACHINE A GLA(;ONS ................... 19

PIECES ET CARACTERISTIQUES ................................. 20

INSTALLATION DE LA MACHINE A GLA(;ONS ............ 21

Deballage de la machine a glaqons .............................. 21

Espace requis ................................................................. 21

Specifications electriques ............................................. 22

Mise d'aplomb de la machine a glaqons ...................... 22

Raccordement de la machine

glaqons a I'alimentation en eau ................................ 23

Inversion du sens d'ouverture de la porte .................. 26

Comprehension des bruits

que vous pouvez entendre ............................................ 27

UTILISATION DE LA MACHINE A GLA(;ONS ................ 28

Comprehension du fonctionnement

de la machine a glaqons ............................................... 28

Reglage des commandes .............................................. 29

ENTRETIEN DE LA MACHINE A GLA(;ONS .................. 29

Nettoyage des surfaces exterieures ............................. 29

Nettoyage du systeme de la machine a glaqons ......... 30

Nettoyage du condenseur ............................................. 30

Nettoyage des composants interieurs ......................... 31

Precautions a prendre pour les

vacances ou le demenagement .................................... 32

DEPANNAGE ..................................................................... 33

ASSISTANCE OU SERVICE ............................................. 34

GARANTIE ......................................................................... 35

ICE MAKERSAFETY

Your safety and the safety of others is very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This symbol alerts you to hazards that can kill or hurt you and others. All safety messages will be preceded by the safety alert symbol and the word "DANGER" or

This is the safety alert symbol. "WARNING." These words mean:

You will be killed or seriously injured if you don't follow instructions.

You can be killed or seriously injured if you don't

follow instructions.

All safety messages will identify the hazard, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

_VARNNNG: To reduce the risk of fire, electric shock, or injury when using your ice maker, follow these basic precautions:

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

• Disconnect power before cleaning.

• Disconnect power before servicing.

• Replace all panels before operating.

• Use two or more people to move and install ice maker.

SAVE THESE INSTRUCTIONS

PARTSANDFEATURES

CLEANING

1. Control Panel

2. Cutter Grid Cover

3. Water Pan

4. Model Serial Number Label (on left cabinet wall)

5. Ice Retainer Baffle

6. Lower Access Panel

7. Ice Level Sensor

8. Magnetic Door Catch

INSTALLINGYOUR

ICEMAKER

Excessive Weight Hazard

Use two or more people to move and install ice maker.

Failure to do so can result in back or other injury.

Removing packaging materials

IMPORTANT: Do not remove any permanent instruction

labels inside your ice maker or the Tech Sheet that is fastened behind the lower access panel.

• Remove tape and any labels from your ice maker before using (except the model and serial number

label).

To ensure proper ventilation for your ice maker, the front side must be completely unobstructed. The unit may be closed-in on the top and three sides, but the installation should allow the ice maker to be pulled forward for servicing if necessary.

Installation of the ice maker requires a cold water supply inlet of V4"(6.35 mm) OD soft copper tubing with a shut-off valve and either a gravity-drain system or condensate pump to carry the water to an existing

drain. Choose a well ventilated area with temperatures above

55°F (13°C) and below IO0°F (38°C). Best results are obtained between 70°F (21°C) and 90°F (32°C). This

unit MUST be installed in an area protected from the elements, such as wind, rain, water spray, or drip.

When installing the ice maker under a counter, follow the recommended opening dimensions shown. Place electrical and plumbing fixtures in the recommended

location as shown. NOTE: Do not kink or pinch the power supply cord

between the ice maker and cabinet.

To remove any remaining tape or glue, rub the area briskly with your thumb. Tape or glue residue can also be easily removed by rubbing a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry.

Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your ice maker.

Cleaning before use

After you remove all of the packaging materials, clean the inside of your ice maker before using it. See the cleaning instructions in the "Caring for Your Ice Maker" section.

34"

(86.4 cm)

Min.

341/2,,

(87.6 cm)

Max.

1.Recommended Location for Electrical and Plumbing Fixtures.

2. Floor Level

You should choose a location where the floor is even. It is important for the ice maker to be level in order to

work properly. If needed, you can adjust the height of the ice maker by changing the position of the rear wheels. See the "Leveling the Ice Maker" section.

t 281/2.

(72.4 cm)

24"

30.1 cm)

(38.1 cm)

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in

death, fire, or electrical shock.

