Whirlpool GCIP 6848/1 IN BK, AZB 9570, GCFP 4824/1 WH INSTRUCTION FOR USE
QUICK REFERENCE GUIDE
QU--
GB
Program Selection and Operating Your Machine
4 3 2
1765
1. On / Off Button
2. Start/Pause/Cancel Button
3. Display
4. Program Selection Button
5. Half Load Button
6. Delayed Start Button
7. Handle
8. Program Indicator
9. Salt Indicator
10. Rinse Aid Indicator
11. Remaining Time Indicator/Delay
Time Indicator
12. Start Indicator
13. Delayed Start Indicator
14. Half Load “ ” Indicator
15. Program Steps Follow-up Indicator
a Washing Step Indicator “ ”
b Drying Step Indicator “ ”
c End of Program Indicator “ ”
Button and Button Descriptions
On / Off Button (1)
When you press the On/Off button, the display switches on with the last
program used and it dims when you turn the machine off.
If the Half Load (5), function are enabled during the last program used, these
functions will remain active when the machine is turned off and on again. If you
would like to disable these functions after turning the machine off and on again,
you must press the relevant buttons.
Start / Pause / Cancel Button (2)
It is used to start, pause or cancel the selected program or the delayed start
countdown. The selected program will start running when the Start / Pause /
Cancel button (2) is pressed. When the button is pressed, (12) lights up.
Wait for two seconds to view the full display on the screen after you turn on
the machine by pressing the On/Off button (1) before you press Start / Pause /
Cancel (2) button.
Program Selection Button (4)
You can select the washing program you want to use with the aid of the
“Program Data and Table of Average Consumption Values” after pressing
the program selection button. Number of the selected program appears
in the program indicator (8) on the display (3) in the format of
....... Program number will increase by one each time you press the program
selection button. Number of the dened programs can change depending on
the model you have purchased.
Half Load Button (5)
If you want to run your machine without loading it completely, place your dishes
into the machine as you desire. First, press the On / Off Button (1). Select the
desired program and press the Half Load (5) button. You must see the Half
Load indicator (14) appearing on the screen. Start the program by pressing
the Start / Pause / Cancel button (2). Thanks to the Half Load option, you can
use both lower and upper baskets of your machine and you can save water
and energy.
Delayed Start Button (6)
You can delay the start of the selected program until 9 hours with increments of
1 hour by means of the Delayed Start Function.
Program Selection
You can select the desired program after turning on the machine by pressing
the On / Off button (1). Switch to the program you want to operate by pressing
program selection button (4). You can follow up the program you are in from
the program indicator (8) on the screen. Program number will increase by one
each time you press the program selection button (Number of the dened
programs can change depending on the model you have purchased). The
selected washing program will start running when the Start / Pause / Cancel
button (2) is pressed symbol (12) light up. Time indicator (11) will start
displaying the estimated remaining time to the end of program.
Total time can be different from the time indicated at the beginning
since it can change while the program is running, depending on the
temperature of the room where your machine is installed, temperature
of the supply water, auto-cleaning of the water softening system
(regeneration) and amount of the dishes.
Adding Functions to the Program
With the help of the add function buttons, you can run the selected program
together with the Half Load (5) and Delayed Start (6) functions.
To add a function to the program:
1. Select the program by pressing program selection button (4).
2. Press the button of the function that you want to enable and check to
see a indicator for the relevant function on the display.
3. You can start the program by pressing the Start / Pause / Cancel button
(2).
Program Steps Follow-up
You can follow up the step while current program is running from the Program
Steps follow up indicator (15)
a Washing Step Indicator (15 a)
b Drying Step Indicator (15 b)
c End of Program Indicator (15 c)
The display shows the steps for washing 15 a and drying 15 b, respectively,
while the selected program is running. Only the End of Program indicator 15
c lights up when the program is over. Remaining Time Indicator (3) displays
“0:00”.
Canceling a Program
Press Start / Pause / Cancel button (2) for three seconds to cancel a program
that is already running. Release the button when symbol (12) start ashing
in the display. For a couple of minutes the machine will fulll the necessary
operations required for cancellation. Remaining time indicator (11) displays
“0:00”. You may select and operate a new program following the program
cancellation process. There might be residues of detergent or rinse aid left in
the machine and/or on the pieces being washed depending on the step the
previous program was in at the time of such cancellation.
Changing a Program
If you want to change running program, rst of all press Start / Pause / Cancel
button (2) to switch your machine into pause mode. Second, switch to the
desired program by pressing Program Selection button (4). Third, Start the
new program by pressing Start / Pause / Cancel button (2) again. Your new
selection will resume operation from the step in the previous program (For
example, if the previous program was in rinsing step, the new one will also
start from the rinsing step). If you want to run the newly selected program
from the beginning, you have to apply the program cancellation process rst
and then select a new program.
Programming the Delayed Start
You can delay the start of the selected program until 9 hours. Delayed start
can not be set after the program starts. The selected program must not be
started in order to be able to set the delay time.
Delayed start indicator sand glass (13) will start ashing when the delayed
start button (6) is pressed. You can set the desired time by pressing the
delayed start button (6). Press the Start / Pause / Cancel button (2) after
setting the time. The delayed start indicator sand glass (13) and play icon
(12) will remain lit on the display during the delayed start countdown and the
delay time indicator (11) will display the remaining time. Program will start
automatically when the countdown is over.
You can use the delayed start function if you are utilizing the economic
electricity tariff.
If you want to change the program or functions while the delayed start
function is enabled, then pause the machine by pressing the Start / Pause /
Cancel button (2). You will see that the countdown stops. The delayed start
indicator will start ashing. Select the new program and/or add the functions
as described in Program Selection and Table of Average Consumption
Values. Resume the delayed start countdown by pressing the Start / Pause /
Cancel button (2).
If you want to cancel delayed start countdown while it is in progress, then
press the Start / Pause / Cancel button (2) for three seconds. Release
the button when symbols (12) start ashing in the display. For a couple
of minutes the machine will fulll the necessary operations required for
cancellation. Remaining time indicator (11) displays “0:00”. You may
select and operate a new program following the delayed start countdown
cancellation process.
If you want to select a new delayed start time while the delayed start
countdown is in progress, then pause the machine by pressing the Start /
QUICK REFERENCE GUIDE
GB
Pause / Cancel button (2). Set the desired time by pressing the Delayed Start
Button (6). Start the countdown for the new time by pressing the Start / Pause
/ Cancel button (2) again.
Salt Indicator
Please check the salt indicator (9) on the display to see whether there is
enough softening salt in your machine or not. You need to rell the powder
dispenser whenever the salt warning indicator light lights.
WARNING:
If the water hardness level is stored as (r1), salt indicator will never come
on even if the salt container is empty. (Adjusting the water hardness level is
explained in Water Softening System section.)
Rinse Aid Indicator
Check the rinse aid warning display (10) on the screen to nd out if there is
sufcient amount of rinse aid in your machine. You must rell the rinse aid
container when the rinse aid indicator comes on.
WARNING:
If the Rinse Aid Indicator is set to (OFF), rinse aid indicator will never come on
even if the rinse aid container is empty.
Rinse Aid Indicator Setting
• When your machine is switched off, press Half Load button (5) and
then On / Off button (1) to switch it on.
• Hold Half Load button (5) pressed and release On / Off button (1).
• Keep Half Load button (5) pressed for three seconds more.
• Rinse Aid Indicator (10) comes on and the stored rinse aid indicator
status of your machine appears on the display in the format of “ON” or
“OFF”.
• You can change the status of the indicator as “ON” or “OFF” with Start
/ Pause / Cancel button (2). If you switch off the machine with “On/Off”
button (1) when the status is “ON”, then the rinse aid indicator will come
on when the rinse aid level in your machine becomes low while the
machine is in use. If you switch off the machine with “On/Off” button (1)
when the status is “OFF”, then the rinse aid indicator will never come on.