Before you move your ice maker into its final location, it is important to make sure you have the proper electrical

connection: A 115 Volt, 60 Hz., AC only 15 ampere electrical supply,

properly grounded in accordance with the National Electrical Code and local codes and ordinances, is

required. It is recommended that a separate circuit, serving only

your ice maker, be provided. Use a receptacle which cannot be turned off by a switch or pull chain.

Recommended grounding method

For your personal safety, this appliance must be grounded. This appliance is equipped with a power supply cord having a 3 prong grounding plug. To minimize possible shock hazard, the cord must be plugged into a mating, 3 prong, grounding-type wall receptacle, grounded in

accordance with the National Electrical Code and local codes and ordinances. If a mating wall receptacle is not

available, it is the personal responsibility of the customer to have a properly grounded, 3 prong wall receptacle installed by a qualified electrician.

It is important for the ice maker to be level in order to work properly. Depending upon where you install the ice maker, you may need to make several adjustments to level it.

Tools required

• Carpenter's level

• Adjustable wrench

• 1/4"socket wrench

Undercounter installation

If you are installing the ice maker under acountertop, then you may need to adjust the height of the ice maker. The adjustable rear wheels are preset to position 1 for a cabinet opening height of 34" (86.4 cm).

1.For cutout height of 34" (86.4 cm)

2. For cutout height of 34_" (86.7 cm)

3. For cutout height of 34_6" (87.2 cm)

4. For cutout height of 34½" (87.6 cm)

adjust the rear wheel height

Using a 1/4"socket wrench, remove the five screws from

the rear access panel and carefully pull the panel away from the drain hose.

Using a%" or adjustable wrench, remove the screw

that holds the rear wheel. NOTE: Pushing up against the top back of the ice

maker takes some of the weight off of the wheels. This makes it easier to remove the screws.

Move the rear wheel and screw to a new position as needed for your cabinet opening height. Tighten the screw completely.

Repeat Steps 2 and 3 to change the position of the

wheel on the other side.

Replace the rear panel and screws. Be sure that the

drain tube is positioned in the opening provided.

Use the front leveling legs to make sure the product is

level.

To adjust the front leveling legs Your ice maker has two adjustable leveling legs to help you

steady the product and make sure it is level. SUGGESTION: It is easier to adjust the leveling legs if you

have another person to assist you. 1, Place a carpenter's level on top of the product to see if

the ice maker is level from front to back and side to side.

Push up on the top front of the ice maker, and then locate the leveling screws that are on the bottom front of the product.

Using an adjustable wrench, change the height of the legs as follows:

• Turn the leveling leg to the right to lower that side of

the ice maker.

• Turn the leveling leg to the left to raise that side of

the ice maker.

NOTE: The ice maker should not wobble. Use shims to add stability when needed.

Read all directions carefully before you begin.

IMPORTANT:

• All installations must be in accordance with local plumbing codes requirements,

• Use copper tubing and check for leaks,

• Install copper tubing only in areas where temperatures will remain above freezing,

Tools required:

• Standard screwdriver

• 7A6"and 1/2"open-end wrenches or two adjustable wrenches

• 1/4" nut driver

• 1/4"drill bit

• Hand drill or electric drill properly grounded

NOTE: Your ice maker dealer has a kit available with a 1/4" (.635 cm) saddle-type shut-off valve, a union, and copper

tubing. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes. Do not use a piercing-type or ¾6" (.476 cm) saddle valve which reduces water flow and clogs more easily.

Use a carpenter's level to re-check the ice maker to see

that it is even from front to back and side to side. If the ice maker is not level, repeat Steps 2 and 3. If the ice

maker is level, go to the "Connecting the Ice Maker to a Water Source" section.

Freestanding installation

If you are not installing your ice maker under a countertop, you will probably not need to adjust the rear wheel height, Follow the steps outlined in "To adjust the front leveling legs" earlier in this section,

NOTE: The ice maker should not wobble. Use shims to add stability when needed.

Connecting the water line:

1. Turn off main water supply. Turn on nearest faucet long

enough to clear line of water.

Find a 1/2"(1.27 cm) to 11/4"(3.18 cm) vertical cold

water pipe near the ice maker. NOTE: Horizontal pipe will work, but the following

procedure must be followed: Drill on the top side of the pipe, not the bottom. This will help keep water away from the drill. This also keeps normal sediment from collecting in the valve.

Using a grounded drill, drill a 1/4"(.635 cm) hole in the

cold water pipe you have selected.