Starting Your Machine
• Plug the mains plug into the wall socket.
• Open the tap.
• Open the door.
• Place the dishes.
• Check if the upper and lower impellers rotate freely.
• Put sufcient amount of detergent in the detergent dispenser and close
its lid.
• Press On/Off button.
• Check if the salt and rinse aid warning indicators (9,10) light and add salt
and/or rinse aid if needed.
• Determine your washing program with the aid of the Program Data and
Table of Average Consumption Values.
• You can select the determined washing program by pressing program
selection button (4).
• You can see the program time in the Remaining Time Indicator (11).
• If necessary, you can change your washing program as you prefer by
means of the Add Function Buttons (6, 5).
• Start the program by pressing the Start / Pause / Cancel button (2).
WARNING:
Pay attention not to open the door of the machine when it is running. Stop
the machine by pressing Start / Pause / Cancel button (2) if you have to open
the door. Then, open the door of your machine. There may be a rush of vapor
when you open the door of your machine; be careful. Close the door and
press Start/Pause/Cancel button (2) again. Program will resume running.
• End of Program indicator (15 c) will light up.
• Turn off your machine by pressing On / Off button (1).
• Close the tap.
• Unplug the mains plug from the wall socket.
• Leave your dishes in the machine for about 15 minutes after they are
washed in order to have them cooled down. Your dishes will dry in a
shorter time if you leave the door of your machine ajar during this period.
This will increase the drying effectiveness of your machine.
Programme Table
Programme number
Programme name
Cleaning temperature
Degree of Soiling Suitable for
Detergents
A=25 cm³/15 cm³ B=5 cm³
Programme sequence
(without options)
Duration (min)
Water (I)
Energy (kWh)
The consumption values shown in the table were determined under standard conditions. Differences may therefore occur under practical conditions.
* Reference programme for testing institutes The tests in accordance with EN 50242 must be carried out with a full water softener salt dispenser and a full rinse aid reservoir, and using the test programme.
1 2 3 4 Reference* 5 6 7 8
removing the
remnants on the
soiled dishes that
will be kept waiting
in the machine for a
few days, and thus,
for preventing the
bad odor buildup.
- Few Few Medium Medium High High Medium to high
- A A A+B A+B A+B A+B A
Pre-wash
▼
End
20 30 71 170 60 128 124 69-163
7 9,6 12,4 12 9,4 17,2 15,4 9,8-13,6
0,5 0,75 0,8 1,01 1,08 1,40 1,67 0,74-1,33
Suitable for lightly
soiled daily dishes
that are scraped or
pre-cleaned.
Wash
▼
Cold rinse
▼
Hot Rinse
▼
End
Suitable for dishes
that are not pre-
cleaned but washed
immediately.
Pre-wash
▼
Wash
▼
Cold rinse
▼
Hot Rinse
▼
Dry
▼
End
Most economical
washing program for
the medium soiled
daily dishes that are
kept waiting.
Pre-wash
▼
Wash
▼
Cold rinse
▼
Hot Rinse
▼
Dry
▼
End
Daily washing program
at which the medium
soiled dishes that
are kept waiting are
cleaned in the fastest
way.
Wash
▼
Cold rinse
▼
Hot Rinse
▼
Dry
▼
End
Suitable for heavily
soiled dishes, pots and
pans.
Pre-wash
▼
Wash
▼
Cold rinse
▼
Hot Rinse
▼
Hot Rinse
▼
Dry
▼
End
Suitable for the dishes
which require extra
hygiene such as
articles for babies. Also
suitable for heavily
soiled dishes.
Pre-wash
▼
Wash
▼
Cold rinse
▼
Hot Rinse
▼
Hot Rinse
▼
Dry
▼
End
Determines the
soiling degree of
the dishes and sets
the temperature
and amount of the
washing water as well
as the washing time
automatically. Suitable
for all types of dishes.
The programme
sequence is adjusted to
the amount of soiling
17 7215 01 00-00-GB5019 496 01901
Loading...