Fasten shut-off valve to cold water pipe with pipe clamp. Be sure outlet end is solidly in the 1/4"(.635 cm) drilled hole in the water pipe and that washer is under the pipe clamp. Tighten packing nut. Tighten the pipe clamp screws carefully and evenly so washer makes a watertight seal. Do not overtighten the pipe clamp or you may crush cold water pipe if it is soft copper tubing. Do not use a piercing-type or ¾6" (.476 cm) saddle-type valve which reduces water flow and clogs more easily.

5. REAR VIEW

Now you are ready to connect the copper tubing. Use 1/4"(.635 cm) OD soft copper tubing for the cold water supply.

Measure from the connection at the front of the ice

II I

maker to the cold water pipe. Add 3 feet to ensure that you have the proper length. This is the length of 1/4"(.635 cm) OD soft copper tubing you need for the job. Be sure both ends of the copper tubing are

cut square. Slip compression sleeve and compression nut on

copper tubing as shown. Insert end of tubing into outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten.

1. Upper Water Line Access Hole

2. Lower Water Line Access Hole

9, Bend the copper tubing to meet the water valve inlet on

the water valve which is located in the front of the ice maker cabinet as shown.

10.

Unscrew the water valve inlet cover, and attach the

copper tubing with the compression sleeve and nut.

6 5 4

1. Cold Water Pipe

2. Pipe Clamp

3. Copper Tubing

4. Compression Nut

5. Compression Sleeve

6. Shut-Off Valve

7. Packing Nut

NOTE: To prevent rattling, be sure the copper tubing does not touch the cabinet's side wall or other parts

inside the cabinet.

FRONT VIEW

I I

Place the free end of the tubing into a container or sink, and turn on main water supply and flush out tubing

until water is clear. Turn off shut-off valve on the water pipe.

NOTE: Always drain the water line before making the final connection to the inlet of the water valve to

prevent possible water valve malfunction.

Remove the two screws in the lower access panel and the two screws in the base grille area of the front panel support. Pull forward to remove the lower access panel.

Position the tubing so it can enter one of the two access holes located at the right-hand rear of the cabinet as shown. The tubing should extend beyond the cabinet front when the cabinet is pushed back into position. Move the ice maker into position.

511/16"

(14.5crn)

1. Water Pan Drain

2. Water Valve

11,

Turn shut-off valve on. Check for leaks. Tighten any connections (including connections at the valve) or nuts that leak. The ice maker is equipped with a built-in water strainer. If local water conditions require periodic cleaning or a well is your source of water supply, a

second water strainer should be installed. Obtain a water strainer from your nearest appliance dealer and

install it at either tube connection.

12, Replace the lower access panel and screws.

Connecting the drain

Gravity drain system

Connect the drain pump hose (provided with the product) to your drain in accordance with all state and local codes and ordinances. If the ice maker is provided with a gravity drain system, follow these guidelines when installing drain lines: (This will prevent water from flowing back into the ice maker storage bin and potentially flowing onto the floor causing water damage.)

• Drain lines must have a minimum of%" (1.6 cm) inside diameter.

Drain lines must have a 1" drop per 48" [(2.54 cm) drop

per 122 cm)] of run or 1/4"drop per 12" [(.635 cm) per

30.5 cm)] and must not have low points where water can settle.

The floor drains must be large enough to accommodate drainage from all drains.

The ideal installation has a standpipe with a 11/2"(3.81 cm) to 2" (5.08 cm) PVC drain reducer installed directly

below the outlet of the drain tube as shown. You must maintain a 1" (2.54 cm) air gap between the drain pump

hose and the standpipe. It may be desirable to insulate the drain line thoroughly

up to the drain inlet.

After ensuring that the drain system is adequate, follow these steps to properly place the ice maker:

1, Plug in ice maker or reconnect power. 2, Re-check the ice maker to be sure that it is level. See

the "Leveling the Ice Maker" section.

3. Push the ice maker into position so that the ice maker drain tube is positioned over the PVC drain reducer.

SIDE VIEW

If it is required by your local sanitation code, seal the cabinet to the floor with an approved caulking compound after all water and electrical connections

have been made,

Drain pump system (on some models) Connect the drain pump hose (provided with the product)

to your drain in accordance with all state and local codes and ordinances.

<t.I I,R,

TOOLS NEEDED: sad' wrench, 1/4"wrench, flat putty knife,

Phillips screwdriver

Hinge Pin

5A6-inchHex Head HingeScrew

Handle Screw

Endcap Screw

To remove door from hinges:

l,.u

3 5/811 (9,2 cm)

I I

23"

(58,4cm)

2" - 1 1/2"

(5cm - 3,8 cm)

1. Drain Hose

2. 1" (2.54 cm) Air Gap

3. PVC Drain Reducer

4. Center of drain should be 23" (58.4 cm) from front of door (with or without the ¾"

(1.91 cm) panel on the door).

Electrical Shock Hazard

3 4

Disconnect power before servicing.

Replace all panels before operating.

Failure to do so can result in death or

electrical shock.

1, Unplug ice maker or disconnect power. 2, Remove the handle screws and handle (on some

models). Keep the parts together and set them aside.

Remove the two hex head screws from the upper

access panel. Lift up on the bottom of the access panel to release it from the front of the ice maker. Do not disconnect the wires.

With the upper access panel raised, remove the hinge pin from the top hinge.

Remove the door from the hinges and screw the top

hinge pin back into the top hinge.

Replace the upper access panel loosely on the ice

maker.

Reverse the door endcaps as follows:

• Remove both the screws and endcaps (top and bottom).

• Place the top endcap on the bottom of the opposite side of the door with the long flat side facing the

door front.

replace door on hinges:

Place plastic hinge pin sleeve in the top hinge hole on the door. Align the door with the top hinge hole and replace the top hinge pin.

Replace the upper access panel and secure it with the hex head screws.

3, Replace the handle and handle screws.

Top Hinge

1.Hinge Pin

2. Hinge Pin Sleeve

3. Hinge

4. Hex Head Hinge Screw

Bottom Hinge

• Place the bottom endcap on the top of the opposite side of the door with the long flat side facing the

door front.

8. Set the door aside.

To reverse the hinges: 1, Unscrew and remove the top hinge. Replace the

screws in the empty hinge holes.

Remove the screws from the bottom of the opposite side of the ice maker cabinet. Turn the top hinge upside down so that the hinge pin points up. Place the hinge on the bottom opposite side of the ice maker and tighten screws.

Remove the plastic hinge pin sleeve from the "old" bottom hinge and replace it on the new bottom hinge pin.

4, Remove the "old" bottom hinge screws and hinge.

Replace the screws in the empty hinge holes.

5, Remove the screws from the top of the opposite side of

the ice maker cabinet. Turn the hinge upside down so that the hinge pin points down.

6, Raise the upper access panel and place the hinge on

the top opposite side of the ice maker. Tighten the hinge screws.

7. Remove the top hinge pin

1.Hex Head Hinge Screw

2. Hinge Pin Sleeve

3. Hinge

4. Hinge Pin

reverse the door catch:

Remove the hole plugs from the opposite side of the

door and set aside.

Remove the screws from the magnetic door catch and

replace it on the opposite side of the door.

Push the hole plugs into place on the opposite side of

the door.

4. Plug in ice maker or reconnect power,

USINGYOUR

Your new ice maker may make sounds that are not familiar to you. Because the sounds are new to you, you might be

concerned about them. Most of the new sounds are normal. Hard surfaces like the floor, walls and cabinets can make the sounds seem louder than they actually are. The

following describes the kinds of sounds that might be new to you and what may be making them.

• You will hear a buzzing sound when the water valve opens to fill the water reservoir for each cycle.

• Rattling noises may come from the flow of the refrigerant or the water line. Items stored on top of the

ice maker can also make noises. The high efficiency compressor may make a pulsating

or high pitched sound. Water running over the evaporator plate may make a

splashing sound.

Water running from the evaporator plate to the water reservoir may make a splashing sound.

As each cycle ends, you may hear a gurgling sound due to the refrigerant flowing in your ice maker.

You may hear air being forced over the condenser by the condenser fan.

During the harvest cycle, you may hear a "thud" when the ice sheet slides from the evaporator onto the cutter grid.

When you first start the ice maker, you may hear water running continuously. The ice maker is programmed to run a rinse cycle before it begins to make ice.

ICEMAKER

When you first start your ice maker, the water pan will fill and the system will rinse itself before starting to make ice. The rinsing process takes about five minutes.

Under normal operating conditions, the ice maker will cycle at preset temperatures. The ice level sensor located in the ice storage bin will monitor the ice levels.

IMPORTANT

• If the water supply to the ice maker is turned off, be

sure to set the ice maker control to OFE The ice maker is designed to make clear ice from the

majority of water sources on a daily basis. Ifyour results are unsatisfactory, your water may need to be

filtered or treated.

Making Ice

Water is constantly circulated over a freezing plate. As the water freezes into ice, the minerals in the water are

rejected. This produces a clear sheet of ice with a low mineral content.

When the desired thickness is reached, the ice sheet is released and slides onto a cutter grid. The grid divides

the sheet into individual cubes.

+ 25 hidden pages